Professional Documents
Culture Documents
Production Code
The correct production code must be used to locate the correct part numbers, otherwise incorrect parts may be supplied. If a particular production code is not listed, you must contact technical support for advice before ordering any parts.
CE37LD81-B
Model Power Board FAV Board LED Board Key Board R/C Right Speaker Left Speaker Panel Chasis LVDS Cable
Prod Code 10047951 20319694 20309015 20315065 20345995 20328881 20308713 20308712 30044228 20337555 30048584 17MB22 37781 SANYO SANYO CE37LD81-B MD.ASY.17PW20-37" TFT 170-270V MD.ASY.17FAV14-AV/HP/SV/LO/SPDIF(MB22) MD.ASY.17LD55-37-40781(MB15) MD.ASY.17TK83S-6SW 37-42750/51 (MB22) R/C 1050 SANYO (GRAY/S) SPK.ASY.42720TFT(MB11/15-L/MB22-R)JIEFU SPK.ASY.42720TFT(MB11/15-R/MB22-L)JIEFU TFT LCD 37''W LG LC370WX1-SL01SAFE RoHS CHS.ASSY.17MB22-21112222422531221147 CNAS 30P/230 LVDSW/FER UL20276 AWG30RoHS
CE42LD81-B
Model Power Board FAV Board LED Board Key Board R/C Right Speaker Left Speaker Panel Chasis LVDS Cable
Prod Code 10049155 20301443 20309015 20315065 20345995 20328881 20308713 20308712 30052454 20347999 30058240 17MB22 42781 SANYO SANYO-CE42LD81-B MD.ASY.17PW16-2-42" TFT 170-270V(W/CABLE MD.ASY.17FAV14-AV/HP/SV/LO/SPDIF(MB22) MD.ASY.17LD55-37-40781(MB15) MD.ASY.17TK83S-6SW 37-42750/51 (MB22) R/C 1050 SANYO (GRAY/S) SPK.ASY.42720TFT(MB11/15-L/MB22-R)JIEFU SPK.ASY.42720TFT(MB11/15-R/MB22-L)JIEFU TFT LCD 42"W LG LC420WX5-SLA1 SAFE RoHS CHS.ASSY.17MB22-21112222422531221148 CNAS 30P/350 MB22LVDSUL20276 AWG30RoHS
Inverter and LCD Panel Control Pcbs are normally part of the complete LCD Panel SANYO will supply separately subject to availability.
Model Inverter (LIPS) Pt. No. CE37LD81-B CE42LD81-B MASTER SLAVE MASTER SLAVE 30048243 30048244 30054783 30059001 Display Ctrl Pcb (Top rear of LCD panel) Pt. No. 30054730 30054729
Production Code
Part Number
TV Model: CE37LD81-B
Master Inverter Power Supply Pcb Display Control Pcb Digital Freeview Pcb
Key Pcb
AV Pcb RCU & LED Pcb Signal Pcb (Audio/ Video / CPU & Scaler) Slave Inverter HDMI Pcb
LCD Display Panel Replaceable only with prior TECHNICAL AUTHORISATION. Inverter (Back Light) Pcb Display Control Pcb (fitted inside rear of LCD Panel) (Both supplied as part of LCD Panel but available as spare separately). Signal Pcb - spares name - Chassis RCU / LED Pcb - spares name - LED Board Digital Freeview Pcb - spares name - DTT Board Power Supply Pcb - spares name - Power Board HDMI Pcb - spares name - HDMI Input Board AV Pcb - spares name - FAV Board Key Pcb - spares name - Key Board
PL809 AC IN
F800 T2.5A
All other Voltages shown are with reference to the isolated metal chassis
+24V
3v2 2v5
2v5
Run Supplies
3v3 5V Standby
7.8V (pulsing) Standby (front LED lit) 0V Side Standby Key button pressed in
Note :- This model has a low power mode, which switches off the CPU standby supplies and front LED, when the latching side standby key button is pressed. (The TV will appear completely 'Dead' and cannot not be operated by the RCU). In this mode 340VDC is still supplied by the bridge rectifier to the unisolated primary components, which are still Live..
FPC connector to Digital Pcb Audio, Video & Control Bus 12V LCD Panel Supplies PL406
5V Stby
L/S
3V2 Run
L/S
3V3 Stby
3V3 Run
4V9 Run
1V8 Stby
2v5 Run
LVDS Drives & Clocks measure 200mv on 100MHz Scope using x 10 probe. These may be very low or look non existent on a low bandwidth scope If all LVDS drives are present, the clock signals can be assumed to be OK. (See LVDS / Clock waveform pages)
-+ -+ -+
IC001
0.6V Stby
3V3 Stby
PL302 Digital Pcb PL001 To PL801 PSU PL602 to LED / RCU Pcb
24V To Run
VCTP
Main CPU, Video TXT, Audio, Scaler LED 4v3 Run 3v2 Stby 3v9 (Dips with RCU) Always +5V
12V Run
IC 101 AGC
PL411
IC200 PC in
TU100
Combined UHF / VHF / CATV Analogue & Digital Tuner
IC903 RGB
10V5 Run
To PL205 FAV Pcb IC905 Audio SW
9.1V Run
Pc Input
Srv Port
TV Model: CE42LD81-B
Master Inverter Power Supply Pcb Display Control Pcb Digital Freeview Pcb
Key Pcb
AV Pcb RCU & LED Pcb Signal Pcb (Audio/ Video / CPU & Scaler) Slave Inverter HDMI Pcb
LCD Display Panel Replaceable only with prior TECHNICAL AUTHORISATION. Inverter (Back Light) Pcb Display Control Pcb (fitted inside rear of LCD Panel) (Both supplied as part of LCD Panel but available as spare separately). Signal Pcb - spares name - Chassis RCU / LED Pcb - spares name - LED Board Digital Freeview Pcb - spares name - DTT Board Power Supply Pcb - spares name - Power Board HDMI Pcb - spares name - HDMI Input Board AV Pcb - spares name - FAV Board Key Pcb - spares name - Key Board
PL809 AC IN
F800 T2.5A
+
390V Run 340v Stby REF UNISOLATED GROUND All other Voltages shown are with reference to the isolated matal chassis
2v7
3v2
2v7
2v5
Run Supplies
3v3 5V Standby
8V (pulsimg) Standby (front LED lit) 0V Side Standby Key button pressed in
Note :- This model has a low power mode, which switches off the CPU standby supplies and front LED, when the latching side standby key button is pressed. (The TV will appear completely 'Dead' and cannot not be operated by the RCU). In this mode 340VDC is still supplied by the bridge rectifier to the unisolated primary components, which are still Live.
FPC connector to Digital Pcb Audio, Video & Control Bus 12V LCD Panel Supplies PL406
5V Stby
L/S
3V2 Run
L/S
3V3 Stby
3V3 Run
4V9 Run
1V8 Stby
2v7 Run
LVDS Drives & Clocks measure 200mv on 100MHz Scope using x 10 probe. These may be very low or look non existent on a low bandwidth scope If all LVDS drives are present, the clock signals can be assumed to be OK. (See LVDS / Clock waveform pages)
-+ -+ -+
IC001
0.6V Stby
3V3 Stby
PL302 Digital Pcb PL001 To PL801 PSU PL602 to LED / RCU Pcb
24V To Run
VCTP
Main CPU, Video TXT, Audio, Scaler PL400
IC902 Video Switch To PL204 FAV Pcb Ground to PL802 PSU IC004 IC904 Audio Switch
IC 101 AGC
LED 4v3 Run 3v2 Stby 3v9 (Dips with RCU) Always +5V
12V Run
PL411
IC200 PC in
TU100
Combined UHF / VHF / CATV Analogue & Digital Tuner
IC903 RGB
10V5 Run
To PL205 FAV Pcb IC905 Audio SW
9.1V Run
Pc Input
Srv Port
The Digital IF signal is fed into PL302 from the combined Analogue / Digital tuner assembly on the signal Pcb on the 'D' series models. The +12V power to PL501 is always present from plug PL804 on the main power supply. PL102 is connected to the Signal Pcb service port, by PL411 and allows firmware updates to the Digital Processor IC.
IC 101
IC202
The FPC, flexible printed circuit connector from PL202, allows Audio & Video data and also control bus operation from PL207 on the signal Pcb. PL103 supplies the SPDIF (Sony Philips Digital Interface) signal to the FAV Pcb for connection to external equipment
Card Reader
TU100
Figure 1 Negative LVDS waveform example This waveform is an example of the differential signal which may be observed on the LVDS output plug. See Signal Pcb Diagram for specific pins. All negative pulses should be similar in amplitude and frequency (70-80Mhz). The signal has a DC level of between 1.125V and 1.375V depending upon the type of input signal.
Figure 2 Positive LVDS waveform example This waveform compliments the negative version shown above; See Signal Pcb Diagram for specific pins. All positive pulses should be similar in amplitude and frequency (70-80Mhz). The signal has a DC level of between 1.125V and 1.375V depending upon the type of input signal.
Figure 3 LVDS clock waveform This waveform should be present in both positive and negative form on the LVDS output plug . See the Signal Pcb Diagram for specific pins. The clock frequency is specified as 74.25MHz but may be anywhere between 70MHz and 80MHz. The waveform has an offset of approximately 1V DC.
NO SOUND OR PICTURE
Yes
No
Check all Run voltage supplies from PSU at the Signal Pcb (See Signal Pcb Diagram) If incorrect check PSU supplies If all OK. Replace faulty loudspeaker, or replace Signal Pcb.
Check the five LCD panel +Ve supplies at Main Pcb LVDS LCD panel connector Yes PL406. (See Signal Pcb diagram). Also check all eight LVDS and two CLK waveforms with scope at LCD panel connector. (see Signal Pcb and LVDS diagrams) If OK, do continuity check on LVDS cable. If cable OK, try replacement display control pcb (top rear of LCD panel under metal cover). If still faulty then replace the LCD Panel assy. If voltages / waveforms not OK then check all supplies on the Signal Pcb at PL002 and PL003. (see Signal Pcb diagram). If voltages OK, replace the Signal Pcb. If voltages incorrect replace the PSU
Are Backlights
No
Check all voltages to the Inverter Pcb at PSU PL801 / PL802 and Run voltages at PL803 & PL805. (See PSU diagram) If all voltages from the PSU are OK, check the inverter Pcbs for D/J or replace. If after replacing the inverter Pcb, the backlights are still not lit, then one or more of the backlight lamps could be faulty. If PSU voltages are incorrect, then replace PSU Pcb.
Lit ?
If one channel of either of the inverters is not functioning due to a faulty inverter Pcb or a faulty lamp, then the backlights will light initially and then the inverter board will shut down with no picture, but the sound will still be present if previously tuned in.
Produced in the UK by Mike Burnett Senior Technical Liaison & Training Engineer SANYO Europe Ltd