Professional Documents
Culture Documents
Service Manual
-2 -
MODEL: LCT-32HSSTP
-3 -
CONTENTS
SAFE PRECAUTION .............................................................................................................................. 4 BLOCK DIAGRAM ................................................................................................................................ 5 FUNCTION OF CONJUNCTION........................................................................................................... 6 SIGNAL DIAGRAM ............................................................................................................................... 9 POWER DIAGRAM .............................................................................................................................. 10 TROUBLESHOOTING ......................................................................................................................... 11 WALL-MOUNTING BRACKET INSTALLATION GUIDE................................................................ 14 CIRCUIT DIAGRAM ............................................................................................................................ 17 PART LIST............................................................................................................................................. 26
-4 -
SAFETY PRECAUTION
WARNING:
Service should not be attempted by anyone unfamiliar with the necessary precaution on this receiver. The following are the necessary precautions to be observed before servicing this chassis. 1. When replacing a chassis in the cabinet, always be certain that all the protective devices are put back in place, such as: non-metallic control knobs, insulating covers, shields, isolation resistor-capacitor network etc. 2. 3. 4. 5. When replacing parts or circuit boards, disconnect the power cord. When replacing a high wattage resistor (oxide metal film resistor) on the circuit board, keep the resistor 10mm (1/2in) away from circuit board. Connection wires must be kept away from components with high voltage or high temperature. If any fuse in this TV receiver is blown, replace it with the FUSE specified in the chassis parts list.
-5 -
BLOCK DIAGRAM
PANEL
CN801
XP501
XP511
XP7
XP3
CN902
MAIN BOARD
POWER BOARD
-6 -
FUNCTION OF CONJUNCTION
CN801---XP501 ITEM 1 2 3 4 5 6 7 8 9 NAME 5V PS GND 14V PGND 12V 12V GND GND FOR PANEL POWER FOR POWER OFF GND FOR AUDIO POWER AUDIO GND FOR MAIN POWER FOR MAIN POWER FOR MAIN GND FOR MAIN GND CN902---XP4 ITEM 1 2 3 4 5 6 7 NAME GND 14V 14V GND 12V GND 5.0V FOR AUDIO GND FOR AUDIO POWER FOR AUDIO POWER FOR AUDIO GND FOR AUDIO POWER FOR AUDIO GND TUNNER POWER CN901---XP2 ITEM 1 2 3 4 5 6 7 8 NAME ADC1 ADC2 GND MUTE RESET GND SDA SCL FUNCTION FOR SCART1 AUTO IDENTIFY FOR SCART1 AUTO IDENTIFY GND AUDIO MUTE MSP3410 RESET GND FOR SERIAL DATA FOR SERIAL CLOCK FUNCTION FUNCTION
-7 -
CN901---XP2 ITEM 1 2 3 4 5 6 7 8 9 10 11 12 NAME GND CVBS GND GREEN GND RED GND FB GND BLUE GND AVOUT GND FOR TV'S CVBS SIGNAL GND FOR SCART GREEN GND FOR SCART RED GND FOR FAST BLANK GND FOR SCART BLUE GDN FOR MONITOR OUT CN903---XP1 ITEM 1 2 3 4 5 6 NAME AV1-IN GND AV2-IN GND S-CIN GND FOR VIDEO1 IN GND FOR VIDEO2 IN GND FOR C-IN GND FUNCTION FUNCTION
-8 -
P40 ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 NAME PWM APWM ON/OFF GND RX0RX0+ GND RX1RX1+ GND RX2RX2+ GND RCLKRCLK+ GND RX3RX3+ GND N.C. N.C. N.C. GND GND GND Panel_power Panel_power Panel_power Panel_power Inverter_power Module power Module power Module power Module power Inverter logic power LVDS signal LVDS signal LVDS clock signal LVDS clock signal LVDS signal LVDS signal LVDS signal LVDS signal LVDS signal LVDS signal PWM Dimming Analog PWM dimming Backlight On~Off: 2.4-5.0V 0-1V On Off FUNCTION
-9 -
SIGNAL DIAGRAM
SCART1 A1
N1 MSP3410
N4 TDA7266B
SPEAKER SPEAKER
N5 LM358
EARPHONE
SCART2
TUNER
U400 VPC3230
U500 GM1501
PANEL
U401 PI5V330
-10 -
POWER DIAGRAM
U0 82 L18 M06 U0 83 L11-. T1718 U0 50 G10 M51 U0 40 VC20 P33
C81 N0 1 2 3 4 5 6 7 8 9 GD N GD N 1V 2 PN GD 1V 4 GD N S W 5 V
U0 +V 80 5 L27 M56
U1 80 L11-. T1733
U0 85 L11-. T1725
Mi bad an or
1V 4
U0 92 IF34 R71
N0 31 TA26 D76B
1V 2
U0 91 L70 M89
9 V
N0 32 C45 D02
Ivre_oi_oe netrlgcpwr
U0 86
N0 33 NW17 J13
Pnlpwr ae_oe
N0 34 L38 M5
1 2 3 4 5 6 7
10 2V 10 2V 10 2V GD N GD N GD N GD N
LD C
-11 -
TROUBLESHOOTING
NO PICTURE
CN801 PIN6:12V
NO
YES
FB703 PIN1:5V
NO
REPLACE U800
YES
U806 PIN5,6,7,8:5
NO
REPLACE U806
YES
U802 PIN2:3.3V
NO
REPLACE U802
YES
NO
YES
NO
REPLACE U402
YES
NO
REPLACE U402
YES
OK
-12 -
NO TELETEXT
U809(2.5V)
YES
NO
REPLACE FB409FB410FB411FB412
YES
REPLACEU70 3,U704,U706
-13 -
NO SOUND
YES
A1 PIN4
NO
REPLACE A1
YES
N1 PIN27, PIN28
NO
REPLACE N1
YES
NO
REPLACE N4
YES
OK
NO
N4 PIN7(4.5)
CHECK V3 V4
-14 -
Wall-mounting Installation Steps: 1. 2. 3. 4. Take out the bracket form the package and check if there are serious defects (e.g. infirm juncture). Adjust the bracket to the desired angle. Use bolt 7 to adjust the angle by meeting holes of column beam2 and holes of lever 4. Drill locating holes in the specified dimension in a vertical wall of concrete or brick. The hole size should be 11mm. The hole depth should accommodate the expanding tube of the bolt. Fix the bolts into the drilled holes in step3, and then cover each bolt with a metal washer. Meet the four mounting holes in the bracket with the four bolts in the wall, cover each bolt with a metal washer, then fasten with a screw nut. Check its rigidity by pulling the bracket. 5. 6. Fix the fixture disk to the back cover of the TV using six M4x20 bolts. Wall-mount the TV by putting the six-fixture disk into the six mounting holes A.
-15 -
-16 -
-17 -
CIRCUIT DIAGRAM
-18 -
-19 -
-20 -
-21 -
-22 -
-23 -
-24 -
-25 -
-26 -
PART LIST
CODE
103246 103247 101814 101808 1011691 1020374 1005288 1004899 1004693 1013110 1013122 1020322 101227 1020333 1020311 1020323 1019700 Digital board Tuner board Front control board Switch board LCD panel Remote control Inverter connector Cable to panel AC cord Speaker Speaker Uesr's manual Back cover Front encloser Rating label Carton box Signal cord
DESRIPTION
RSAG2.908.452 RSAG2.908.451 RSAG2.908.337 RSAG2.908.313 LTA320W1-L02 HYDFSR-A026AK SP030623770R1 SP030910890 PHP-206+PHS-301 YD83E-10W8R-B YDG50-10W8R-A IES040937 WTG6.170.071 RSAG8.074.096\W9+B2\SYN135 E/RSR8.807.1377 E/RSR8.865.1511 SCART-S-2.0