Professional Documents
Culture Documents
000 1 2 3 4 5 6 7 8 9
10 1 Bank-Systems Lambda control learning value partial load Lambda control learning value idle Lambda control Idle Air Control Valve learning value Idle Air Control Valve Throttle valve potentiometer Voltage
10 2 Bank-Systems Lambda adaptation (add) Bank 2 Lambda adaptation (add) Bank 1 Lambda control Bank 2 Lambda control Bank 1 Idle Air Control Valve learning value Idle Air Control Throttle valve angle
001
[1/min]
closed
Lambdacontrol: OK Idle switch closed A/C compr. OFF Cat temp. reached no DTC stored in
memory
002
Load [%]
Systems with Mass Airflow Sensor Mean injection time Air mass [ms] [g/s] Systems with intake manifold pressure sensor Mean injection time Intake manifold pressure [ms] [mbar] Systems with Mass Airflow Sensor Throttle valve angle Ignition angle (actual) (Potentiometer) [%] [KW] Systems with intake manifold pressure sensor Throttle valve angle Ignition angle (actual) (Potentiometer) [%] [KW] Cooling temperature [C] Speed [km/h] Intake air temperature [C] Operating condition Text (Idle, partial load, full load, SA, BA)1[1]
002
003
003
General RPM [1/min] Intake manifold pressure [mbar] Voltage [V] Load [%]
004
005
006
Intake air temperature Altitude correction2[2] [C] Intake manifold pressure Mass Airflow Sensor [mbar] Condition vacuum pump for brake Pump ON / Pump OFF [%] Pressure bake booster
007
3[1] Idle, partial load, full load, deceleration fuel shut-off, acceleration enrichment 4[2] Relative to reference level; 0% = 0 m; -100% = 10000 m
011
Intake air temperature Ignition angle (actual) [C] [KW] No. of crankshaft tooth at camshaft flank low->high [xx] No. of crankshaft tooth at camshaft flank low->high [xx]
012
Last [%]
015
Misfire recognition Counter Cyl.. 1 [n] Misfire recognition Counter Cyl.. 4 [n] Misfire recognition Counter Cyl.. 7 [n]
Misfire recognition Text: activated / locked Misfire recognition Text: activated / locked Misfire recognition Text
016
017
018
019
activated / locked Load / RPM window misfire recognition (if no misfire recognized: 0 at all positions) Lower RPM limit Upper RPM limit Lower RPM limit Upper RPM limit [n] [n] [%] [%] Misfire recognition Counter Cyl. 10 Counter Cyl. 11 Counter Cyl. 12 Misfire recognition [n] [n] [n] Text: activated / locked
021
022
023
024
025
026
027
028
RPM Last Retard Cyl. 3 [1/min] [%] [KW] Knock control RPM Last Retard Cyl. 5 [1/min] [%] [KW] Knock control RPM Last Retard Cyl. 7 [1/min] [%] [KW] Knock control, knock sensor voltage (amplifier factor included) Cyl.. 1 Cyl.. 2 Cyl.. 3 [V] [V] [V] Knock control, knock sensor voltage (amplifier factor included) Cyl.. 5 Cyl.. 6 Cyl.. 7 [V] [V] [V] Test knock sensor, short trip RPM Load Coolant temperature [1/min] [%] [C]
Retard Cyl. 4 [KW] Retard Cyl. 6 [KW] Retard Cyl. 8 [KW] Cyl.. 4 [V] Cyl.. 8 [V] Result Text: Test ON /Test OFF/ Sys. OK / Sys. not OK
029
ON ON Oxygen sensor voltage Bank 1, sensor 1 Bank 1, sensor 2 [V] [V] Oxygen sensor voltage Bank 1, sensor 1 Bank 1, sensor 2 [V] [V] Linear oxygen sensors Lambda actual value Lambda specified value Bank 1 Bank 1 [] [] Linear oxygen sensors Lambda actual value Lambda specified value Bank 1 Bank 1 [] [] Oxygen sensors learning values (maximum value) Bank 1, sensor 1, idle Bank 1, sensor 1, partial load [%] [%] Oxygen sensors learning values (maximum value) Bank 1, sensor 1, idle Bank 1, sensor 1, partial load
031
031
031
032
2- bank systems Bank 2, sensor 1, idle [%] Bank 2, sensor 1, partial load [%] 1- bank systems
032
[%] 033 Lambda control value Bank 1, control value [%] 033 Lambda control value Bank 1, control value [%] 033
[%] Bank 1, Oxygen sensor voltage [V] Bank 1, Oxygen sensor voltage [V] Bank 2, control value 2- bank systems Bank 2, sensor voltage before cat. converter of a broad band sensor [V] Bank 2, control value [%] 2- bank systems Bank 2, knock sensor voltage [V] 1- bank systems
Linear oxygen sensor control value Bank 1, control value Bank 1, sensor voltage before cat. converter of a broad band sensor [%] [V]
[%]
034
034
035
035
Oxygen sensor aging test Bank 1 or Bank 3 before catalytic converter, short trip RPM Exhaust gas / cat. Length of period Result converter temperature [1/min] [C] [s] Text: Test ON/Test OFF/ B1-S1 OK/B1-S1 not OK or: B3-S1 OK /B3-S1 not OK Oxygen sensor aging test Bank 1 or Bank 3 before cat. converter for linear oxygen sensors. short trip RPM Exhaust gas / cat. Dynamic factor Result converter temperature [1/min] [C] [] Text: Test ON/Test OFF/ B1-S1 OK/B1-S1 not OK or B3-S1 OK ./B3-S1 not OK Oxygen sensor aging test Bank 2 or Bank 4 2-bank systems before cat. converter, short trip RPM Exhaust gas / cat. Length of period Result converter temperature [1/min] [C] [s] Text: Test ON/Test OFF/ B2-S1 OK/B2-S1 not OK or B4-S1 OK/B4-S1 not OK Oxygen sensor aging test Bank 2 or Bank 4 2- bank systems before cat. converter for linear oxygen sensors, short trip RPM Exhaust gas / cat. Dynamic factor Result converter temperature [1/min] [C] [] Text: Test ON/Test OFF/ B2-S1 OK /B2-S1 not
035 036
Oxygen sensor aging test Bank 2 before cat. converter Oxygen sensor readiness after cat. converter, short trip Bank 1, sensor 2 Result Sensor voltage Text: Test ON/Test OFF/ B1-S2 OK/B1-S2 not OK or: B3-S2 OK/B3-S2 not OK Oxygen sensor readiness after cat. converter, short trip Bank 1, sensor 2 Result Sensor voltage Text: Test ON/Test OFF/ B1-S2 OK./B1-S2 not OK. Oxygen sensors, short trip Last Bank 1: Oxygen sensor voltage after cat. converter [%] [V]
OK or: B4-S1 OK/B4-S1 not OK 1- bank systems 2- bank systems Bank 2, sensor 2 Sensor voltage Result Text: Test ON/Test OFF/ B2-S2 OK/B2-S2 not OK or: B4-S2 OK/B4-S2 not OK 1- bank systems
036
037
Bank 1: TV shift
Result
[ms]
037
Linear oxygen sensors, short trip Last Bank 1: Oxygen sensor voltage after cat. converter [%] [V]
Bank 1: ( Lambda
[]
038
Oxygen sensors, short trip Last Bank 2: Oxygen sensor voltage after cat. converter [%] [V]
Bank 2: TV shift
Text: Test ON/Test OFF/ Sys. OK/Sys. not OK 2- bank systems Result
[ms]
038
Linear oxygen sensors, short trip Last Bank 2: Oxygen sensor voltage after cat. converter [%] [V]
Bank 2: ( Lambda
Text: Test ON/Test OFF/ Sys OK/Sys. not OK 2- bank systems Result
[]
038 039
Sensor exchange after cat. converter short trip Air mass Bank 1: sensor Bank 2 sensor voltage Result voltage
[g/s]
[V]
[V]
040
Condition Text: Heater before cat. ON/ Heater before cat. OFF
Condition Text: Heater before cat. ON/ Heater before cat. OFF 1- bank systems 1- bank systems Condition Text: Heater after cat. ON/ Heater after cat. OFF
Not used 041 Oxygen sensor heater Resistor Condition or duty Resistors cycle Bank 1, sensor 1 Text: Bank 1, Sensor 2 Heater before cat. ON/ Heater before [] [] cat. OFF or: sensor 1 [%] Oxygen sensor heaters, separate wires of heaters Resistor Condition or duty Resistors cycle Bank 2, Sensor 1 Text: Bank 2, Sensor 2 Heater before cat. ON/ Heater before [] [] cat. OFF or: Sensor 1 [%] Oxygen sensor ageing after cat. converter, linear oxygen sensors, short trip RPM Exhaust gas / cat. Oxygen sensor converter temperature voltage [U/min] [C] [V]
042
2- bank systems Condition Text: Heater after cat. ON/ Heater after cat. OFF
043
Bank 1 Result Text: Test ON/Test OFF/ B1-S2 OK/B1-S2 not OK Or: B3-S2 OK/B3-S2 not OK Bank 2 Result Text : Test ON/Test OFF/ B2-S2 OK /B2-S2 not OK Or: B4-S2 OK/B4-S2 not OK 1-bank systems
044
Oxygen sensor ageing after cat. converter, short trip RPM Exhaust gas / cat. Oxygen sensor converter temperature voltage [U/min] [C] [V]
044 045 NOx memory cat. converter Bank 1, short trip Factor memory entry Result NOx Text:
NOx memory cat. converter Bank 2 Factor memory entry Result NOx Text:
046
Test ON/Test OFF/ Sys. OK/Sys. not OK Cat. converter conversion test Bank 1 or Bank 3, short trip RPM Cat. converter Measuring value cat. temperature Converter conversion [1/min] [C]
Test ON/Test OFF/ Sys. OK/Sys. not OK Result Text: Test ON/Test OFF/ Cat B1 OK/ Cat B1 not OK or: Cat B3 OK/ Cat B3 not OK 2-Bank-Systems Result Text: Test ON/Test OFF/ Cat B2 OK/ Cat B2 not OK or: Cat B4 OK/ Cat B4 not OK 1-Bank-Systems
047
Cat. converter conversion test Bank 2 or Bank 4, short trip RPM Cat. converter Measuring value cat. temperature Converter conversion [1/min] [C]
047 048
Cat. converter conversion test Bank 2 Not used Thermal cat. converter diagnosis Bank 1, short trip Operating system Number of test steps BDE [-] [-]
Exothermal Result temperature increase [K] Text: Test ON/Test OFF/ Sys. OK/Sys. not OK
049
Thermal cat. converter diagnosis Bank 2, short trip Operating system Number of test steps BDE [-] [-]
Exothermal Result temperature increase [K] Text: Test ON/Test OFF/ Sys. OK/Sys. not OK
050
RPM increase RPM actual value [1/min] RPM specified value [1/min]
051
Driving range (only for Supply voltage automatic transmission) [V] 0-6
052
RPM increase
052
(Idle, driving ranges 1-6) Systems without separation for rear window defroster /A/C readiness Not used Systems with separation for rear window defroster /A/C readiness RPM (specified value) A/C readiness Rear window defroster [1/min] Text Text
053
054
054
055
ON/OFF ON/OFF RPM increase based on generator load RPM (actual value) RPM (specified value) Voltage Generator load [1/min] [1/min] [V] [%] Closed throttle position switch RPM Operating conditions Throttle valve angle Throttle valve angle (Potentiometer) (Potentiometer) [1/min] (LL, TL, VL, SA, BA) [%] [%] Closed throttle position switch for E-Gas-systems RPM Operating conditions Sensor 1 for Throttle valve angle accelerator pedal (Potentiometer) position [1/min] (LL, TL, VL, SA, BA) [%] [%] Idle air control Systems without separation for rear window defroster /A/C readiness RPM Idle air control Current learning value Operating conditions for idle air control [1/min]7[1] [8[2]] [9[3]] x0xxx 10[4]
A/C compressor ON Driving range selected A/C readiness, rear window defroster ON always0 Steering to stop
055
Systems with separation for rear window defroster /A/C readiness Learning value for idle Operating conditions
[1/min]
[11[5]]
xxxxx 10
A/C compressor ON Driving range selected A/C readiness ON rear window defroster ON Steering to stop
056
Systems with separation for rear window defroster /A/C readiness RPM (specified value) Idle air control valve Operating conditions [1/min] [13[7]] x0xxx 10
A/C compressor ON Driving range selected A/C readiness, rear window defroster ON always 0 Steering to stop
056
Systems without separation for rear window defroster /A/C readiness RPM (specified value) Idle air control valve Operating conditions [1/min] [14[8]] xxxxx 15[9]
A/C compressor ON Driving range selected A/C readiness, rear window defroster ON Steering to stop
057
Idle air control, pressure signal A/C compressor RPM (actual value) RPM (specified value) A/C compressor
[1/min]
[1/min]
Text: ON/OFF/decreasing
receiver [%]
058 RPM [1/min] 059 Load [%] Engine bearing 1 right Engine bearing 2 left ON/OFF ON/OFF
060
E-Gas adaption Throttle valve angle (potentiometer 1) [%] ESB/E-Gas RPM [1/min]
061
Vehicles with E-Gas Electrically controlled Operating condition throttle valve adaption status [n] Text: ADP runs/ADP OK/ ERROR Systems without separation for rear window defroster /A/C readiness Triggering throttle Operating condition valve control [%] 0xxx 17[2] if possible
A/C compressor ON driving range selected A/C readiness/ r rear window defroster ON
always 0
061
Systems with separation for rear window defroster /A/C readiness Actuating throttle Operating condition valve control [%] xxxx 17
A/C compressor ON driving range selected A/C readiness
062
E-Gas, potentiometer voltage relationship U/Uref Angle sensor 1 for Angle sensor 2 for Sensor 1 accelerator throttle valve drive throttle valve drive pedal position (0->100%) [%] Kick-down adaption Sensor 1 accelerator pedal position (0->100%) [%] (0->100%) [%] Sensor 1 learned Kick-down point (0>100%) [%] (0->100%) [%] Switch
063
Kick-down
Actuated; ADP runs; ADP OK; ERROR Emergency air gap potentiometer 2 [V]
064
Throttle valve potentiometer adaption values Potentiometer 1 lower Potentiometer 2 1 adaption lower adaption [V] [V]
065 066
Cruise control switched free for 4 position operating lever Vehicle speed actual Switch positions Vehicle speed specified [km/h] xxxxxxxx [km/h]
brake light switch Pedal pressed brake pedal switch Pedal pressed clutch switch
Pedal pressed decelerate CC function switched free ADR-Function switched free Resume / Tip up/ acceleration ----0000 CC engaged OFF ----0001 CC tipped OFF ----0011 CC engaged ON (stand by) ----01x1 Set/Tip down/ decelerate ----1011 Resume/Tip up/ accelerate
not used
00 ADR/CC not active (also used for not installed) 01 ADR/CC in control mode 10 Condition over controlled, driver accelerates more than cruise control regulator 11 ADR not released 1: Condition fulfilled 0: Condition not fulfilled
066
Cruise control switched free for 6 position operating lever Vehicle speed actual Switch positions Vehicle speed specified
Switch positions
[km/h]
xxxxxxxx
brake light switch Pedal pressed brake pedal switch Pedal pressed clutch switch Pedal pressed CC function switched free ADR function switched free not used
[km/h] in 1 km/h-steps (is only issued with freely switched cruise control function)
00 ADR/ CC not active (also used for not installed) 01 ADR/ CC in control mode 10 Condition over-controlled, driver accelerates more than cruise control regulator 11 ADR not released 1: Condition fulfilled 0: Condition not fulfilled
Groups 070 - 079: Emission Control Systems (EVAP, Sec. AIR, EGR)
070 Fuel tank venting and valve testing, short trip Opening degree fuel Lambda regular/ tank ventilation18[1] diagnostic value with active diagnose [%] [%] Idle air control valve / diagnostic value with active diagnose [19[2]] / [%] / [g/sec] Result
Test ON/ Test OFF/ Fuel tank ventilation OK/ Fuel tank ventilation not OK. Result
071
Test status
contact Text Reed Open / Reed Closed 072 073 074 Tank leak test
EGR regulator solenoid adaption Null-Position Max. stop [V] EGR, short trip Engine RPM [1/min] [V]
075
Current potentiometer Text value [V] Leak detection pump runs/ LDP OK/ ERROR Systems with Temp.-sensor EGR temperature Result difference [C] Test ON/ Test OFF/ Syst. OK/ Syst. Not OK Systems with intake manifold pressure sensor Intake manifold Result pressure difference [mbar] Test ON/ Test OFF/ Syst. OK/ Syst. Not OK Systems with intake manifold pressure sensor Pressure difference Result diagnostics EGR phase 1 and 3 [hPa] Test ON/ Test OFF/ Syst. OK/ Syst. Not OK Opening degree (U/Uref) EGR potentiometer [%] Opening degree (U/Uref) EGR potentiometer [%] Correction factor in the lower opening range [%] Duty cycle EGR valve
075
EGR, short trip Engine RPM [1/min] Intake manifold pressure [mbar]
075
EGR, for map adaption short trip Pressure difference diagnostics EGR phase 1 and 2 [hPa] Pressure difference diagnostics EGR phase 2 and 3 [hPa]
076
076
[1/min] [mbar] EGR for air mass system Engine RPM Last
076
[1/min] EGR map adaption Actual EGR value potentiometer without offset [V]
[%] Status
077
Test secondary air injection system, short trip, Bank 1 RPM Engine air mass Air mass secondary air injection system [1/min] [g/sec] [g/sec]
Test OFF / Leak detection pump runs/ LDP OK/ ERROR Systems with conventional oxygen sensor Result Test ON/ Test OFF/ Abort Syst. OK/ Syst. Not OK
077
078
078
Test secondary air injection system, short trip, Systems with linear oxygen sensor Bank 1 RPM Engine air mass relative Air mass Result [1/min] [g/sec] [] Test ON/ Test OFF/ Abort Syst. OK/ Syst. Not OK Test secondary air injection system, short trip Systems with conventional oxygen sensor Bank 2 RPM Engine air mass Air mass secondary Result air injection system [1/min] [g/sec] [g/sec] Test ON/ Test OFF/ Abort Syst. OK/ Syst. Not OK Test secondary air injection system, short trip, Systems with linear oxygen sensor Bank 2 RPM Engine air mass Relative air mass Result [1/min] [g/sec] [] Test ON/ Test OFF/ Abort Syst. OK/ Syst. Not OK
079
08 1
dd.mm.yy Error! 12345678 Error! Bookmark not Bookmark not defined. defined. Control module identification (display shown at NA-No. 63) Vehicle identification number Limit No or serial number WVWZZZ1JZWW12345 12345678901234 Control module identification (display shown at NA-No. 63) Flash tool code Flash date Hardware Comp. group type 123
08 2
08 3 08 4 08 5
(FTC) 1234567890123 dd.mm.yy Control module identification Control module identification Control module identification
12
090
090
091
ON/OFF Continuous camshaft adjustment Exhaust Bank 1 RPM Duty cycle Adjustment specified [1/min] [%] [KW] Camshaft adjustment Intake Bank 1 RPM Last Adjustment [1/min] [%] Text ON/OFF Continuous camshaft adjustment, Intake Bank 1 RPM Duty cycle Adjustment specified [1/min] [%] [KW] Camshaft adjustment Intake Bank 2 RPM Last Adjustment [1/min] [%] Text
091
092
092
093
093
094
094
095
095
096
ON/OFF Continuous camshaft adjustment, Intake Bank 2 RPM Duty cycle Adjustment specified Adjustment actual [1/min] [%] [KW] [KW] Camshaft adaption values Intake 2-Bank Systems RPM Last Phase position 20[1] Phase position Bank Bank 121[2] 2 [1/min] [%] [KW] [KW] Continuous camshaft adaption values Phase position Phase position intake Phase position intake Phase position exhaust Bank 1 exhaust Bank 2 Bank 1 Bank 2 [KW] 22[3] [KW] [KW] [KW] Camshaft adjustment Banks 1 and 2 Intake, short trip RPM Camshaft adjustment Test result Bank 1 Test result Bank 2 [1/min] Text: Camshaft Test ON/ Test OFF/ Test ON/ Test OFF/ position ON / Syst. OK/ Syst. Not Syst. OK/ Syst. Not Camshaft position OK OK OFF Continuous camshaft adjustment Banks 1 and 2 intake, short trip RPM Phase position intake Test result Bank 1 Test result Bank 2 [1/min] [KW] Test ON/ Test OFF/ Test ON/ Test OFF/ Syst. OK/ Syst. Not Syst. OK/ Syst. Not OK OK Intake manifold change-over Single step change-over Engine RPM Last Coolant temperature Status [1/min] [%] [C] Text: ein/aus Intake manifold change-over Multi-step change-over Engine RPM Last Coolant temperature Status [1/min] [%] [C] Text: Off /step 1/step 2 Camshaft adjustment Banks 1 and 2 Exhaust, short trip RPM Camshaft adjustment Test result Bank 1 Test result Bank 2
[1/min]
096
097
098
Text: Camshaft Test ON/ Test OFF/ position ON / Syst. OK/ Syst. Not Camshaft position OK OFF Continuous camshaft adjustment Banks 1 and 2 Exhaust, short trip RPM Phase position Test result Bank 1 exhaust [1/min] [KW] Test ON/ Test OFF/ Syst. OK/ Syst. Not OK Intake air change-over / Snow flap RPM Last Temperature / Pressure [1/min] [%] [C]/[mbar] Continuous camshaft adjustment Exhaust Bank 2 RPM Duty cycle Adjustment specified [1/min] [%] [KW]
Test ON/ Test OFF/ Syst. OK/ Syst. Not OK Test result Bank 2 Test ON/ Test OFF/ Syst. OK/ Syst. Not OK Intake air changeover ON/ OFF Adjustment actual [KW]
100
[C]
xxxxxxxx
no warmup cycle
101
[%]
Last
102
103
[1/min] [%] Fuel injection RPM Coolant temperature [1/min] [C] Air-shrouded fuel injectors, short trip RPM Air mass idle air control [1/min] [g/s]
104
Start adaptation values Start engine Temperature temperature adaptation factor 1 [C] [%] RPM (actual) [U/min] Last [%]
105
[1/min]
108 109
111
112
113
[1/min] [C] Boost pressure control Adaption value boost Adaption value boost pressure control RPM pressure control RPM range 1 range 2 [%] [%] Exhaust gas temperature Exhaust gas Enrichment factor temperature Bank 1 sensor Bank 1 [C] [%] Last RPM Last [1/min] [%] Boost pressure control Specified load without Specified load after correction correction [%] [%] Boost pressure control RPM Last [1/min] [%] Boost pressure control RPM Correction factor fuel [1/min] [%] Boost pressure control RPM Gas pedal position
[ms] Adaption value boost pressure control RPM range 3 [%] Exhaust gas temperature Bank 2 [C] Throttle valve angle (potentiometer) [%] Actual load
[%] Adaption value boost pressure control RPM range 4 [%] Enrichment factor sensor Bank 2 [%] Air pressure [mbar] Duty cycle Boost pressure valve [%] Boost pressure actual value [mbar] Correction factor intake air temperature [%] Boost pressure specified [mbar] Boost pressure before throttle valve [mbar] Boost pressure before throttle valve [mbar]
114
[%] Boost pressure specified value [mbar] Correction factor coolant temperature [%] Throttle valve angle
115
116
117
118
119
[1/min] [%] [%] Boost pressure control RPM Intake air temperature Duty cycle boost pressure control valve [1/min] [C] [%] Boost pressure control RPM Actual adaption value Duty cycle boost boost pressure control pressure control valve valve [1/min] [%] [%]
123 124
Reserved for CAN Bus signals Reserved for CAN Bus signals
125
CAN Bus signals Transmission24[1] CAN Bus signals ADR 32 CAN Bus signals All wheel24 CAN Bus signals CAN Bus signals see CAN-Product Description Manual ABS24 Instrument cluster24 LWS 24 Level Airbag24 Steering wheel A/C24 Electrical wiring24
Groups 130-137:
130
Engine cooling
Duty cycle Thermostat [%] Result
Map cooling (coolant filling), Short trip Temperature Temperature Engine outlet [C] Radiator outlet [C]
131
Map cooling Temperature Engine outlet [C] Map cooling Temperature Radiator outlet (specified) [C]
Temperature Engine outlet (specified) [C] Temperature difference Engine and radiator outlet [C]
132
[%]
xxxxxxxx
Error in system Thermostatactuation active Cooling van triggering active Control deviation 0 > specified temp. 1 < specified temp Fan stage 2 active Fan stage 1 active not used not used 1: Description fulfilled 0: Description not fulfilled
133 134 Temperature Oil temperature Ambient temperature Intake air temperature Engine outlet temperature
135
[C] [C] Coolant fan control, short trip Temperature Duty cycle Radiator outlet (specified) [C] Coolant fan actuation 1 [%]
[C] Result
136
137
Relay for coolant fan actuation Relay 1 Relay 2 ON / OFF ON / OFF A/C requirements AC-inlet Compressor
Relay 3 ON / OFF High pressure switch or Pressure of A/C system ON / OFF or [bar]
ON / OFF
ON / OFF
[%]
Groups 140-147:BDE
140 Pressure control valve, short trip Duty cycle DSV Rail pressure specified [bar] [ ] Rail pressure actual [bar] Result Text: Test ON/ Test OFF/ Syst. OK/ Syst. Not OK 141 Fuel supply system Rail pressure regulator Regulator rail pressure system Regulator rail pressure system residual portion [-] Status rail pressure system
[-]
[-]
Exhaust gas temperature sensor, short trip Exhaust gas Exhaust gas temperature from temperature sensor model Bank 1 measured Bank 1 [C] [C]
Result
146 147 Charge movement flap for BDE Charge movement flap Actual position [%]
Adaptation condition
Text ADP runs/ ADP OK/ Error (in emergency running mode)
161