Professional Documents
Culture Documents
Backcheck valve
At approximately 70 of the open cycle, the Backcheck Valve begins to slow the door's motion Prevents the door from slamming into the door's stop Valve is used to control the intensity of the Backcheck Note: A Positive stop is required; Backcheck cannot be used as a stop
Copyright 2005, 2008, SARGENT Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
ANSI Standards
ARM O P9 H PH9 F TYPE CO2011 CO2021 CO2051 CO2061 CO2091 ARM PF9 P10 PS/CPS CPSH/PSH TYPE CO2101 CO2021 CO2021 CO2061
6/1/08
1-800-727-5477 www.sargentlock.com
351 Series
2-3/16" (55mm)
The standard application of the 351 door closer is the most common and the most desirable. The closer mounts on the hinge (pull) side of door (except when the W Corner Bracket is used). Note: This application is not recommended on exterior doors (the closer is not protected from weather). The cover projection normally limits the door opening to a maximum of 160.
13" (330mm)
Interior Doors Opening In or Out Exterior Doors Opening In Maximum Reveal 7/16" Non-hand universal body
6/1/08
1-800-727-5477 www.sargentlock.com
351 Series
O - Standard Arm
Forged Steel Main Arm Non-handed Permits 120 door opening with standard mounting Permits 180 door opening with alternate mounting or corner bracket
Order as 25-O x finish for arm only Includes: 63-2607 - Main arm 63-2216 - Foot assembly 63-3684 - Screw pack
UH Package
Universal hold open arm package provides brackets and arms to install closer in top jamb, standard or parallel applications Order closer as 351-UH x finish 351-UH not available with (MC) metal cover or plated finishes
UO Package
Universal arm package provides brackets and arms to install closer in standard top jamb or parallel applications Order closer as 351-UO x finish 351-UO not available with (MC) metal cover or plated finishes
Ceiling
OLC - Low Ceiling Application Arm for Ceiling to Doors Clearance 1-1/4" 1-1/2"
Door Top Rail Requirement 4-1/4" min. rail (108mm) 351 closer can be mounted on top rails 2-3/8" through 4-1/4" using a 351-A mounting plate
1-1/4"1-1/2"
1-800-727-5477 www.sargentlock.com
6/1/08
Copyright 2005, 2008, SARGENT Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
351 Series
13" (330mm)
3-7/8" (98mm)
1-1/4" (32mm)
OZ ARM SHOWN Top Jamb applications - The 351 closer is mounted on the frame face above the door. The foot is mounted on the push side of door. This application is for use on exterior doors opening out to protect the closer from the weather.
Varies 3-3/8" to 6-5/8"
For reveals up to 2" (51mm) maximum O Arm - Max. Door Opening: 180 H Arm - Hold Open Range: 80-180 F Arm - Fusible Link Hold Open Arm Hold Open Range: 80-130
Reveal Depth
Copyright 2005, 2008, SARGENT Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
1-7/16" (37mm)
6" (152mm)
9" (229mm)
6/1/08
1-800-727-5477 www.sargentlock.com
351 Series
Narrow Reveal
O - Standard Arm
Forged Steel Main Arm For reveals up to 2" (51mm) Non-handed Permits 180 door opening
Order as 25-O x finish for arm only Includes: 63-2607 - Main arm assembly 63-2216 - Foot assembly 63-3684 - Screw pack
FZA - Fusible Link Hold Open Arm for Extra Deep Reveal
Forged Steel Main Arm For reveals 5-1/8" (130mm) to 8" (203mm) Adjustable friction holder Handed same as the door Permits 140 door opening 160 F link standard Specify 125 F link when required
Order as 25-FZA x hand x finish for arm only Includes: 63-2240 - Left hand main arm assembly 63-2241 - Right hand main arm assembly 63-2218 - Foot assembly 63-3684 - Screw pack
1-800-727-5477 www.sargentlock.com
6/1/08
351 Series
P9 Parallel Arm
Varies 5-7/8" to 6-3/8" (149mm to 162mm)
3-7/8" (98mm)
P9 ARM SHOWN
13" (330mm)
2-3/16" (56mm)
Parallel Arm Applications - The 351 closer is mounted on the push side of the door. As the door opens, the closer swings with the door and gives full headroom in the door opening. Other advantages: the closer arm does not project into the room; the frame can be quite narrow and the door can be swung open much farther than in Top Jamb Applications.
Stop arms
6 mounting positions allow stop from 85110
Copyright 2005, 2008, SARGENT Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
6/1/08
1-800-727-5477 www.sargentlock.com
351 Series
P10 - Heavy Duty Parallel Arm
Forged Steel Constructions Non-Handed Easily installed Permits 120 opening at standard mounting Permits 180 opening at alternate mounting
Order as 25-P10 x finish for arm only 25-P10 Includes: 63-0641 - Main arm 63-3727 - P10 foot assembly 63-3684 & 63-2392 - Screw packs
Forged Steel Constructions Handed arm is field-reversible Provides built in stop from 85 to 110 Permits 110 opening maximum Easily installed Permits 85 to 110 door opening
Order as 25-PS x finish for arm only Includes: 63-0641 - Main arm 63-3837 - PS foot assembly 63-3684 & 63-2398 - Screw packs
Forged Steel Constructions Provides built in compression stop from 85 to 105 Permits 105 opening maximum Easily installed Handed arm is field-reversible Dead stop within 3
Order as 25-CPS x finish for arm only Includes: 63-0641 - Main arm 63-3830 - CPS foot assembly 63-0516 - Bumper holder 63-3493 - Bumper 63-3684 & 63-2398 - Screw packs
PSH - Heavy Duty Parallel Hold Open CPSH - Heavy Duty Hold Open Arm with Positive Stop Parallel Arm with Compression Stop
Forged Steel Constructions Provides holder and stop features Handed arm is field-reversible Easily installed/adjusted Permits 85 to 110 door opening
Order as 25-PSH x finish for arm only Includes: 63-0641 - Main arm 63-3833 - PSH foot assembly 63-3684, 63-2392 & 63-2398 - Screw packs
Forged Steel Constructions Handed arm is field-reversible Provides built in compression stop and holder mechanism from 85 to 105 Easily installed/adjusted Permits 105 opening maximum Dead stop within 3
Order as 25-CPSH x finish for arm only Includes: 63-0641 - Main arm 63-3836 - CPSH foot assembly 63-0516 - Bumper holder 63-3493 - Bumper 63-3684, 63-2392 & 63-3487 - Screw packs
Forged Steel Constructions Adjustable hold open from 75 to 180 Forged steel arm 11-1/4" (286mm) long Handed same as door Use friction hold open arms for doors subject to moderate hold open use
Order as 25-PH10 x finish for arm only 25-PH10 Includes: 63-0641 - Main arm 63-3839 - Left hand PH10 foot assembly 63-3840 - Right hand PH10 foot assembly 63-3684 & 63-2392 - Screw packs
The PSH and CPSH arms project 2 3/4" below the head stop
1-800-727-5477 www.sargentlock.com
6/1/08
Copyright 2005, 2008, SARGENT Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Same as P10, except factory assembled at arm joint (elbow) to prevent disassembly in SSP package along with metal cover
351 Series
P4H - Flush Frame, Friction Hold Open Arm
Forged Steel Main Arm Holds open from 75 to 180 Easily adjusted by wrench Non-handed Use on frames where stop or soffit is too narrow to mount the standard hold open foot bracket
Order as 25-PH4 x finish for arm only Includes: 63-2229 - Main arm 61-2303 - Foot assembly 64-0050 - Foot bracket 63-3684 & 63-2391 - Screw packs
Order as 25-P3 x finish for arm only Includes: 63-2607 -Main arm 63-2270 -Foot assembly 63-3684 & 63-2391 - Screw packs
UO Package
Universal arm package provides arms and brackets to install closer in standard top jamb or Screw pack parallel 63-3684 application
351-UO not available with (MC) metal cover or plated finishes
125-P9
UH Package
Universal hold open arm package provides brackets and arms to install closer in top Screw pack jamb, standard 63-3684 or parallel applications
351-UH not available with (MC) metal cover or plated finishes
125-PH9
10
6/1/08
1-800-727-5477 www.sargentlock.com
351 Series
581-2 Blade Stop Spacer Kit
For frames with 1/2" blade stops For use with P10, PH10, PS, PSH, CPS and CPSH arms 125-V bracket included Packed with 1-1/4" long screws
Use P/N 63-0756 to order blade stop only
125-V
125-VF
For use with all heavy duty parallel arms Use 125-V for narrow stop and frame conditions Use 125-VF for flush door and frame conditions
Designed to replace a LCN 4040 closer body with a SARGENT 351 without drilling new holes in door (NOTE: new mounting holes required for arm bracket only)
9" (229mm)
Plates are non-handed Available in powder coat and plated finishes Order as: 351L x finish Consult factory when replacing LCN stop arm
1-800-727-5477 www.sargentlock.com
11
6/1/08
Copyright 2005, 2008, SARGENT Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
For frames with 1/2" blade stops For use with P9, PH9 and PF9 arms only Packed with 1-1/4" long screws
351 Series
Pull Side Mounting (Hinge Side)
The closer is for use on interior doors opening in or out. As the door opens, the closer swings with the door. This affords a variable hold-open feature option.
The closer is for use on interior doors opening in or out. As the door opens, the closer swings with the door. This affords a variable hold-open feature option.
Copyright 2005, 2008, SARGENT Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Common Features
Standard Finishes
EAB, EB, ED, EN, EP, powder coated on all exposed surfaces Architectural plated arms and covers optional
Arm
Forged steel
Holder (optional)
Mounts within the track (adjustable)
Bumper (optional)
Mounts in track to assist backcheck Not designed to be used as a stop Auxiliary stop is required Available for both regular or hold open tracks
Non Sized-Adjustable
Interior doors to 5'0" wide Shipped factory preset for 3'0" door Factory pre-sized upon request
Track
Extruded aluminum track
12
6/1/08
1-800-727-5477 www.sargentlock.com
351 Series
ODS - Single Step Double Egress Arm
23-5/8" (600mm)
18-1/2"
1/4" Maximum Frame Projection Permitted From Face of Door 5/8" (16mm)
2-3/16"
ODS Applications
160 maximum door opening 120 opening with bumper option Range of hold open 85-120 Used with reveals 1/8" to 3" (3mm-76mm) Double egress track arms are used when the aesthetics of a track application is required on the pull side of a deep reveal frame. This application is commonly used on cross corridor openings.
OD Applications
160 maximum door opening 120 opening with bumper option Range of hold open: 85-120 Used with reveals 3" to 4" (76mm-101mm)
Track
Extruded aluminum track End caps finished to match track
Track
Copyright 2005, 2008, SARGENT Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Arm
Forged steel Bearing roller Arm handed same as door
Arm
Forged steel Bearing roller Arm is handed same as door
Non Handed
Universal body
Non Handed
Universal Body
Bumper (optional)
Mounts in track to assist backcheck Not designed to be used as a stop Auxiliary stop is required Available for both regular or hold open tracks
Bumper (optional)
Mounts in track to assist backcheck Not designed to be used as a stop Auxiliary stop is required Available for both regular or hold open tracks
Holder (optional)
Mounts within the track (adjustable)
Holder (optional)
Mounts within the track (adjustable)
Non Sized-Adjustable
Interior doors to 5'0" wide Shipped factory preset for 3'0" door Factory pre-sized upon request
Non Sized-Adjustable
Interior doors to 5'0" wide Shipped factory preset for 3'0" door Factory pre-sized upon request
1-800-727-5477 www.sargentlock.com
13
6/1/08
351 Series
OP - Double Lever Arm Application
Wall
Wall
Arm
Forged steel
Arm
Forged steel Bearing roller
Non Handed
Universal Body
Non Handed
Universal Body
Door
Copyright 2005, 2008, SARGENT Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
26-3/8"
Door
7"
18-3/4"
14
7"
2-1/8" 2-1/8"
6-13/16" 6-13/16"
Top View
WALL WALL DOOR DOOR
17"
Pocket Depth POCKET DEPTH 2-5/8" MIN 2-5/8" Min 4-1/8" MAX 4-1/8" Max
Top View
1-3/4" 1-3/4"
Pocket Depth 2-5/8" Min 4-1/8" Max
18-3/4"
6-1/8" 6-1/8"
WALL WALL
1 3/4"
Wall Wall
DOOR DOOR
2-1/4" 2-1/4"
6/1/08
1-800-727-5477 www.sargentlock.com
351 Series
When a floor or wall stop cannot be used the highest level of door control is provided with the use of a SARGENT door closer and a SARGENT overhead stop or holder. While door closer arms are available with stop and holder options, they are limited in their ability to withstand extreme abuse. Overhead stops absorb abusive loads using a heavy compression spring that distributes the load to the frame. SARGENT overhead stops and holders are designed for years of abuse and come with a 5 year warranty
Frame
590 Door
Special Conditions
The SARGENT Website (www.sargentlock.com) contains templates for all common applications of SARGENT Door Closers with SARGENT overhead door holders. To ensure a satisfactory installation for other holders, it is recommended that complete details be submitted as follows: Type, size and make of holder Holding position (maximum door opening) Submit holder template being used In the case of unusual door, frame and hinge conditions where regular products do not meet requirements, submit drawings and complete details specifying the degree of door openings required, the type and size of hinge and the maximum door opening angle. Closer application being used Size and type of hinge
1-800-727-5477 www.sargentlock.com
15
6/1/08
Copyright 2005, 2008, SARGENT Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
351 Series
Packing
All closer assemblies are packaged 4 per carton. On request, door closers will be be packed 2 per carton.
Series
351 Screw
Example 351 351 When delayed action is required specify suffix DA 351 DA See applicable catalog section for arms available 351 DA P10 EB Bronze Enamel to match 10B 351 DA P10 EB ED Bronze Enamel to match 20D EN Aluminum Enamel EP Bronze Enamel to match US10 EAB Brass Enamel to be used with brass finishes Optional Plated Finishes (Handed metal cover required) Symbol BHMA Description 3 605 Polished Brass 4 606 Dull Brass 9 637 Bright Bronze, Clear Coated 10 612 Dull Bronze 10B 613 Oxidized Dull Bronze, Oil Rubbed 26 625 Chrome 26D 626 Dull Chrome Non-handed 351 DA P10 EB When ordering mortise nuts, use suffix TB 1-3/4"(44.5mm) 351 DA P10 EB TB std door thickness. For all others, specify Special rust inhibitor process (arm only) suffix SRI 351 DA P10 EB TB SRI for additional protection in corrosive environments
Hand (Applies to F, PH and DE arms and metal covers only) Through Bolts and Mortise Nuts Corrosion Protection
Note: MicroShield can be added to your door closer. Specify prefix SG when ordering.
Example
25-PSH EN 125-P4 EB 351-C EN 351-MC + 26D + LH 351-D EB
Copyright 2005, 2008, SARGENT Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
PULL SIDE
PULL SIDE
16
6/1/08
1-800-727-5477 www.sargentlock.com
80 Series
Simplicity
SARGENT manufactures a full line of exit devices including vertical rod, rim and mortise devices for both standard and narrow stile doors. These devices provide the best combination of simplicity, strength, durability, aesthetics and innovation and are perfect for applications in commercial office buildings, medical and educational institutions.
Easy installation! Maintenance-free design Few moving parts less wear Modular construction Rekeying is accomplished without removing device from door
Aesthetics
Clean, simple, aesthetically pleasing design True architectural hardware finishes consistent with BHMA/ANSI standards Coastal Series and Studio Collection Levers adds a touch of elegance
Innovation
SARGENT introduces Beacon, a next generation exit device that creates a clearer pathway to safety during an emergency. The combination of audible and visible alerts built into the exit device makes Beacon unique and effective. Broad offering of electro-mechanical solutions for the most demanding access/egress control applications MicroShield anti-microbial finish coating offers a new level of protection SARGuide exit device contains an electroluminescent touchpad to enhance the visibility of exit locations in dark or smoke-filled passages and effectively improve the safety of any public building CTL (Center and Top Latching) Vertical Rod Devices offer less bottom rod convenience with true center latching for added security
Security
Double cylinder functions available Torx and spanner screws Anti-vandal trim options Master keying with SARGENT Security Key systems available (V-10, Signature, Keso F1, Keso and XC)
Microshield Coating
MicroShield
This revolutionary finish coating available on all SARGENT product lines, utilizes a silver-based antimicrobial compound from Agion Technologies
Copyright 1998-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
As part of their promise to provide innovative solutions to their customers, ASSA ABLOY Group companies offer the MicroShieldTM technology, a silver-based antimicrobial coating designed to stem the spread of germs and bacteria. MicroShieldTM is a trademark of Yale Security Inc., an ASSA ABLOY Group company.
The MicroShield protection is now available integrated within the 80 Series touch pad as well as the finish coating. MicroShield lasts for the life of the finish MicroShield coating permanently suppresses the growth of bacteria, algae, fungus, mold and mildew. It is effective against a broad spectrum of bacteria Non-toxic and completely safe. The Agion antimicrobial compound is EPA and NSF approved and FDA listed for use in medical and food preparation equipment Applications: Anywhere there is need for a clean environment (hospitals, laboratories, schools, medical centers, daycare, food processing etc.)
The Agion antimicrobial is not intended as a substitute for good hygiene. Coated products must still be cleaned to insure the surfaces will be free of destructive microbes. ASSA ABLOY makes no representations or warranties, express or implied, as to the efficacy of the Agion antimicrobial. A copy of the Agion warranty is available upon request. Agion is a registered trademark of Agion Technologies, Inc., Wakefield, MA, USA
The SARGuide illuminated exit device increases visibility of exit locations in dark or smoke-filled passages, supplementing existing codes for egress lighting SARGuide utilizes state-of-the-art FLATLITE electroluminescent lighting from E-Lite Technologies Inc. Green-blue electroluminescent light provides 3 to 5 times the visibility of other lights
Can be wired for continuous operation or activation by fire alarm system Exit devices are placed low enough on a door to provide an extended window of opportunity for safe emergency egress Supplements building exit signs required by code Intuitive operation. Integral EXIT signage guides users directly to the means of egress UL Listed for use on panic (UL 305) and fire-rated (UL10C) exit devices Available with mechanical, and many electro-mechanical, exit devices See pages 56 & 57 for information on the TL- & PL- offerings
09/05/08
1-800-727-5477 www.sargentlock.com
80 Series
Maximum Door Opening-Fire Doors
Type
Exit Device Door Material Single Door
Rim
Metal Wood Metal Wood Metal Wood Metal Metal Wood Metal Wood Metal Wood Metal
3 Hour 4' x 10' 3 Hour 4' x 10' 3 Hour 4' x 10' 3 Hour 4' x 10' 3 Hour 4' x 10' 3 Hour 4' x 10' 3 Hour 4' x 7' 90 Min 4' x 10' 90 Min 4' x 9'
3 Hour 6' x 7' 3 Hour 8' x 8' 3 Hour 8' x 8' 3 Hour 8' x 8' 3 Hour 8' x 8' 3 Hour 8' x 10'
3 Hour 8' x 8' 3 Hour 8' x 8' 3 Hour 8' x 8' 3 Hour 8' x 8'
3 Hour 8' x 8' 3 Hour 8' x 8' 3 Hour 8' x 8' 3 Hour 8' x 8' 3 Hour 8' x 10'
SVR SVR/Mortise
Mortise Lock
12-8700 12-NB8700 12-NB8700 12-SP8700 12-SP8700 12-PP8700 & 12-PR8700 12-PP8700 & 12-PR8700 12-MD8600 12-NB-MD8600
3 Hour 8' x 10' 3 Hour 8' x 10' 90 Min 8' x 9' 90 Min 8' x 9' 3 Hour 8' x 10' 3 Hour 8' x 10' 3 Hour 8' x 10'
3 Hour 8' x 10' 3 Hour 8' x 10' 3 Hour 8' x 9' 3 Hour 8' x 9' 3 Hour 8' x 10' 3 Hour 8' x 10' 3 Hour 8' x 10'
CVR
12-PP8600 & 12-PR8600 12-PP8600 & 12- PR8600 12-LS8600 12-LP8600 & 12-LR8600
1-800-727-5477 www.sargentlock.com
09/05/08
Copyright 1998-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Wood
CVR/Mortise
80 Series
8700 Series
Surface Vertical Rod Exit Device Features
Two point latching (top and bottom of the door) Top & bottom latchbolt projection adjustable through center case Standard bottom latch compatible with latchtrack thresholds (by others) Single and double door applications Devices are ANSI A156.3 2001 Grade 1 UL Fire and Panic listed Rods are 1/2" (13mm) brass, bronze or stainless steel Note: The 8700 Exit Device can not be used less bottom rod. If less bottom rod is desired, specify NB8700 Series Exit Device.
2-1/2" (64mm)
9/16" (14mm)
3/8" (10mm)
Door Widths
1-13/16" (46mm)
Copyright 1998-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
3-11/16" (94mm)
648 & 653 Strikes (Alternate Strikes for 8700 SVR Devices) 648 Strike
For doors having transom panel applications Black nylon coated
1-1/8" (29mm) 7/16" (11mm) 1 7/8" (48mm)
653 Strike
Alternate for 12-8700
1-3/4" (44mm) 1/2" (13mm)
2-1/2" (64mm)
09/05/08
14
1-800-727-5477 www.sargentlock.com
80 Series
Cylinder Notes:
16- Cylinder Dogging uses a 41 inside cylinder with 97 ring Removable core and 70 prefix cylinders require a 97-0351 cylinder rings for 700 Series ET Controls and 94-0153 ring for 100 & 300 Series Aux controls Less cylinder - SARGENT supplies standard blocking rings. Specify if using competitor cylinders When ordering BEST cylinders for use in SARGENT Exit Devices, use the following BEST product numbers: Mortise cylinder: 1-E74XC208 Rim cylinder: 1ESPL-7-AO5994
Prefixes Available
Signature System Signature, meets UL437 cylinder SARGENT XC Key System UL Fire Label Exit Devices Sliding bolt bottom case for 8700 Cylinder lockdown feature Pushbar without Lexan touchpad Construction Keying Conventional, XC and Signature Series 22 Construction Keying Conventional Cylinders (Existing Systems Only) 23 ANSI flat lip strike (8300, 8900, including 12- Prefix) *31 Doors over 1-3/4" and/or Panels 36 6 Lobe security head screws 37 Spanner head screws 43 Flush End Cap *53 Latchbolt monitoring switch 54 Internal micro switch in ET Control 55 Signal Switch in Rail (Request to Exit) 56 Remote Dogging/Latch Retraction 56-HK Remote Latch Retraction with manual Hex Key dogging 57 Delayed Egress (Magnet ordered separately) 58 Electric Dogging **59 Electroguard Self Contained Delayed Egress Device **BC59 Electroguard Boca Code (Door Status Switch required) 60 Disposable Construction Core 63 SARGENT Removable Core cyl. Includes masterkeying, grand masterkeying 64 SARGENT Removable Construction Core cylinder 65-73 6 Pin Uncombinated Small Format Interchangeable Cores 65-73-7P 7 Pin Uncombinated Small Format Interchangeable Type Cores 70 Exit device to accept Small Format Interchangeable Cores - no core provided 72 Exit device to accept Small Format Interchangeable Cores with Construction Core provided 73 Small Format 6-Pin interchangeable core (refer to CK-8 for available keyways) 73-7P Small Format 7-pin interchangeable core, (refer to CK-8 for available keyways) 75 Warning inside, Abrasive strip on rail 76 Knurled Outside Lever 77 Warning inside and outside, abrasive strip on rail, abrasive coating on Lever 81 Cylinder to accept Keso (83) and Keso F1 (F183) removable core no core provided F1-82 Keso Security Cylinder with Front Profile (Patent Pending) 82 Keso Security Cylinder F1-83 Keso Security Removable Core Cylinder with Front Profile (Patent Pending) 83 Keso Security Removable Core Cylinder 84 Keso Security Removable Construction Core Cylinder AL Alarmed Exit BR Bump Resistant Cylinder (Available with Conventional & XC Cylinders Only) ***BT Beacon- Emergency Audio & Visual egress system with a self contained Laser, Flashing LEDs & Audio alert GL Guarded Latchbolt for 8800 NB No Bottom Rod (Not available with 59- & BC59- ) PL SARGuide PL Photoluminescent Coated Push Rail (Touchpad eliminated) Exit Device furnished in Schlage C or E SC, SE Keyway (specify) SG MicroShield - Antimicrobial clear powder coat TL SARGuide Illuminated touchpad VA, VC, SARGENT V-10 Cylinders VS, VC, VS See V-10 Cylinder Section 10 10-UL +11 12 14 ++16 19 21
Wide
1-1/16" (27mm)
1-7/16" (37mm)
2-5/8" (67mm)
3" (77mm)
2-1/8" (54mm)
Neutral
Depressed
Rail Sizes
SARGENT offers four sizes of rails to accommodate 32", 36", 42" and 48" doors. These rails can be cut for smaller doors as specified in the chart below. SARGENT will cut all rails to size if door width is specified when the hardware is ordered.
Stock Size
E F J
Door Widths
Remarks
No cutting required for 32"(81cm) door No cutting required for 36" (91cm) door
37" to 42" No cutting required (94cm to 107cm) for 42" (107cm) door
Suffix
CPC Clear Powder Coat Recommended for exit devices used in full exterior application and highly corrosive areas with 32 and 32D finishes. How to order: 8313F x ETL x 32D x CPC
G 43" to 48" No cutting required (110cm to 122cm) for 48" (122cm) door
Note: For additional information on Electrified Exit Devices, see the Electrified Exit Device catalog at www.sargentlock.com
1-800-727-5477 www.sargentlock.com
63
09/05/08
Copyright 1998-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
80 Series
12Prefixes
How to Order
75
Function 04 - Night Latch 06 - Night latch 10 - Dummy 13 Classroom 15 - Passage
F
Rail Size E 24"-32" F 33"-36" J 37"-42" G 43"-48"
ETMR
Trim For ET trim specify ET followed by Lever design, See pages 46-48
12VDV
Voltage 12VDC 24VDC Voltage required for Solenoid Controlled Functions 70, 71, 73, 74, 75 & 76
RHR
Hand Finish RHR LHR
32D
Finish Available Finishes page 65
36"
Door Width If door width is supplied rails will be cut to size
84"
Opening Height Required for Vertical Rod Exit Devices
41"
AFF Center Line of Rail Above Finish Floor 41" Standard
84 - CVR Narrow
Copyright 1998-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Rail Sizes 16 For Entrance Listed Below Thumb are for LP, LR 28 - TP Piece & LS Devices Passage Trims and Legend Only 40 Pulls FW Dummy specify Trim AFF - Above Finish Floor Designation 43 - FW CTL - Center & Top Latching Exit L 36" Door as specified Classroom CVR - Concealed Vertical Rod by Device ET - SARGENT External Lever Trim 44 - FW M 42"-44" Type FM - FEMA Night Latch FW - Freewheeling Trim 46 - FW N 46"-48" HC - Hurricane Code Night Latch 62 - TP Night Latch Mounting Heights 63 - TP Classroom 41" (1041mm) from finished floor for 66 - TP standard application Entrance 38" (965mm) from finished floor for 70 elementary schools and to meet local Solenoid accessibility standards when a 100 or 300 Fail Safe Series Auxiliary Control is used (38" AFF w/Cyl must be specified) 71 Solenoid Hand Fail Secure w/Cyl Inside 73 Solenoid Fail Safe Right Hand 74 Left Hand Reverse Reverse Solenoid RHR LHR Fail Secure 75 Solenoid Fail Safe w/Cyl 76 Solenoid Fail Secure w/Cyl Outside
MD - Metal Door NB - No Bottom Rod SVR - Surface Vertical Rod TP - Thumb Piece Trim WD - Wood Door WS - Windstorm
1/8" (3mm)
Stop Height
1/4" (6mm)
SP87 - CTL SVR PP86 - CTL CVR PR86 - CTL CVR SP86 - CTL CVR LP86 - CTL CVR LR86 - CTL CVR LS86 - CTL CVR
09/05/08
64
1-800-727-5477 www.sargentlock.com
80 Series
2.01 EXIT DEVICES
A. Exit devices shall be 80 Series push rail devices as manufactured by SARGENT Manufacturing Company, New Haven, CT. B. Exit devices shall be certified to meet or exceed the requirements of ANSI/BHMA A156.3 Grade 1. C. Exit devices shall be listed by Underwriters Laboratories for panic and bear the UL label for life safety in full compliance with NFPA 80 and NFPA 101. Exit devices for fire labeled doors shall be UL listed as Fire Exit Hardware. D. Provide standard hex key dogging on non fire-rated exit devices, with cylinder dogging (i.e., SARGENT 16- prefix) as an option. E. Exit devices shall comply with UL10C and UBC 7-2 positive pressure requirements. F. Construction: 1. Chassis shall be of heavy duty cast design with one piece drawn nonferrous removable covers matching the material of the push and mounting rails. 2. Stamped steel chassis are not acceptable. 3. Mounting rails shall be formed from a solid single piece of stainless steel, brass or bronze no less than 0.072 inches thick. 4. Push rails shall be constructed of 0.062 inch thick material in the same manner as the mounting rail. Painted or anodized aluminum shall not be considered heavy duty and are not acceptable. 5. Provide protective Lexan touchpad on the exit device push rail to prevent scratches and serve as a visible guide to the user. 6. Metal end caps shall be formed from the same base metal as the push and mounting rails. G. Exit devices shall have a maximum of 3 inches projection from the face of the door in the non-dogged position. When in the dogged position, the device shall have no more than a 2-1/8 inch projection from the door face. H. The design of the exit device shall eliminate the necessity of removing the device from the door for standard maintenance or keying changes. I. The device chassis shall be mounted and operable without the need of the rail or the chassis cover. J. Trim shall be through-bolted. K. Devices shall be available with matching trim for both wide and narrow stile doors, including electrified functions when required. L. Exit device operating lever trim shall withstand 1000 inch pounds of torque without allowing access. M. Lever trim shall be available in architectural finishes and designs to match that of the locksets specified. N. Exit devices shall have a five year limited warranty. The following guidelines should be referenced regularly and as required for proper appearance and longevity of finish.
Finish SARGENT#
3 4 9 10 10B 10BL 15 20D 26 26D 32 32D
BHMA#
605 606 611 612 613 619 625 626 628 630
Description
Bright brass, clear powder coat Dull brass, clear powder coat Bright bronze Dull bronze, clear powder coat
How to clean
Oxidized satin bronze-lacquered Satin nickel plate Statuary bronze, dark Bright chrome Dull chrome Bright stainless steel *Dull stainless steel Plastic pad or bronze wool Cleaners, solvents, bleach, steel wool Mild non-abrasive detergent with damp cloth or sponge Abrasive cleaners, bleach solvents, steel or bronze wool
1-800-727-5477 www.sargentlock.com
65
09/05/08
Copyright 1998-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Series
87
Function
13
Rail Lgth
F
Trim
ETL
Hand
RHR
Outside Finish
32D
Door Height
84"
AFF
41"
ANSI Type 2 8700 Panic & Fire 8706 x ET_ 8710 8710 x ET_ 8713 x ET_ 8715 x ET_ 8740 x ET_ 8743 x ET_ 8746 x ET_ 8773 x ET_ 8774 x ET_
Options
8700
Mechanical Options: 12141619313637435354555656-HK575859BC-5976858687ALBTCPCLDPLSGTBTLCylinder Options: 1010-2110UL10-631111-2111-6011-6311-6411-70-7P11-72-7P11-73-7P11-65-73-7P2122515260636470727365-7365-73-7P73-7P8182F1-8283F1-8384BRLCSCSE-
13 15 40 43 46 73 74
Freewheeling Trim
The lever rotates when the door is locked preventing excessive force from being applied to the horizontal lever
Electrified ET Trim
Voltage must be specified for the following functions: 73 and 74. Specify: 12VDC or 24VDC
Note: Exit devices are available in all standard finishes, except 14, 15, 26 & 26D. With these finishes, exit devices are supplied in 32 or 32D to match accordingly. 26 or 26D is automatically supplied when 32 or 32D is specified. For nickel finishes, specify 14/32 or 15/32D to receive nickel finished trims and stainless exit devices. Note: AFF means Above Finished Floor, center line of rail Above Finished Floor ** Cylinder Override is available with a 306 Aux Control Example Order: 8773F 12V x ETMG x 306 x RHR x 32D x 36"w x 84"h
06 10
300 Series Aux. Control 862 Pull
12 02 11
Key unlocks Turn; Turn retracts latch/ Turn relocks when key is removed #41 Cylinder Supplied 862 Pull Only (Optional Pulls: 863 & 864) Key Outside Unlocks/locks Turn #41 Cylinder Supplied
13
Note: When ordering 8700 Series Exit Device x 300 Series Aux. Control, specify 10 Function for the exit. Example: 8710F x 306 x RHR x 32D x 42" x 90" ++ Note: Exit Devices must be mounted 38" AFF when used with a 300 Series Auxiliary Controls to meet ICC/ANSI A117.1-2003 Accessible & Usable Buildings and Facilities Code
Trim Designations Use three letter designations (Ex PTB) when ordering the Exit Device with trim Use the six digit designation (Ex 866-MAL) when ordering trim without an Exit Device, always specify finish
Available Finishes
Description & Cylinder Info. (1-3/4" Door)
Pull Only (No Cylinder)*** Passage Only (No cylinder)
Key unlocks Trim, Trim retracts latch/ Trim relocks when key is removed #34 Cylinder Supplied
SARGENT Finishes
ANSI Finishes
8710 x Trim Designation 8728 x Trim Designation 8762 x Trim Designation 8763 x Trim Designation
*** Cylinder Override is available with a 306 Aux Control Note: Thumb piece trims for 62 and 63 function devices are identical and are identified as 66 function when trim is ordered separately. Note: FLW trim is not available in 32(629) or 32D(630)
1-800-727-5477 www.sargentlock.com
11
90641: D 8/30/10
605 606 611 612 613 614 618 619 624 625 626 629 630
Copyright 1998-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
A Lever
Handed
B Lever
8-1/16" (205mm)
4-5/8" (117mm)
E Lever
F Lever
*Projection varies by lever design. 2-1/2" (63mm) projection with L Lever Note: ET suffixes required when ordering ET trim without an exit device, see page 71 for complete details
4" (102mm)
4" (102mm)
J Lever*
Copyright 1998-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
L Lever*
P Lever*
1/2" (13mm)
1/2" (13mm)
4-11/16" (119mm)
4-1/2" (114mm)
W Lever
Pulls
2-3/4" (70mm)
862
4" (102mm)
863
4" (102mm)
864
3-1/2" (89mm)
1-3/4" (44mm)
4-11/16" (119mm)
62
1-800-727-5477 www.sargentlock.com
R - Rockport
Y - Yarmouth
G - Gulfport
S - Sanibel
4-1/2" (114mm)
FLL/FSL
FLW/FSW
MAL/MSL
2-5/8" (67mm) 2-1/16" (52mm)
14-5/16" (364mm)
14-5/16" (364mm)
14-1/4" (362mm)
STS
1-5/8" (41mm) 2-1/4" (57mm)
PTB/PSB
3-1/2" (89mm)
1-15/16" (49mm)
802-PTB
3-1/2" (98mm) 2-1/16" (52mm)
15" (381mm)
1-800-727-5477 www.sargentlock.com
63
90641: D 8/30/10
6" (152mm)
6" 152mm
Odon Series
Features
Studio Collection levers can be used with all SARGENT 80 Series exit devices with ET trim All levers - solid brass or stainless steel Available with all lever functions Lever finishes available: 03, 04, 09, 10, 10B, 10BL, 14, 15, 20D, 26, 26D, 32 & 32D Always specify hand
MN
MH
Centro Series
MC
Rialto Series
MO
MK
MS
MD
ML
MU
MV MJ MZ* MX* MP
Aventura Series
NS* MA NU*
Copyright 1998-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
ND*
NJ*
MB
REM**
MT
MI
RAM**
MM
MW*
RAS**
MY*
90641: D 8/30/10
RAW**
* Lever returns within 1/2" (13mm) of door face ** The Gramercy Levers are customized. Refer to page 65 on how to order
64
1-800-727-5477 www.sargentlock.com
REM
Lever
Plain With Raised Band With Metallic Insert With Wood Insert With Santoprenne Insert With Leather Insert
RCM
Part Number
REM RCM RAM RAW RAS RAL
Shank Finish*
Polish Stainless (629) or Satin Stainless (630) Polished Stainless (629) Polished Stainless (629) Polished Stainless (629) or Satin Stainless (630) Polished Stainless (629) or Satin Stainless (630) Polished Stainless (629) or Satin Stainless (630)
Grip Finish
Polish Stainless (629) or Satin Stainless (630) Polish Stainless (629) or Satin Stainless (630) Polished Stainless (629) Polish Stainless (629) or Satin Stainless (630) Polish Stainless (629) or Satin Stainless (630) Polish Stainless (629) or Satin Stainless (630)
* Rose and escutcheon finish is designated by shank finish selected Grip finish must match shank finish
Copyright 1998-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
To order Gramercy Series levers with 80 Series products, see the example below. When specifying finish, use the last two digits of the BHMA standard finish code, i.e. use 29 for polished stainless, BHMA finish 629.
AFF
Select RHR Select from Polished Polished Leather Black or RH, from 80 or satin or satin insert brown LHR, or 80 Series Series stainless stainless LH catalog catalog F RAL 29 BN 29 RH 32D 36"
10-
87
73
12VDC
84"
41"
1-800-727-5477 www.sargentlock.com
65
90641: D 8/30/10
Features
Heavy duty 12 gauge stainless steel in 32D finish Through-bolted for added strength Handed Specify RHR or LHR ADA Compliant #34 Rim Cylinder supplied for 8804
10-9/16" (268mm)
#41 Mortise Cylinder supplied for 8904 Night Latch and Dummy Functions available Available for MD & WD8610, 8710, 8804, 8810, 8904 & 8910 Devices Without protective lip for inactive door
AVT Retrofit Kit works easily with existing product with minor prep modification Order by part number (826, 824, 821 or 827) as determined by product & function below
Designed for exterior doors that require extra security or resistance to vandalism, anti-vandal trim (AVT) plates have an extended lip on the active side of the door to provide extra protection for the latchbolt. A matte plastic coated grip provides a comfortable pull over wide temperature ranges. Fully through-bolted with no exposed exterior fasteners for a cleaner look and increased security.
Description
Cylinder, but No Protective Lip Protective Lip & Cylinder No Protective Lip & No Cylinder Protective Lip & No Cylinder
Application
8804 Mfg after 02-2001 8904; also 8804 Mfg before 02-2001 MD & WD8610, 8710 and 8810 8910
Copyright 1998-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
ET Cover Plate
For all ET functions
3-1/2" (89mm)
Designed for severe windload (Hurricane Code) environments where surface bolts are required (e.g., on inactive doors) Tested to Dade County protocols Listed to UL 10C for use on fire rated door assemblies. Refer to codes for locations where surface bolts are allowed on fire doors All steel construction for maximum strength and heavy duty use Full 3/4" (19mm) square, 12" (305mm) bolt with 1-1/4" (32mm) throw Bright zinc-plated finish Jimmy-resistant design locks bolt automatically when thrown; released by pressing knob toward door while retracting Bolt can be locked in retracted or thrown position Angle (L shaped) and mortise strike with mounting hardware supplied standard
8-3/4" (222mm)
A decorative push bar for vestibule door applications where continuity of design is desired, but no exit device is required. Outside dummy trim available on order. Order as a: 8893 x finish; Specify door width and door stile width when ordering.
This plate is designed to be mounted behind the ET control to cover a stock hollow metal cutout Order as a: 68-0657 x finish
Push rail operates on this rail to simulate active doors. Can be used with dummy trim. Order as a: 8885 x Finish; specify door width and door stile width when ordering. Available with Request-to-Exit (REX) signaling switch; specify 55-8895 x Finish
90641: D 8/30/10
66
1-800-727-5477 www.sargentlock.com
80 Series
Simplicity
SARGENT manufactures a full line of exit devices including vertical rod, rim and mortise devices for both standard and narrow stile doors. These devices provide the best combination of simplicity, strength, durability, aesthetics and innovation and are perfect for applications in commercial office buildings, medical and educational institutions.
Easy installation! Maintenance-free design Few moving parts less wear Modular construction Rekeying is accomplished without removing device from door
Aesthetics
Clean, simple, aesthetically pleasing design True architectural hardware finishes consistent with BHMA/ANSI standards Coastal Series and Studio Collection Levers adds a touch of elegance
Innovation
SARGENT introduces Beacon, a next generation exit device that creates a clearer pathway to safety during an emergency. The combination of audible and visible alerts built into the exit device makes Beacon unique and effective. Broad offering of electro-mechanical solutions for the most demanding access/egress control applications MicroShield anti-microbial finish coating offers a new level of protection SARGuide exit device contains an electroluminescent touchpad to enhance the visibility of exit locations in dark or smoke-filled passages and effectively improve the safety of any public building CTL (Center and Top Latching) Vertical Rod Devices offer less bottom rod convenience with true center latching for added security
Security
Double cylinder functions available Torx and spanner screws Anti-vandal trim options Master keying with SARGENT Security Key systems available (V-10, Signature, Keso F1, Keso and XC)
Microshield Coating
MicroShield
This revolutionary finish coating available on all SARGENT product lines, utilizes a silver-based antimicrobial compound from Agion Technologies
Copyright 1998-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
As part of their promise to provide innovative solutions to their customers, ASSA ABLOY Group companies offer the MicroShieldTM technology, a silver-based antimicrobial coating designed to stem the spread of germs and bacteria. MicroShieldTM is a trademark of Yale Security Inc., an ASSA ABLOY Group company.
The MicroShield protection is now available integrated within the 80 Series touch pad as well as the finish coating. MicroShield lasts for the life of the finish MicroShield coating permanently suppresses the growth of bacteria, algae, fungus, mold and mildew. It is effective against a broad spectrum of bacteria Non-toxic and completely safe. The Agion antimicrobial compound is EPA and NSF approved and FDA listed for use in medical and food preparation equipment Applications: Anywhere there is need for a clean environment (hospitals, laboratories, schools, medical centers, daycare, food processing etc.)
The Agion antimicrobial is not intended as a substitute for good hygiene. Coated products must still be cleaned to insure the surfaces will be free of destructive microbes. ASSA ABLOY makes no representations or warranties, express or implied, as to the efficacy of the Agion antimicrobial. A copy of the Agion warranty is available upon request. Agion is a registered trademark of Agion Technologies, Inc., Wakefield, MA, USA
The SARGuide illuminated exit device increases visibility of exit locations in dark or smoke-filled passages, supplementing existing codes for egress lighting SARGuide utilizes state-of-the-art FLATLITE electroluminescent lighting from E-Lite Technologies Inc. Green-blue electroluminescent light provides 3 to 5 times the visibility of other lights
Can be wired for continuous operation or activation by fire alarm system Exit devices are placed low enough on a door to provide an extended window of opportunity for safe emergency egress Supplements building exit signs required by code Intuitive operation. Integral EXIT signage guides users directly to the means of egress UL Listed for use on panic (UL 305) and fire-rated (UL10C) exit devices Available with mechanical, and many electro-mechanical, exit devices See pages 56 & 57 for information on the TL- & PL- offerings
09/05/08
1-800-727-5477 www.sargentlock.com
80 Series
Maximum Door Opening-Fire Doors
Type
Exit Device Door Material Single Door
Rim
Metal Wood Metal Wood Metal Wood Metal Metal Wood Metal Wood Metal Wood Metal
3 Hour 4' x 10' 3 Hour 4' x 10' 3 Hour 4' x 10' 3 Hour 4' x 10' 3 Hour 4' x 10' 3 Hour 4' x 10' 3 Hour 4' x 7' 90 Min 4' x 10' 90 Min 4' x 9'
3 Hour 6' x 7' 3 Hour 8' x 8' 3 Hour 8' x 8' 3 Hour 8' x 8' 3 Hour 8' x 8' 3 Hour 8' x 10'
3 Hour 8' x 8' 3 Hour 8' x 8' 3 Hour 8' x 8' 3 Hour 8' x 8'
3 Hour 8' x 8' 3 Hour 8' x 8' 3 Hour 8' x 8' 3 Hour 8' x 8' 3 Hour 8' x 10'
SVR SVR/Mortise
Mortise Lock
12-8700 12-NB8700 12-NB8700 12-SP8700 12-SP8700 12-PP8700 & 12-PR8700 12-PP8700 & 12-PR8700 12-MD8600 12-NB-MD8600
3 Hour 8' x 10' 3 Hour 8' x 10' 90 Min 8' x 9' 90 Min 8' x 9' 3 Hour 8' x 10' 3 Hour 8' x 10' 3 Hour 8' x 10'
3 Hour 8' x 10' 3 Hour 8' x 10' 3 Hour 8' x 9' 3 Hour 8' x 9' 3 Hour 8' x 10' 3 Hour 8' x 10' 3 Hour 8' x 10'
CVR
12-PP8600 & 12-PR8600 12-PP8600 & 12- PR8600 12-LS8600 12-LP8600 & 12-LR8600
1-800-727-5477 www.sargentlock.com
09/05/08
Copyright 1998-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Wood
CVR/Mortise
80 Series
8800 Series
Rim Exit Device
Specifications
Door Types Door Widths
Copyright 1998-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Mounting Fasteners Latch Bolt Device Centerline from Finished Floor Center Case Dimensions Projection Fire Exit Hardware
649 Strike
Surface applied Panic & Fire Rated Black nylon coated
644 Strike
7/16" (38mm) 2" (92mm)
613 Strike
Mortised. Dimension L equals door thickness plus 1/2" (13mm). Black nylon coated on lip only.
Surface applied. For use on pairs of doors without mullion. Ductile Iron. Black nylon coated.
09/05/08
1-800-727-5477 www.sargentlock.com
80 Series
Cylinder Notes:
16- Cylinder Dogging uses a 41 inside cylinder with 97 ring Removable core and 70 prefix cylinders require a 97-0351 cylinder rings for 700 Series ET Controls and 94-0153 ring for 100 & 300 Series Aux controls Less cylinder - SARGENT supplies standard blocking rings. Specify if using competitor cylinders When ordering BEST cylinders for use in SARGENT Exit Devices, use the following BEST product numbers: Mortise cylinder: 1-E74XC208 Rim cylinder: 1ESPL-7-AO5994
Prefixes Available
Signature System Signature, meets UL437 cylinder SARGENT XC Key System UL Fire Label Exit Devices Sliding bolt bottom case for 8700 Cylinder lockdown feature Pushbar without Lexan touchpad Construction Keying Conventional, XC and Signature Series 22 Construction Keying Conventional Cylinders (Existing Systems Only) 23 ANSI flat lip strike (8300, 8900, including 12- Prefix) *31 Doors over 1-3/4" and/or Panels 36 6 Lobe security head screws 37 Spanner head screws 43 Flush End Cap *53 Latchbolt monitoring switch 54 Internal micro switch in ET Control 55 Signal Switch in Rail (Request to Exit) 56 Remote Dogging/Latch Retraction 56-HK Remote Latch Retraction with manual Hex Key dogging 57 Delayed Egress (Magnet ordered separately) 58 Electric Dogging **59 Electroguard Self Contained Delayed Egress Device **BC59 Electroguard Boca Code (Door Status Switch required) 60 Disposable Construction Core 63 SARGENT Removable Core cyl. Includes masterkeying, grand masterkeying 64 SARGENT Removable Construction Core cylinder 65-73 6 Pin Uncombinated Small Format Interchangeable Cores 65-73-7P 7 Pin Uncombinated Small Format Interchangeable Type Cores 70 Exit device to accept Small Format Interchangeable Cores - no core provided 72 Exit device to accept Small Format Interchangeable Cores with Construction Core provided 73 Small Format 6-Pin interchangeable core (refer to CK-8 for available keyways) 73-7P Small Format 7-pin interchangeable core, (refer to CK-8 for available keyways) 75 Warning inside, Abrasive strip on rail 76 Knurled Outside Lever 77 Warning inside and outside, abrasive strip on rail, abrasive coating on Lever 81 Cylinder to accept Keso (83) and Keso F1 (F183) removable core no core provided F1-82 Keso Security Cylinder with Front Profile (Patent Pending) 82 Keso Security Cylinder F1-83 Keso Security Removable Core Cylinder with Front Profile (Patent Pending) 83 Keso Security Removable Core Cylinder 84 Keso Security Removable Construction Core Cylinder AL Alarmed Exit BR Bump Resistant Cylinder (Available with Conventional & XC Cylinders Only) ***BT Beacon- Emergency Audio & Visual egress system with a self contained Laser, Flashing LEDs & Audio alert GL Guarded Latchbolt for 8800 NB No Bottom Rod (Not available with 59- & BC59- ) PL SARGuide PL Photoluminescent Coated Push Rail (Touchpad eliminated) Exit Device furnished in Schlage C or E SC, SE Keyway (specify) SG MicroShield - Antimicrobial clear powder coat TL SARGuide Illuminated touchpad VA, VC, SARGENT V-10 Cylinders VS, VC, VS See V-10 Cylinder Section 10 10-UL +11 12 14 ++16 19 21
Wide
1-1/16" (27mm)
1-7/16" (37mm)
2-5/8" (67mm)
3" (77mm)
2-1/8" (54mm)
Neutral
Depressed
Rail Sizes
SARGENT offers four sizes of rails to accommodate 32", 36", 42" and 48" doors. These rails can be cut for smaller doors as specified in the chart below. SARGENT will cut all rails to size if door width is specified when the hardware is ordered.
Stock Size
E F J
Door Widths
Remarks
No cutting required for 32"(81cm) door No cutting required for 36" (91cm) door
37" to 42" No cutting required (94cm to 107cm) for 42" (107cm) door
Suffix
CPC Clear Powder Coat Recommended for exit devices used in full exterior application and highly corrosive areas with 32 and 32D finishes. How to order: 8313F x ETL x 32D x CPC
G 43" to 48" No cutting required (110cm to 122cm) for 48" (122cm) door
Note: For additional information on Electrified Exit Devices, see the Electrified Exit Device catalog at www.sargentlock.com
1-800-727-5477 www.sargentlock.com
63
09/05/08
Copyright 1998-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
80 Series
12Prefixes
How to Order
75
Function 04 - Night Latch 06 - Night latch 10 - Dummy 13 Classroom 15 - Passage
F
Rail Size E 24"-32" F 33"-36" J 37"-42" G 43"-48"
ETMR
Trim For ET trim specify ET followed by Lever design, See pages 46-48
12VDV
Voltage 12VDC 24VDC Voltage required for Solenoid Controlled Functions 70, 71, 73, 74, 75 & 76
RHR
Hand Finish RHR LHR
32D
Finish Available Finishes page 65
36"
Door Width If door width is supplied rails will be cut to size
84"
Opening Height Required for Vertical Rod Exit Devices
41"
AFF Center Line of Rail Above Finish Floor 41" Standard
84 - CVR Narrow
Copyright 1998-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Rail Sizes 16 For Entrance Listed Below Thumb are for LP, LR 28 - TP Piece & LS Devices Passage Trims and Legend Only 40 Pulls FW Dummy specify Trim AFF - Above Finish Floor Designation 43 - FW CTL - Center & Top Latching Exit L 36" Door as specified Classroom CVR - Concealed Vertical Rod by Device ET - SARGENT External Lever Trim 44 - FW M 42"-44" Type FM - FEMA Night Latch FW - Freewheeling Trim 46 - FW N 46"-48" HC - Hurricane Code Night Latch 62 - TP Night Latch Mounting Heights 63 - TP Classroom 41" (1041mm) from finished floor for 66 - TP standard application Entrance 38" (965mm) from finished floor for 70 elementary schools and to meet local Solenoid accessibility standards when a 100 or 300 Fail Safe Series Auxiliary Control is used (38" AFF w/Cyl must be specified) 71 Solenoid Hand Fail Secure w/Cyl Inside 73 Solenoid Fail Safe Right Hand 74 Left Hand Reverse Reverse Solenoid RHR LHR Fail Secure 75 Solenoid Fail Safe w/Cyl 76 Solenoid Fail Secure w/Cyl Outside
MD - Metal Door NB - No Bottom Rod SVR - Surface Vertical Rod TP - Thumb Piece Trim WD - Wood Door WS - Windstorm
1/8" (3mm)
Stop Height
1/4" (6mm)
SP87 - CTL SVR PP86 - CTL CVR PR86 - CTL CVR SP86 - CTL CVR LP86 - CTL CVR LR86 - CTL CVR LS86 - CTL CVR
09/05/08
64
1-800-727-5477 www.sargentlock.com
80 Series
2.01 EXIT DEVICES
A. Exit devices shall be 80 Series push rail devices as manufactured by SARGENT Manufacturing Company, New Haven, CT. B. Exit devices shall be certified to meet or exceed the requirements of ANSI/BHMA A156.3 Grade 1. C. Exit devices shall be listed by Underwriters Laboratories for panic and bear the UL label for life safety in full compliance with NFPA 80 and NFPA 101. Exit devices for fire labeled doors shall be UL listed as Fire Exit Hardware. D. Provide standard hex key dogging on non fire-rated exit devices, with cylinder dogging (i.e., SARGENT 16- prefix) as an option. E. Exit devices shall comply with UL10C and UBC 7-2 positive pressure requirements. F. Construction: 1. Chassis shall be of heavy duty cast design with one piece drawn nonferrous removable covers matching the material of the push and mounting rails. 2. Stamped steel chassis are not acceptable. 3. Mounting rails shall be formed from a solid single piece of stainless steel, brass or bronze no less than 0.072 inches thick. 4. Push rails shall be constructed of 0.062 inch thick material in the same manner as the mounting rail. Painted or anodized aluminum shall not be considered heavy duty and are not acceptable. 5. Provide protective Lexan touchpad on the exit device push rail to prevent scratches and serve as a visible guide to the user. 6. Metal end caps shall be formed from the same base metal as the push and mounting rails. G. Exit devices shall have a maximum of 3 inches projection from the face of the door in the non-dogged position. When in the dogged position, the device shall have no more than a 2-1/8 inch projection from the door face. H. The design of the exit device shall eliminate the necessity of removing the device from the door for standard maintenance or keying changes. I. The device chassis shall be mounted and operable without the need of the rail or the chassis cover. J. Trim shall be through-bolted. K. Devices shall be available with matching trim for both wide and narrow stile doors, including electrified functions when required. L. Exit device operating lever trim shall withstand 1000 inch pounds of torque without allowing access. M. Lever trim shall be available in architectural finishes and designs to match that of the locksets specified. N. Exit devices shall have a five year limited warranty. The following guidelines should be referenced regularly and as required for proper appearance and longevity of finish.
Finish SARGENT#
3 4 9 10 10B 10BL 15 20D 26 26D 32 32D
BHMA#
605 606 611 612 613 619 625 626 628 630
Description
Bright brass, clear powder coat Dull brass, clear powder coat Bright bronze Dull bronze, clear powder coat
How to clean
Oxidized satin bronze-lacquered Satin nickel plate Statuary bronze, dark Bright chrome Dull chrome Bright stainless steel *Dull stainless steel Plastic pad or bronze wool Cleaners, solvents, bleach, steel wool Mild non-abrasive detergent with damp cloth or sponge Abrasive cleaners, bleach solvents, steel or bronze wool
1-800-727-5477 www.sargentlock.com
65
09/05/08
Copyright 1998-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Specifications
For Doors The 8888/8810 Rim Exit Device Devices are ANSI A156.3 2008 Grade 1 UL Fire and Panic listed Device is non-handed ANSI/BHMA architectural finishes Four standard sizes available To Order: Specify options, 8888 or 8810, Rail Size and Finish Example: 12-19-8888F x 32D Mounting Chassis Cover Chassis Rails Hand Dogging Feature
(Non 12- only)
Wood or metal. 1-3/4" (44 mm) minimum thickness. For doors over 1-3/4" to 2-1/4" thick, specify thickness and order as 31- option Supplied standard with wood and machine screws Available with through-bolts and mortise nuts Cold drawn stainless steel, brass or bronze with ANSI/BHMA Finishes Nonferrous alloy (Panic) Ferrous alloy (Fire Rated) Roll Formed Stainless Steel, Brass or Bronze with ANSI/BHMA Finishes Non-handed Hex key dogging standard on non fired rated devices; specify 16- for cylinder dogging (#41 cylinder supplied) Stainless steel, 3/4" (19mm) throw 649 Strike supplied standard for panic & fire rated openings See chart - Page 3
Rail Chart
- Rails are available in 4 sizes, use door width to determine size needed. - Rails will be factory cut to size if door width is supplied or can be cut in the field Stock Size Door Widths Remarks No cutting required for 32" (81cm) door No cutting required for 36" (91cm) door No cutting required for 42" (107cm) door No cutting required for 48" (122cm) door
Copyright 1998-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
8-1/16" (205mm)
E F J G
1-13/16" (46mm) 13/16" (21mm)
24" to 32" (61cm to 81cm) 33" to 36" (84cm to 91cm) 37" to 42" (94cm to 107cm) 43" to 48" (110cm to 122cm)
The 700 Series ET Control is sold separately from the exit device and can be used with 8888 & 8810 Exit Device. The trim is non handed and is through-bolted to the chassis for greater security and durability. Available in 7 functions and SARGENT Studio, Coastal and standard lever designs to accommodate most requirements. ANSI/BHMA Finishes Easy operating lever handle allows convenient one hand operation ET trim is not available in 32 or 32D Stainless steel levers are available
649 Strike
Supplied standard for panic & fire rated openings Surface applied Black nylon coated
3/4" (19mm) 3-11/16" (94mm) 1-5/32" (29mm)
1/4" (6mm)
90641: D 8/30/10
1-800-727-5477 www.sargentlock.com
Options
Exit
12*161943GLCPCLCLDPL-
Trim
10**10-UL1111-7011-72-7P11-73-7P2122606364+70+72+73+73-7P+65-73+65-73-7PBRLCSCSE++ SFSG-
All trims and functions listed on this page, work with 8888 & 8810 Exit Devices Available options listed at the right 8888 & 8810 are identical products and are non-handed Exit devices are not available in 14, 15, 26 and 26D finishes
Trim Designations 704 ET_ x Hand & Finish 710 ET_ x Hand & Finish 713-8 ET_ x Hand & Finish 715-8 ET_ x Hand & Finish 740 ET_ x Hand & Finish 743-8 ET_ x Hand & Finish 744 ET_ x Hand & Finish
15 40 43 44
* Supplied with standard 41 cylinder, for cylinder options, see trim options ** Double asterisked options are not available with 88 Lever & Rose Trim + Single crossed options are not available with 88 Lever & Rose Trim with J Lever ++ Double Cross options are only available with 88 Lever & Rose Trim
Freewheeling Trim
The lever rotates when the door is locked preventing excessive force from being applied to the horizontal lever
To order: Specify options followed by trim designation, lever design and finish (as shown to the right). Example: 10-SG-88-CLP x 26D
Description
Key Retracts Latch Cylinder Supplied No outside Operation (No Cylinder) Dummy Trim Key Outside Unlocks/locks Trim Cylinder Supplied Passage Only (No cylinder)
Trim Designations 88-KL_ x Finish 88-DL_ x Finish 88-CL_ x Finish 88-LL_ x Finish
03 02 08 14
Available Finishes
SARGENT Finishes ANSI Finishes
Lever Designs available for 88 Lever & Rose Trim are L, B, J & P Note: For 88 Lever & Rose trim, the 1st letter is the function, the 2nd is the L Rose Design & the 3rd is the lever design specified
Keyed & Non Keyed Pull Trim for 8888 & 8810 Devices Use the six digit designation (Ex "866-MAL") when ordering trim without an Exit Device, always specify options, designation, finish & hand Example: 10-SG-814-FSW x 04 x RHR SARGENT Function #'s 04 10 ANSI 03 02 Description & Cylinder Info. (1-3/4" Door)
Key Retracts Latch #34 Cylinder Supplied No O/S Operation or Cylinder (Pull Only)
814-FSL* 814-FSW*
Trim Designations
814-MSL*
814-PSB*
814-STS
605 606 611 612 613 614 618 619 624 625 626 629 630
810-FLL
810-FLW
810-MAL
810-PTB
Note: FSW, FLW, 88 Lever & Rose trim & ETs are not available in 32(629) or 32D(630) * FSL, FSW, MSL and PSB trims are used with (HC-& 12-) 8888 and 8804 only and are the same as FLL, FLW, MAL and PTB pulls, except for cylinder hole located 3/8" (9mm) lower.
1-800-727-5477 www.sargentlock.com
Copyright 1998-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Series
88
Trim
ETL
Hand
RHR
Outside Finish
26D
Inside Finish
32D
Door Width
36"
Options
8800
ANSI Type 1 8800 Panic & Fire 8804 x ET_ 8806 x ET_ 8810 8810 x ET_ 8813 x ET_ 8815 x ET_ 8816 x ET_ 8840 x ET_ 8843 x ET_ 8844 x ET_ 8846 x ET_ 8873 x ET_ 8874 x ET_ 8875 x ET_ 8876 x ET_
10 13 15 16 40 43 44 46
Freewheeling Trim
The lever rotates when the door is locked preventing excessive force from being applied to the horizontal lever
Electrified ET Trim
Voltage must be specified for the following functions: 73, 74, 75 and 76. Specify: 12VDC or 24VDC
73 74 75 76
Note: Exit devices are available in all standard finishes, except 14, 15, 26 & 26D. With these finishes, exit devices are supplied in 32 or 32D to match accordingly. 26 or 26D is automatically supplied when 32 or 32D is specified. For nickel finishes, specify 14/32 or 15/32D to receive nickel finished trims and stainless exit devices.
Trim Designations Use three letter designations (Ex PTB) when ordering the Exit Device with trim Use the six digit designation (Ex 866-MAL) when ordering trim without an Exit Device, always specify finish
Series
Available Finishes
SARGENT Finishes ANSI Finishes
814-FSL*
814FSW*
8804 x Trim Designation 8810 x Trim Designation 8828 x Trim Designation 8863 x Trim Designation 8866 x Trim Designation
810-FLL 810-FLW 810-MAL 810-PTB 810-STS 828-FLL 828-FLW 828-MAL 828-PTB 828-STS 866-FLL 866-FLW 866-MAL 866-PTB 866-STS
66
07
N/A
* FSL, FSW, MSL and PSB trims are used with (HC-& 12-) 8888 and 8804 only and are the same as FLL, FLW, MAL and PTB pulls except for cylinder hole located 3/8" (9mm) lower. Note: Thumb piece trims for 63 and 66 function devices are identical and are identified as 66 function when trim is ordered separately. Note: FLW & FSW trims are not available in 32(629) or 32D(630)
1-800-727-5477 www.sargentlock.com
90641: D 8/30/10
605 606 611 612 613 614 618 619 624 625 626 629 630
Copyright 1998-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
A Lever
Handed
B Lever
8-1/16" (205mm)
4-5/8" (117mm)
E Lever
F Lever
*Projection varies by lever design. 2-1/2" (63mm) projection with L Lever Note: ET suffixes required when ordering ET trim without an exit device, see page 71 for complete details
4" (102mm)
4" (102mm)
J Lever*
Copyright 1998-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
L Lever*
P Lever*
1/2" (13mm)
1/2" (13mm)
4-11/16" (119mm)
4-1/2" (114mm)
W Lever
Pulls
2-3/4" (70mm)
862
4" (102mm)
863
4" (102mm)
864
3-1/2" (89mm)
1-3/4" (44mm)
4-11/16" (119mm)
62
1-800-727-5477 www.sargentlock.com
R - Rockport
Y - Yarmouth
G - Gulfport
S - Sanibel
4-1/2" (114mm)
FLL/FSL
FLW/FSW
MAL/MSL
2-5/8" (67mm) 2-1/16" (52mm)
14-5/16" (364mm)
14-5/16" (364mm)
14-1/4" (362mm)
STS
1-5/8" (41mm) 2-1/4" (57mm)
PTB/PSB
3-1/2" (89mm)
1-15/16" (49mm)
802-PTB
3-1/2" (98mm) 2-1/16" (52mm)
15" (381mm)
1-800-727-5477 www.sargentlock.com
63
90641: D 8/30/10
6" (152mm)
6" 152mm
Odon Series
Features
Studio Collection levers can be used with all SARGENT 80 Series exit devices with ET trim All levers - solid brass or stainless steel Available with all lever functions Lever finishes available: 03, 04, 09, 10, 10B, 10BL, 14, 15, 20D, 26, 26D, 32 & 32D Always specify hand
MN
MH
Centro Series
MC
Rialto Series
MO
MK
MS
MD
ML
MU
MV MJ MZ* MX* MP
Aventura Series
NS* MA NU*
Copyright 1998-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
ND*
NJ*
MB
REM**
MT
MI
RAM**
MM
MW*
RAS**
MY*
90641: D 8/30/10
RAW**
* Lever returns within 1/2" (13mm) of door face ** The Gramercy Levers are customized. Refer to page 65 on how to order
64
1-800-727-5477 www.sargentlock.com
REM
Lever
Plain With Raised Band With Metallic Insert With Wood Insert With Santoprenne Insert With Leather Insert
RCM
Part Number
REM RCM RAM RAW RAS RAL
Shank Finish*
Polish Stainless (629) or Satin Stainless (630) Polished Stainless (629) Polished Stainless (629) Polished Stainless (629) or Satin Stainless (630) Polished Stainless (629) or Satin Stainless (630) Polished Stainless (629) or Satin Stainless (630)
Grip Finish
Polish Stainless (629) or Satin Stainless (630) Polish Stainless (629) or Satin Stainless (630) Polished Stainless (629) Polish Stainless (629) or Satin Stainless (630) Polish Stainless (629) or Satin Stainless (630) Polish Stainless (629) or Satin Stainless (630)
* Rose and escutcheon finish is designated by shank finish selected Grip finish must match shank finish
Copyright 1998-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
To order Gramercy Series levers with 80 Series products, see the example below. When specifying finish, use the last two digits of the BHMA standard finish code, i.e. use 29 for polished stainless, BHMA finish 629.
AFF
Select RHR Select from Polished Polished Leather Black or RH, from 80 or satin or satin insert brown LHR, or 80 Series Series stainless stainless LH catalog catalog F RAL 29 BN 29 RH 32D 36"
10-
87
73
12VDC
84"
41"
1-800-727-5477 www.sargentlock.com
65
90641: D 8/30/10
Features
Heavy duty 12 gauge stainless steel in 32D finish Through-bolted for added strength Handed Specify RHR or LHR ADA Compliant #34 Rim Cylinder supplied for 8804
10-9/16" (268mm)
#41 Mortise Cylinder supplied for 8904 Night Latch and Dummy Functions available Available for MD & WD8610, 8710, 8804, 8810, 8904 & 8910 Devices Without protective lip for inactive door
AVT Retrofit Kit works easily with existing product with minor prep modification Order by part number (826, 824, 821 or 827) as determined by product & function below
Designed for exterior doors that require extra security or resistance to vandalism, anti-vandal trim (AVT) plates have an extended lip on the active side of the door to provide extra protection for the latchbolt. A matte plastic coated grip provides a comfortable pull over wide temperature ranges. Fully through-bolted with no exposed exterior fasteners for a cleaner look and increased security.
Description
Cylinder, but No Protective Lip Protective Lip & Cylinder No Protective Lip & No Cylinder Protective Lip & No Cylinder
Application
8804 Mfg after 02-2001 8904; also 8804 Mfg before 02-2001 MD & WD8610, 8710 and 8810 8910
Copyright 1998-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
ET Cover Plate
For all ET functions
3-1/2" (89mm)
Designed for severe windload (Hurricane Code) environments where surface bolts are required (e.g., on inactive doors) Tested to Dade County protocols Listed to UL 10C for use on fire rated door assemblies. Refer to codes for locations where surface bolts are allowed on fire doors All steel construction for maximum strength and heavy duty use Full 3/4" (19mm) square, 12" (305mm) bolt with 1-1/4" (32mm) throw Bright zinc-plated finish Jimmy-resistant design locks bolt automatically when thrown; released by pressing knob toward door while retracting Bolt can be locked in retracted or thrown position Angle (L shaped) and mortise strike with mounting hardware supplied standard
8-3/4" (222mm)
A decorative push bar for vestibule door applications where continuity of design is desired, but no exit device is required. Outside dummy trim available on order. Order as a: 8893 x finish; Specify door width and door stile width when ordering.
This plate is designed to be mounted behind the ET control to cover a stock hollow metal cutout Order as a: 68-0657 x finish
Push rail operates on this rail to simulate active doors. Can be used with dummy trim. Order as a: 8885 x Finish; specify door width and door stile width when ordering. Available with Request-to-Exit (REX) signaling switch; specify 55-8895 x Finish
90641: D 8/30/10
66
1-800-727-5477 www.sargentlock.com
1548S Shown
Specifications
For Doors Finishes Options
Interior doors 18-1/2" up to 48" wide*, 1-3/8" to 1-3/4" thick, as standard see below for correct size. 03, 04, 9, 10, 10B, 10BL, 15, 20D, 26, 26D EN, EB, ED, EAB, EP Powder coat 31- Prefix for use on doors more than 1-3/4" up to 2-1/4" thick. Specify door thickness. 36- Prefix Torx Security machine screws 6 required
How to Order
Specify number, letter suffix, and finish. Example: 1537F x 03 1540 Series furnished with through-bolt and grommet nut for mounting on doors, 1-3/8" to 1-3/4" thick only. For other doors up to 2-1/4" thick, specify thickness when ordering. For center hung pivots, consult factory. Sizing Chart Actual Width of Door 18-1/2" 25" 25-1/8" 32-1/2" 32-5/8" 40" 40-1/8 48" Hold-Open with Stop 1546H 1547H 1548H 1549H Stop Only 1546S 1547S 1548S 1549S Friction Stop/Holder 1546F 1547F 1548F 1549F
UL Classified
SARGENT 1540 Series stops are UL10B & 10C classified by Underwriter Laboratories as Miscellaneous Fire Door Accessories Note: Stops are not rated. The door and frame carry the fire rating
Accessories
SARGENT Manufacturing Company 2007 All rights reserved
Shims Optional 1/4" thick jamb bracket shims for use with frames with blade stops. Machine Screws Order as required by 21-0198 x finish Used with above shims up to 3/4" thick. Four required per overhead. Order by 01-3436 x finish (12-24 x 1-1/4") Standard screw pack 21-2031 x finish
* When using vertical rod exit devices and or surface/flush bolts, use caution in choosing the proper size to ensure compatibility
145 ANGLE BRACKET SHOWN WITH 1540 WITH FLUSH TRANSOM OR RABBETED DOORS
11/01/07
1-800-727-5477 www.sargentlock.com
Conforms to devices outlined in National Fire Protection Agency Standards Nos. 80 and 101 Designed to work with SARGENT door closers Recommended vertical location is on top rail of door within 6" of lock stile edge When applications will not allow wall or floor magnets, consult SARGENTs FireGuard catalog for our line of Electronic Closer Holders Fits standard outlet box
Holding force 35 lbs typical Voltage and Current: 120 VAC, 60 Hz., .020 amp 24 VAC/DC, 60 Hz., .020 amp 12 VDC, .040 amp Finish EN Meets ANSI A156.15 UL UL Listed to U.S. and Canadian safety standards 1" (25mm) extension included standard to increase armature projection to 2-5/8" (67mm)
When de-activated, helps control the spread of fire and smoke by automatically releasing doors from an open position for simultaneous closing Fail-safe device: When electrical power fails, doors will release to close automatically
Wall Mount
1561 Flush Mount
1" (25mm)
2-1/2" (64mm)
2-3/4" (70mm)
1-5/8" (41mm) 1-3/4" (44mm) 2-17/32" (64mm)
4-5/8" (117mm)
1561
1560
Floor Mount
1562 Single Floor Mount
SARGENT Manufacturing Company 2007 All rights reserved
4-3/4" (121mm)
5" (127mm)
1-3/4" (44mm)
1-5/8" (41mm)
5" (127mm)
1-5/8" (41mm)
4-3/4" (121mm)
3-1/8" (79mm)
2-17/32" (64mm)
3-1/8" (79mm)
1562
1563
11/01/07
1-800-727-5477 www.sargentlock.com
Features
Heavy duty 12 gauge stainless steel in 32D finish Through-bolted for added strength Handed Specify RHR or LHR ADA Compliant #34 Rim Cylinder supplied for 8804
10-9/16" (268mm)
#41 Mortise Cylinder supplied for 8904 Night Latch and Dummy Functions available Available for MD & WD8610, 8710, 8804, 8810, 8904 & 8910 Devices Without protective lip for inactive door
AVT Retrofit Kit works easily with existing product with minor prep modification Order by part number (826, 824, 821 or 827) as determined by product & function below
Designed for exterior doors that require extra security or resistance to vandalism, anti-vandal trim (AVT) plates have an extended lip on the active side of the door to provide extra protection for the latchbolt. A matte plastic coated grip provides a comfortable pull over wide temperature ranges. Fully through-bolted with no exposed exterior fasteners for a cleaner look and increased security.
Description
Cylinder, but No Protective Lip Protective Lip & Cylinder No Protective Lip & No Cylinder Protective Lip & No Cylinder
Application
8804 Mfg after 02-2001 8904; also 8804 Mfg before 02-2001 MD & WD8610, 8710 and 8810 8910
Copyright 1998-2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
ET Cover Plate
For all ET functions
3-1/2" (89mm)
Designed for severe windload (Hurricane Code) environments where surface bolts are required (e.g., on inactive doors) Tested to Dade County protocols Listed to UL 10C for use on fire rated door assemblies. Refer to codes for locations where surface bolts are allowed on fire doors All steel construction for maximum strength and heavy duty use Full 3/4" (19mm) square, 12" (305mm) bolt with 1-1/4" (32mm) throw Bright zinc-plated finish Jimmy-resistant design locks bolt automatically when thrown; released by pressing knob toward door while retracting Bolt can be locked in retracted or thrown position Angle (L shaped) and mortise strike with mounting hardware supplied standard Order as a: 988 Surface Bolt
8-3/4" (222mm)
A decorative push bar for vestibule door applications where continuity of design is desired, but no exit device is required. Outside dummy trim available on order. Order as a: 8893 x finish; Specify door width and door stile width when ordering.
The 88-E-PTB is designed to be mounted behind the ET control to cover a stock hollow metal cutout Order as a: 68-0657
Push rail operates on this rail to simulate active doors. Can be used with dummy trim. Order as a: 8885 x Finish; specify door width and door stile width when ordering. Available with Request-to-Exit (REX) signaling switch; specify 55-8895 x Finish
90641: C 1/15/10
66
1-800-727-5477 www.sargentlock.com
Profile Series v.G1.5 Profile Series v.G1.5 Stand-Alone Access Control Products Stand-Alone Access Control Products Accessories Overview for v.G1.5 Profile Series
Overview
1-800-727-5477
www.sargentlock.com
The enhanced v.G1.5 Profile Series of stand-alone access control products combines a broad selection of technologies and new programming features with ANSI/BHMA Grade 1 mechanical locks, housed in a sleek, architecturally pleasing design. Starting with the G1-LU series which offers keypad only to the full-featured G1-TP Series which includes keypad, proximity and RF technology. The locks are programmed via PDA data transfer, all units utilize a battery powered microprocessor based controller with non-volatile memory to preserve user's codes. The Profile Series v.G1.5 is available with SARGENT 8200 series mortise lock, the 10 line cylindrical lock and the 80 series rim and mortise exit devices. These locking devices are UL Listed for use on fire doors. All technologies with the keypad feature offer access codes which may vary from 1 to 6 digits and utilize a master code for keypad programming. Various locking modes allow the operation of the lock to be tailored to each opening and individual user, typical modes include panic, adjustable momentary unlock and passage.
Cylindrical Design
Mortise Design
G1.5-LU (keypad only) configuration of stand-alone access control products are ideal for dormitories, assisted living facilities, hospitals, retailers, apartments and office complexes. Programming is accomplished through the keypad for most basic functions or via SofLink Plus PDP application software. G1.5-PK (proximity/keypad) version of stand-alone access control products offers the highest level of security and flexibility. These products can be programmed via keypad or SofLink Plus w/ SofLink PDP requiring both a code (1-6 digits) and proximity card/fob/tag presentation to gain entry. It can also be programmed for keypad or proximity presentation only. G1.5-PA (proximity only) configuration of access control provides a higher level of security. All programming must be handled through the SofLink Plus w/SofLink PDP application software. This configuration is ideal for high traffic applications where keypad usage is not desirable: universities, laboratories or hospitals. A master Comm Enable proximity card or fob is required to initiate programming of the lock. "G1.5-TU" (keypad and RF technology) series of access control offer the convenience of the keypad along with the RF technology which allows for remote unlocking and locking of the unit. This configuration is ideal where security is a concern (offices and medical clinics). "G1.5-TP" (keypad, proximity and RF technology) series of access control offers all three technologies allowing the lock to be programmed to respond to any of the technologies as needed. "G1.5-TA" (proximity and RF technology) series offers the additional security of eliminating the keypad with the convenience of remote unlocking and locking through the RF technology.
SARGuard Coating
As an integral part of the finish coating, SARGuard lasts for the life of the hardware SARGuard coating permanently suppresses the growth of bacteria, algae, fungus, mold and mildew. It is effective against a broad spectrum of bacteria. Non-toxic and completely safe. The AgION antimicrobial compound is EPA and NSF approved and FDA listed for use in medical and food preparation equipment. Applications: Anywhere there is need for a clean environment (hospitals, laboratories, schools, medical centers, daycare, food processing etc.)
The AgION antimicrobial is not intended as a substitute for good hygiene. Coated products must still be cleaned to insure the surfaces will be free of destructive microbes. SARGENT makes no representations or warranties, express or implied, as to the efficacy of the AgION antimicrobial. A copy of the AgION warranty is available upon request.
Revolutionary finish coating available on all SARGENT product lines, utilizes a silver-based antimicrobial compound from AgION Technologies
Profile Series v.G1.5 Product Stand-Alone Access Control Products Product Features & Comparisons Accessories
Feature Comparisons
Access Stand Alone Unit Keypad Proximity RF Technology Programming Supports all HID Proximity Bit Format SofLink Plus with PDA Directly supports 26, 33 & 34 bit 125 kHZ HID Wiegand bit formats* Supports all 125kHz HID Wiegand (up to 40) bit formats with Enrollment Station Non Volatile Memory Power Requirements Battery Life (Estimate) Batteries Low Battery Indication Hard Power Available Users & Codes # of Users Supported per Lock # of Users Supported by Database Audit Trail Code: Number of Digits Master, Emergency & Supervisory Codes Standard, Extended, Passage Codes Panic, Lockout Codes Comm Unlock, Relock Codes Temporary User Codes Features Real Time Clock with Date & Time Up to 8 Time Zones per Lock Holidays (16 Single & 16 Blocked) Daylight Savings Time Auto Unlock Auto Unlock with First In Adjustable Features Unlock Time Adjustability Audible Keystroke Beep Available Remote Unlocking UL Listed for Fire Doors v.G1.5-LU Yes Yes PDA/Keypad Yes Yes v.G1.5-LU 75,000 cycles 6 "AA" Yes Yes v.G1.5-LU 2,000 20,000 2,000 1 to 6 Digits Yes Yes Yes Yes Yes v.G1.5-LU Yes Yes Yes Yes Yes Yes v.G1.5-LU 1-99 Sec Yes Yes Yes v.G1.5-PK Yes Yes Yes PDA/Keypad Yes Yes Yes Yes Yes v.G1.5-PK 75,000 cycles 6 "AA" Yes Yes v.G1.5-PK 2,000 20,000 2,000 1 to 6 Digits Yes Yes Yes Yes Yes v.G1.5-PK Yes Yes Yes Yes Yes Yes v.G1.5-PK 1-99 Sec Yes Yes Yes v.G1.5-PA Yes Yes PDA Yes Required Yes Yes Yes v.G1.5-PA 75,000 cycles 6 "AA" Yes Yes v.G1.5-PA 2,000 20,000 2,000 Yes Yes Yes Yes Yes v.G1.5-PA Yes Yes Yes Yes Yes Yes v.G1.5-PA 1-99 Sec Yes Yes v.G1.5-TU Yes Yes Yes PDA/Keypad Yes Yes v.G1.5-TU 4-1/2 Mo. 6 "AA" Yes Yes v.G1.5-TU 2,000 20,000 2,000 1 to 6 Digits Yes Yes Yes Yes Yes v.G1.5-TU Yes Yes Yes Yes Yes Yes v.G1.5-TU 1-99 Sec Yes Yes Yes
1-800-727-5477
www.sargentlock.com
v.G1.5-TP Yes Yes Yes Yes PDA/Keypad Yes Yes Yes Yes Yes v.G1.5-TP 4-1/2 Mo. 6 "AA" Yes Yes v.G1.5-TP 2,000 20,000 2,000 1 to 6 Digits Yes Yes Yes Yes Yes v.G1.5-TP Yes Yes Yes Yes Yes Yes v.G1.5-TP 1-99 Sec Yes Yes Yes
v.G1.5-TA Yes Yes Yes PDA Required Yes Yes Yes v.G1.5-TA 4-1/2 Mo. 6 "AA" Yes Yes v.G1.5-TA 2,000 20,000 2,000 Yes Yes Yes Yes Yes v.G1.5-TA Yes Yes Yes Yes Yes Yes v.G1.5-TA 1-99 Sec Yes Yes
Note: Dash ( - ) means either Not Available or Not Applicable * Directly supports 35 bit (Corporate 1000) or other formats with special requirements. Consult factory.
Remote power and request to enter Standard Features available requires wire harness (52-3010) Audit Trail provides parameters such as and hard wiring access granted in, access denied, entry into programming mode, date, time, One master code forced master code user and door information from factory default assigns emergency, supervisory and user codes and allows Low battery indication four chirps after entry when deadbolt is thrown (mortise code entry. Master and emergency code locks) will operate lock after the low battery indication period has passed and user Multiple supervisory codes allow codes no longer operate the lock temporary lockout of selected users, change unlock time duration,request Moisture resistant coating on electronics infrared interrogation output and add Entry of three wrong user codes in user codes succession disables all codes for ten One emergency code allows entry seconds when dead bolt is thrown (mortise UL Listed to Canadian safety standards locks). Unlocks after the low battery Forced and propped door option indication period has passed and user codes no longer operate lock For use on exterior doors with weatherseal gasket, conduit and shroud (optional, Temporary codes by number of uses order separately) (1-500), start-and-stop dates or total days after first use (24 hour specific) Maintained (passage) code unlocks for extended periods of time
Keypad Features LEDs on unit indicate status green indicates unlocked; yellow indicates programming mode Proximity Features Supports all HID 125 KHz Wiegand formats (up to 40 bit) by Keypad Presentation or when using proximity enrollment station ES-G1 with SofLink Plus 5 software Supports 26, 34, & SARGENT 1000 (33 bit) HID formats with SofLink PlusTM version 4.0 or higher software programming
Profile Series v.G1.5 Users) Profile LK Series (100 Stand-Alone AccessSeries (500 Users) Profile LU, PK & PA Control Products Accessories Access Control Products
1-800-727-5477
www.sargentlock.com
SARGENT continues to offer the Profile LK Series (100 Users) and LU, PK & PA Series (500 user) product. The Profile LU, PK & PA products are available and supported The LU (keypad only) configuration of stand-alone access control for facilities with existing Profile Series product (Previous to v.G1 products are ideal for dormitories, assisted living facilities, hospitals, & v.G1.5). retailers, apartments and office complexes. Programming is done through the keypad for most basic functions. The controller will The Profile LU, PK & PA Series software and electronics are retain a total of 500 different user codes varying in length from one not compatible with the Profile Series v.G1 & v.G1.5 product. to six digits. Please consult factory when ordering software for this product, and reference table on page 14 for replacement keypads The PK (proximity/keypad) version of stand-alone access control and controllers. products offers the highest level of security and flexibility. These products can be programmed to require both a code (1-6 digits) and All Profile Series configurations (LK, LU, PK & PA) are available with proximity card/fob/tag presentation to gain entry. It can also be SARGENT 8200 Series Mortise Locks, 10 Line Cylindrical Locks and 80 programmed for keypad or proximity presentation only. Series Rim and Mortise Exit Devices. Available functions are the same as the v.G1.5 as listed on the following pages. The PA (proximity only) configuration of access control provides a higher level of security because all programming must be handled The Profile LK stand-alone access control products are designed through previous version SofLink Plus2.0 w/ SofLink PDP 1.0 for areas that require authorized entry, such as stairwell doors, application software. This configuration is ideal for high traffic meeting rooms, company health clubs, etc. Microprocessor based applications where keypad usage is not desirable: universities, technology with non-volatile solid state memory ensures that codes laboratories or hospitals. A master Comm Enable proximity card or will not be lost even if batteries stop functioning. The controller fob is required to initiate programming of the lock. retains a total of 100 different user codes varying in length from one to six digits. All programming is done through the keypad.
Feature Comparisons
Access LK Stand Alone Unit Yes Keypad Yes Proximity Programming Keypad Supports HID Proximity Bit Format SofLink Plus 2.0 with PDA (serial connection only) "Supports HID Bit Format 26, 33 & 34" Non Volatile Memory Yes Power Requirements LK Battery Life (Estimate) 75,000 Power Supply 6 "AA" Low Battery Indication Yes Hard Wiring Available Yes Users & Codes LK # of Users Supported per Lock 100 # of Users in Database N/A Audit Trail 15 Possible Combinations 1,100,000 Code: Number of Digits 1 to 6 Digits Master Code Yes Emergency Code Yes Supervisory Code Yes One Time User Code Yes Features LK Real Time Clock with Date & Time Up to 8 Time Zones per Lock Holidays (16 Single & 16 Blocked) Daylight Savings Time Auto Unlock Auto Unlock with First In Maintain Unlock Code (Passage) Yes Adjustable Features LK Unlock Time Adjustability 1-99 Sec Audible Keystroke Beep Available Yes Remote Unlocking Yes LU Yes Yes PDA/Keypad Yes Yes LU 75,000 "6 "AA" Yes Yes LU 500 10,000 1000 1,100,000 1 to 6 Digits Yes Yes Yes Yes LU Yes Yes Yes Yes Yes Yes Yes LU 1-99 Sec Yes Yes PK Yes Yes Yes PDA/Keypad Yes Yes Yes Yes PK 75,000 6 "AA" Yes Yes PK PA Yes Yes PDA Yes Required Yes Yes PA 75,000 6 "AA" Yes Yes PA
Bored shown
Mortise shown
* Consult factory
How To Order
Specify Note Example Profile with 10 Line Cylindrical Lock Prefix Signature Cylinder 10Series 10G77 10-10G77 Trim & Tech LK, LU, PK or PA x Lever Design 10-10G77-LKL Finish Specify Finish 10-10G77-LKL-26D Profile with 8200 Series Mortise Lock Prefix XC Key System 11Series/ Function 8276 11-8276 Trim & Tech LK, LU, PK or PA x Lever Design 11-8276-PAJ Finish Specify Finish 11-8276-PKJ-26D Hand Specify Hand 11-8276-PKJ-26D-RH Profile with 80 Series Exit Device Prefix Fire Rated 12Technology LU 12-LU Series/ Function 8877 12-LU8877 Trim ETJ 12-LU8877 x ETJ Hand RHRB 12-LU8877 x ETJ x RHRB Finish Trim/Exit 12-LU8877 x ETJ x RHRB x 26D/32D Door Size 36 12-LU8877 x ETJ x RHRB x 26D/32D x 36
500 500 10,000 10,000 1000 1000 1,100,000 1,100,000 1 to 6 Digits 1 to 6 Digits Yes Yes Yes Yes Yes Yes Yes Yes PK PA Yes Yes Yes Yes Yes Yes Yes PK 1-99 Sec Yes Yes Yes Yes Yes Yes Yes Yes Yes PA 1-99 Sec Yes
Profile Series v.G1.5 Stand-Alone Access Control Products Product Bored Locks & SofLink Features RF Technology
1-800-727-5477
www.sargentlock.com
RF technology offers stand-alone access control enhancement by allowing the user to remotely control the lock by means of a hand-held transmitter (RF Fob). The Profile Lock is easily programmed for three primary RF actuation modes: Passage, Standard or Panic. RF Technology is an additional means of operating the lock by direct keypad code entry or proximity credential presentation.
Outside Escutcheon
Inside Escutcheon
52-2551 RF Fob
To Order
Note: G1.5 products are ordered as G1 products. Specify the desired technology: G1-TU G1-TP G1-TA 2000 Users w/ Keypad only with RF Technology 2000 Users w/ Keypad and Proximity with RF Technology 2000 Users w/ Proximity only and RF Technology
* Operating distance may vary depending on building construction Note: RF Technology (G1-TU, G1-TP, G1-TA) will provide approximately 4-1/2 months of battery life
Profile Series v.G1.5 Stand-Alone Access Control Products 8200 Series Accessories Mortise Locks
1-800-727-5477
www.sargentlock.com
The v.G1.5 Profile Series 8200 motorized mortise lock product has a clean, crisp design and is available in thirteen lever designs and ten hardware finishes. The Profile Series v.G1.5 mortise locks are ideal for business and facility entrances, computer room areas, telephone rooms, health clubs, and child care facilities. The 8200 series mortise lock with dead bolt (G1-8276-LU, G1-8277-PK) is an excellent choice for rest room doors providing privacy when the dead bolt is thrown.
Mechanical Features
Meets ANSI A156.13 Grade 1 requirements Motor driven mortise lock 3/4" stainless steel, anti-friction reversible latch For 1-3/4" (44mm) thick door standard. Consult factory for other thicknesses 1" throw investment cast hardened stainless steel deadbolt Stainless steel non-handed deadlocking latch Handed, easily field reversible without opening lockbody Lever trim through-bolted for increased security and durability Operates with 6 AA batteries (included) Typical 75,000 operations per set of batteries Cylinder override for 8276 and 8278 models, Size 43-standard and removable core (1-3/8" [35mm] length of shell) Not available with SC- or SE- prefixes
Entry Lock Functions 8276 Profile Series Lock with Deadbolt and Cylinder 8277 Profile Series Lock with Deadbolt 8278 Profile Series Lock with Cylinder 8279 Profile Series Lock
Key outside retracts and projects deadbolt and retracts latchbolt Lever inside retracts latchbolt and deadbolt simultaneously when deadbolt is projected Lever outside rigid except when in passage mode or with valid user credential Lever outside locks electrically with deadbolt projected. Master Code & Emergency Code will allow lever outside to retract latchbolt & deadbolt Thumb turn retracts and projects deadbolt Auxiliary deadlatch
Note: Same as 8276 without cylinder Lever inside retracts latchbolt and deadbolt simultaneously when deadbolt is projected Lever outside rigid except when in passage mode or with valid user code Lever outside locks electrically with deadbolt projected. Master Code & Emergency Code will allow lever outside to retract latchbolt & deadbolt Thumb turn retracts and projects deadbolt Auxiliary deadlatch
Key outside retracts latchbolt Lever inside retracts latchbolt Lever outside rigid except when in passage mode or with valid user credential Auxiliary deadlatch Deadlocking latch
Note: Same as 8278 without cylinder Lever inside retracts latchbolt Lever outside rigid except when in passage mode or with valid user credential Auxiliary deadlatch
Inside/Outside Escutcheon
Keys/buttons with double shot mold construction prevents wear Zinc die cast
3/10/06 SARGENT Manufacturing Company 2006
3-3/4" (95mm)
82243 Dorm Room Anti-Lock with Deadbolt and inside lever switch
Note: Same as 8276 with these variations Dorm room application for students using proximity cards Prevents students from locking themselves out of dorm rooms
13-1/2" (343mm)
Operating temperature -40F (-40C) to 135F (57C) LEDs indicate valid/invalid entries Projection at bottom 5/16" (8mm) less lever Projection at top 1-5/8" (41mm)
Outside Shown
Only available with v.G1.5 Technology Requires controller to be configured for Dorm Room application at factory Available with PK and PA versions
Profile Series v.G1.5 Stand-Alone Access Control Products 4293 Wall Prox Unit
1-800-727-5477
www.sargentlock.com
SARGENTs 4293 stand-alone prox reader offers all of the expanded capabilities of our Profile Series v.G1.5 hardware self-contained in a hard-wired reader. The 4293 Wall Prox unit is managed from a personal computer using SofLink Plus Version 4.0 or higher software. The 4293 Wall Prox unit is equipped with IR (infrared) communications which allow the unit to be programmed with SofLink PDP software. In addition, the 4293 Wall Prox unit can be programmed with the units keypad. No separate controller is needed for the 4293 Wall Prox, eliminating the need to run cables from a reader to a controller. The independent unit includes built in HID proximity technology, a keypad, and the controller.
Features
12VDC or 24VDC, 70mA hard-wired Proximity reader 2 Amp main lock relay contact rating 2,000 users and 2,000 audits Database capacity of 20,000 individual users Weather Resistant electronics (gasket included) Supports all HID 125 KHz Wiegand formats (up to 40 bit) by Keypad Presentation or when using proximity enrollment station ES-G1 with SofLink Plus 5 software Supports 26, 34, & SARGENT 1000 (33 bit) HID formats with SofLink PlusTM version 4.0 or higher software programming Separate (auxiliary) 2 amp relay to signal alarm shunt, propped or forced door (must use door status switch) Audible Alert for propped or forced door Can locate proximity antenna up to 10 from keypad/controller Glass mounting kit provided
Dimensions: L: 5-1/4 W: 2-3/4 D: 1-5/8"
Profile Series v.G1.5 Stand-Alone Access Control Products SofLink Plus Access Control Management Software
SofLink Plus w/ SofLink PDP Access Control Management System
1-800-727-5477
www.sargentlock.com
The SofLink Plus w/ SofLink PDP Access Control Management Software allows simple programming and interrogation of the Profile Series v.G1.5 access control products. This software provides the means for fast, convenient assignment of access levels, doors, users, time zones and management of multiple doors with full audit trail capability. Communication between the computer and lock controller is via PDA that allows quick and efficient program transfer and audit trail retrieval.
SofLink PLus 5 provides existing v.G1 and 4293 Wall Prox users with these additional features:
20,000 users (up from 10,000) Use of two new Palm PDAs (Zire 31 & Zire 72) Access the database(s) from multiple PC locations New, more detailed reporting Auto Backup prompts "User-Friendly" System Setup Task List Guide Enable/Disable user capability Use of proximity Enrollment Station "Forced" Master Code (from Factory Default)
CD-SLP5
v.G1.5 controllers WITH SofLink Plus 5 software provide these additional features
First-IN Auto-Unlock by specified user Temporary Codes by number of uses (1-500), start and stop dates or total days after first use (24 hour specific) Forced Master Code (from Factory Default) Multiple Supervisory users
Catalog #PDA-Z31 - Palm Zire 31 PDA Works with SofLink Plus 5.0 and above.
User friendly help feature Extensive report generating feature Directly supports 26, 33 and 34 HID 125kHz Wiegand bit formats or all (up to 40 bit) formats when using the proximity Enrollment Station. For directly supporting 35 Bit Corporate 1000 Format or other formats, consult factory Designed for operation with Personal Digital Assistant (PDA) running Palm OS PDA provides convenient (wireless) means of transferring door information to and from lock using SofLink Plus w/ SofLink PDP software Capable of up/down loading door information for up to 50 doors NOTE: Number of stored files is dependent on the amount of non-related SofLink Plus w/ SofLink PDP software applications and data (e-mail messages, address data, to do items, memos, etc.) loaded on the PDA. Five additional compatible PDAs Access the database(s) from multiple PC locations New, more detailed reporting Auto Backup prompts "User-Friendly" System Setup Task List Guide Enable/Disable user capability Auto Unlock with or without first in authorization First-in Auto-Unlock by specified users* Temporary Codes by number of uses (1-500), start-and-stop dates or total days after first use (24 hour specific)* "Forced" Master Code (from Factory Default)* Multiple Supervisory users* Allows customized access levels managed at PC User name import from an external database Easy to follow data entry Real time clock with date and time Eight different time zones per lock Holidays (16 single days and 16 blocked) Forced/Propped Door log events - harness required (option) Daylight savings time
v.G1.5 controllers WITHOUT SofLink Plus 5 software provide these additional features
Forced Master Code (from Factory Default) Multiple Supervisory users
Hardware Requirements
Windows 2000/XP (to include all subsets) VGA monitor CD ROM drive Instruction Manual included Personal Digital Assistant (PDA)
Catalog #PDA-Z21 - Palm Zire 21 PDA Works with SofLink Plus 3.0 and above.
Profile Series v.G1.5 Stand-Alone Access Control Products Access Credentials Accessories
Credential Features
26 to 39 bit Wiegand format available (Consult factory for details) Provides higher level of security when combined with keypad operation HID-based proximity cards, fobs or tags Allows integration into existing facilities with HID-based technology HID technology allows Access Control software to read other formats provided site code is known. For a higher level of security, custom cards, fobs or tags with unique site codes are available. Consult factory.
1-800-727-5477
www.sargentlock.com
SARGENT standard credentials are 26 Bit Wiegand format, Site Code 20 and Proximity ID assigned by SARGENT Custom credentials available with customer assigned Site Code and Prox ID#'s
MicroProx Tag
The MicroProx Tag is a coin-sized (disk-shaped) transponder that provides the ability to add HID proximity technology to a device. The MicroProx Tag has an adhesive backing which allows it to be secured to any non-metallic object. Easily Secured To: Employee badges PDAs Magnetic stripe cards Cell phones 26 Bit Format, HID Coded Wiegand Output 125 kHz Proximity ID# marked on each Tag Gray color with HID Logo Dimensions: 1.285" Dia. x 0.070" (32.6mm x 1.78mm) Two Versions available: Catalog # MPT - Site Code 20 - Proximity ID#s determined & controlled by SARGENT - MicroProx Tag ordered individually*** - Min. order is 25 MicroProx Tag Catalog # MPT-C - Site Code - requested by customer - Proximity ID#'s requested by customer - MicroProx Tag ordered individually*** - MicroProx Tag with custom site code, consult factory for minimum quantities NOTE: The MicroProx Tag should be attached to magnetic stripe cards so that contact with the magnetic card reader is avoided.
PF SARGENT ProxKey II
Site Code 20 Proximity ID#s determined & controlled by SARGENT 26 Bit Format, HID Coded Wiegand Output 125 kHz Dimensions: 1-29/32" x 29/32" x 11/32" (48mm x 23mm x 9mm) Includes Keyring SARGENT ProxKey II ordered individually*** (Min order is 25 ProxKey II) Catalog # PF for SARGENT ProxKey II
DuoProx Card
Multiple Technology Proximity Cards DuoProx dual technology - proximity & magnetic stripe DuoProx cards with unique site codes for higher level of security (SARGENT 1000) are available Contact Factory for specifications, options and pricing Cards ordered individually*** (Min order is 100 Cards)
1000
ProxCard II, DuoProx, Micro-Prox and ProxKey II are trademarks of HID Corporation 3/10/06 SARGENT Manufacturing Company 2006
*** Products are ordered individually, Ordered Quantity is the number of individual items to be shipped. If a Qty of 25 is ordered 25 individual items will be shipped (Note: Min Order Requirements)
Note 1: Profile Series v.G1.5 will support all HID bit formats when proximity credentials are programmed directly into keypad (Presentation Method) Note 2: SofLink Plus w/ SofLink PDP software directly supports 26, 33 and 34 HID 125 kHz Wiegand bit formats or all (up to 40 bit) when using the Enrollment Station, ES-G1. To directly support other formats (such as 35 bit HID Corporate 1000 format), consult factory.
10
Profile Series v.G1.5 Stand-Alone Access Control Products Accessories SARGENT BioFob Security Device
1-800-727-5477
www.sargentlock.com
The BioFob Security Device is the first handheld, wireless, biometric device providing both physical and logical access. This self-contained unit performs fingerprint sensing, image processing, storage and matching to activate the RFID (HID or Indala) and Bluetooth signals. These signals unlock SARGENTs Profile Series Locks, existing HID or Indala readers and encrypted computer systems. BioFob is the perfect biometric solution for your existing security system.
BioFob Specifications
Power Interfaces Battery type: CR2 lithium cell (included) Battery life: Approximately 1 year; 5 operations per day. User interaction: 3 LEDs (red, yellow, green), 1 push button (power) RF options: Low-frequency RFID, HID and Indala compatible (125 kHz) and Bluetooth (2.4 GHz) Operating temperature: +14 F to +140 F; (-10 C to +60 C) Storage temperature: -40 F to +185 F; (-40 C to +85 C) Operating humidity: 90% noncondensing
Environment
System Requirements for the Enrollment Station Software and Bluetooth Adapter
Minimum software and hardware requirements: Microsoft Windows 2000 or Microsoft Windows XP 64 megabytes of RAM 20 megabytes of available hard drive space One available USB port 800x600 minimum resolution
A configuration module (also known as a dongle) attaches to the computer's USB port. It is required to encode an uncoded Biofob (BF4) or recode any BioFob with a Site Code & Proximity ID. The configuration modules are available with either HID or Indala proximity ID's with either 25 or 100 proximity ID's per module.
The SARGENT BioFob was developed in partnership with Privaris, Inc., a technology company dedicated to solving security and privacy concerns for government and commercial applications.
All BioFobs and modules are 26 Bit Format. For other formats, please consult factory.
11
Profile Series v.G1.5 Stand-Alone Access Control Products Accessories SARGENT BioFob Security Device
General Information
1-800-727-5477
www.sargentlock.com
The Proximity ID# is assigned to a Proximity Credential (e.g., BioFob). This number identifies a Proximity Credential to a user within a given Site Code. A Site Code is a number established by either SARGENT (e.g., BF1 BioFob) or the end-user. The Site Code, established by the Bit Format, is a number between 1 and 255 for a 26 Bit Format configuration. The Site Code assigned to a group of proximity control products (e.g., Profile Series) and Proximity Credentials (BioFob, etc.) must be identical for the two to interact. Proximity ID#'s should not be used more than once within a Site Code for security reasons. The Bit Format, part of the coding configuration within a Proximity Credential (BioFob) is established and can only be changed by the manufacturer. A 26 Bit Format of a Proximity Credential (BioFob) has 65,535 ID#s available. The 26 Bit Format for Site Codes and Proximity ID#'s creates over 16.5 million possible Site Codes/ID#s per BioFob.
How to Order
Qty 1 BF1 Qty 1 BF2 Site Code XXX Prox ID # XXXXX Qty 1 BF3 Site Code XXX Prox ID # XXXXX Qty 1 BF4
How to Order
Qty 1 BFES
BFES
BF6
Qty 1
BF6
Includes:
Customer defined - 1 Site Code - 25 HID Proximity ID#s Customer defined - 1 Site Code - 100 HID Proximity ID#s Customer defined - 1 Site Code - 25 Indala Proximity ID#s Customer defined - 1 Site Code - 100 Indala Proximity ID#s
How to Order
Qty 1 BF7 Site Code XXX Prox ID #s XXXXX-XXXXX Qty 1 BF8 Site Code XXX Prox ID #s XXXXX-XXXXX Qty 1 BF9 Site Code XXX Prox ID #s XXXXX-XXXXX Qty 1 BF10 Site Code XXX Prox ID #s XXXXX-XXXXX
BF7 BF8
3/10/06 SARGENT Manufacturing Company 2006
BF9 BF10
Note: All BioFobs and Configuration Modules are 26 Bit Format. For other formats, consult factory.
12
1-800-727-5477
www.sargentlock.com
52-0258
Cable Assembly-Power Supply to Power Transfer 12' (3.6m) shielded cable from the power to the power supply
52-2498
9 VDC, 700 ma Power Supply circuit board Replacement circuit board assembly
Trim Kits are the motorized exit trims that are necessary to be used with the Profile Upgrade Kits to convert an existing exit device. Trim Kit P/N 777-8 778-8 777 778 Description 8800 Series Rim Exit Device w/ Cylinder Override 8800 Series Rim Exit Device w/o Cylinder Override 8900 Series Mortise w/ Cylinder Override 8900 Series Mortise Exit w/o Cylinder Override
13
1-800-727-5477
www.sargentlock.com
Note: Replacing existing G1 controllers with G1.5 controllers provides the following new features: "Forced" Master Code change from factory default Multiple Supervisory users First-in Auto-Unlock by specified users (SofLinkPlus 5.0 required) Temporary Codes by number of uses (1-500), start-and-stop dates or total days after first uses (SofLinkPlus 5.0 required) Dorm Room Anti-Lock Product
4293
52-2704
52-2706
Weatherseal Gasketing
Provides sealing between outside escutcheon and door for exterior applications Gasketing (included) recommended for non-fire rated exterior applications
82-0500
68-1400
52-0263
10-0469
52-2847 Conduit
Provides weather protection inside of door Constructed of durable ABS material For non-fire rated exterior applications only Included with product
14
Profile Series v.G1.5 Stand-Alone Access Control Products Lever Trim Designs
1-800-727-5477
www.sargentlock.com
Profile Series v.G1.5 products are available with lever designs identical to levers offered on mechanical hardware to introduce uniformity throughout a facility. Lever projection from door surface varies with lock type.
v.G1.5 8200 Mortise Levers and v.G1.5 80 Series ET Levers A Lever Design
Lever: A-Solid forged or cast Must specify hand when ordering
P Lever Design
Lever: P-Solid forged or cast
J Lever Design
Lever: JSolid Cast
B Lever Design
Lever: B-Solid forged or cast
W Lever Design
Lever: W-Solid bar stock
L Lever Design
Lever: LSolid Cast
E Lever Design
Lever: E-Solid forged or cast
Coastal Series for v.G1.5 8200 Mortise Locks and 80 Series Exits
Solid Cast Brass
F Lever Design
Lever: F-Solid forged or cast
G - Gulfport
Must specify hand when ordering
J Lever Design
Lever: J-Solid bar stock
R - Rockport
L Lever Design
Lever: L-Solid forged or cast
S - Sanibel
Must specify hand when ordering
Y - Yarmouth
3/10/06 SARGENT Manufacturing Company 2006
Y - Yarmouth
Must specify hand when ordering
15
1-800-727-5477
www.sargentlock.com
Aventura Series
MA
Rialto Series
MO
MD
MB
ML
MJ
ME
Odon Series
MN
MP
MF
MH MG
MR
MS
MT MU
MM
3/10/06 SARGENT Manufacturing Company 2006
MV
16
1-800-727-5477
www.sargentlock.com
17
Profile Series v.G1.5 Stand-Alone Access Control Products Finishes, Handing, How to Order & Shipping Information
How To Order
Specify Bored Prefix Series Trim Finish Mortise Prefix Series/Function Trim Finish Hand Exit Prefix Technology Series/Function Trim Hand Finish Door Size Note Signature Cylinder 10G77 Technology & Lever Design Specify Finish Signature Cylinder 8276 Technology & Lever Design Specify Finish Specify Hand Fire Rated LU 8877 ETJ RHRB Trim/Exit 36" Example 10 10-10G77 10-G1-10G77-PKL 10-G1-10G77-PKL-26D 10 10-8276 10-G1-8276-PAJ 10-G1-8276-PAJ-26D 10-G1-8276-PAJ-26D-RH 12 12-G1-LU 12-G1-LU8877 12-G1-LU8877 x ETJ 12-G1-LU8877 x ETJ x RHRB 12-G1-LU8877 x ETJ x RHRB x 26D/32D 12-G1-LU8877 x ETJ x RHRB x 26D/32D x 36" 10 10-82243 10-G1-82243-PKL 10-G1-82243-PKL-26D 10-G1-82243-PKL-26D-RH
1-800-727-5477
www.sargentlock.com
Handing
LH
RH
Dorm Room Anti-Lock (Mortise Only) Prefix Signature Cylinder Series/Function 82243 Trim Technology & Lever Design Finish Specify Finish Hand Specify Hand
Shipping Information
Lock G1-8276-PK x lever trim (with cylinder) G1-8277-PK x lever trim (no cylinder) G1-8278-PK x lever trim (with cylinder no deadbolt) G1-8279-PK x lever trim (w/o cylinder no deadbolt) G1-LU8877 G1-PA8977 G1-10G77-PKL Shipping Weight 11.2 lbs (5.1kg) 10.7 lbs (4.9kg) 11.2 lbs (5.1kg) 10.7 lbs (4.9kg) 21.0 lbs (9.5kg) 23.0 lbs (10.4kg) 10.7 lbs (4.9kg) Pc. Count/Carton 1/carton 1/carton 1/carton 1/carton 1/carton 1/carton 1/carton
Finishes
SARGENT US3 US4 US9 US10 US10B 10BL US15 20D US26 US26D Description Polished brass Satin brass Polished bronze Satin bronze, clear powder coat Oxidized satin bronze oil rubbed Oxidized satin bronze, clear powder coat Satin nickel, clear coated Dark statuary bronze, clear powder coat Polished chrome Satin chrome ANSI/BHMA 605 606 611 612 613 619 625 626
3/10/06 SARGENT Manufacturing Company 2006
19
T-Zone
OL Design
Rose: O - Wrought Lever: L - Cast
2-3/4" (70mm)
4-15/16" (125mm)
EB Design
Rose: E - Wrought Lever: B - Cast
1" (25mm) 2-1/8" (54mm)
2-3/4" (70mm)
+/-1-13/16" (46mm)
2-1/4" (57mm)
LJ Design
Rose: L - Wrought Lever: J - Cast
2-3/4" (70mm) +/-1/2" (13mm) 1-1/8" (29mm)
5-5/16" (135mm)
BP Design
Copyright 2008 SARGENT Manufacturing. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.
Note: Any rose and lever on this page can be combined to suit individual taste. Note: Lever projections shown are for 1-3/4" (44mm) doors and will vary by door thickness.
3/15/08
1-800-727-5477 www.sargentlock.com