Professional Documents
Culture Documents
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
1)Press *#3685247#* 2)Select ''Network & call settings'' 3) Select "Service Domain" 4) Select "CS" 5) Press ''Save``
This way you can verify Central frequency from the phone pad, by locking the phone to UMTS850 or UMTS1900 (In Chicago for UMTS850 it is 4384 and UMTS1900 is 612) (In Montreal, Canada for UMTS850 it is 1087(UMTS V(850 Mhz) and UMTS1900 is 587(UMTS II 1.9Ghz)) AT Command Air CARD Lock up Connect to AIR CARD AT!ENTERCND=A710 (TO CONNECT TO AIR CARD) To Lock the Air card to UMTS UMTS AUTO 850/1900 AT!GBAND=03FFFFFFF( or Also in 3G Watcher you can check 3G only) UMTS 850 AT!GBAND=04000000 UMTS 1900 AT!GBAND=0800000 To Lock the Air card to GSM GSM AUTO 850/1900 AT!GBAND=03FFFFFFF( or Also in 3G Watcher you can check 2G only) GSM 850 AT!GBAND=0280000 GSM 1900 AT!GBAND=0200000 To verify the Air card locked Mode for GSM/UMTS AT!GBAND? 3 Pervez Durrani RF Engineer GTLAmericas 910-5391026
Winsock Error:
TCP/IP is a set of communications protocol used for the internet and other similar networks. TCP/IP can sometimes get damaged or corrupted, in case you can't connect to the internet and have tried various other methods with no success, most probably corrupted TCP/IP is the reason behind it. As TCP/IP is a core windows component it can't be removed , however , it can be reset/repair to its original state by couple of methods mentioned below. Method 1: 1) Go to Start menu and open command prompt. 2) At the command prompt , copy and paste(or type) the following command and then press ENTER:
netsh int ip reset c:\resetlog.txt
When we run the reset command, it rewrites two registry keys that are used by TCP/IP. This has the same result as removing and reinstalling the protocol. 3) Reboot the computer and you should be all set. Method 2: An easier way is to just click either of these links, start winsock.dll download and then reboot your computer : http://www.online-tech-tips.com/computer-tips/winsock-fix/
OR
http://support.microsoft.com/?kbid=299357
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
General Precautions:
5 Pervez Durrani RF Engineer GTLAmericas 910-5391026
Make sure all the hardware is getting enough power from the car battery through inverter. Make sure to tape the connected power cables to reduce short circuit risks. Make sure to carry extra cables. Make sure to save Scanner\Phone drivers on the laptops.
HOW TO FORCE COMPASS 888 TO SPECIFIC CHANNEL (Montreal Canada TELUS IN THIS CASE)
1)WITH THE HELP OF HYPERTERMINAL SELECT AUTO BAND SELECTION USING AT!ENTERCND=A710 AT!GBAND=3FFFFFFF 2)OPEN SIERRA WIRELESS WATCHER SET NETWORK SELECTION IN AUTOMATIC MODE
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
3)AGAIN OPEN HYPERTERMINAL USE THESE COMMANDS AT!ENTERCND=A710 AT!CUSTOM=HSDPATEST,1 AT!RESET PLEASE GIVE SUFFICIENT TIME FOR COMPASS TO RESET COUPLE OF MINS IS OK. 4) OPEN SIERRA WIRELESS WATCHER AND GOTO NETWORK NOW YOU CAN FIND NEW HSDPATEST SETUP SETTING ADDED IN NETWORK TAB
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
5) In HSDPA Test Setup . We need to do this in proper sequence a) Enabled Yes PLEASE DO NOT RESCAN BEFORE PUTTING RIGHT CHANNEL AS IF NOW b) Channel Number is Centre frequency of 850 Band. As 850 Band usually camps on Rogers and we need to force Telus channel number in this case. USE YOUR 850 BAND CENTRE FREQUENCY IN CHANNEL NUMBER. c) Apply d) Rescan Now Yes Please give sufficient time for Compass to catch the right channel. e) Press OK Cross your fingers for Blue light on compass Please check that following criterias are met when you do a Scope 2 stationary test.
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
Stationary TEST: For stationary test keep the following points in mind
1) Right scrambling code is isolated ( single SC serving) 2) Rx Power below -75 3) Download throughput more than 5500 kbps 4) Upload throughput more than 1200 kbps (to check upload throughput open device views - 0850PSHSUPA throughput chart. 5) Ping - Time less than 70ms (milliseconds) This is most important. Unfortunately you can not see ping time in Agilent for that you need to do this a) connect to internet through dialup modem (HSPA_PS or any other you created) b) open Start ------ Run-------- cmd------- this will open command/Dos prompt c) type this to check ping time ping -t 10.179.253.14 if ping is less than 70ms constantly then you can start test otherwise..... d) open website www.google.com and check whether ping time become ok if yes then you should keep that Google website open and when Agilent start connecting for ping just refresh the Google page. make sure you dont pass 3/4 pings before you refresh. 6) Attach / Detach test are with 15 sec wait time between each other so in both test put wait time 15 seconds. 7) Dont forget to do manual video calls.
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
C888 Firmware upgrade and toolsV2.doc: 1) Download FW upgrade (a) and Watcher upgrade (b) as follow: a) https://extranet.sierrawireless.com/engineering/approva ls/filedrop b) user: password: swirguest filedrop
File: BZ16435_K2_0_6_5BT_K2_0_6_7AP_EnableDirectIp.zip b) Watcher_Generic_2062.msi which is available on Sierra web site as follow: http://www.sierrawireless.com/resources/software/watche r/Build2062/Watcher_Generic_2062.msi 2) Disconnect physically all external modems and C888 from the PC 3) Remove previous modem created with C888 on PC (control panel -> phone and modems options):
10
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
4) Uninstall all COM ports created for the Sierra C888 on PC called Sierra Wireless Application Interface and Sierra Wireless Diagnostic Interface (control panel -> System -> Hardware TAB -> Device Manager -> Ports (COM&LPT)):
5) Remove previous watcher installed on PC (control panel -> add or remove programs):
11
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
12
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
6) Delete in program files the directory of the 3G watcher and the True Install
7) Install new Watcher with following file downloaded previously (C888 should be physically disconnected from PC): Watcher_Generic_2062.msi 8) Disconnect all modems from PC and have C888 physically connected alone with Watcher OFF (Watcher will start automatically during FW upgrade). Double click FW upgrade file and C888 will be detected and FW download and upgrade will start (upgrade file: BZ16435_K2_0_6_5BT_K2_0_6_7AP_EnableDirectIp.exe). This will take 10 to 20 minutes, PC activity should be minimized and C888 should not be ejected during the upgrade. a) Download phase 1 (automatic):
13
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
9) With C888 still physically connected on PC, run the following exe file to enable DM port and dialup modem. Those ports are mandatory for drive test data collection with Agilent:
14 Pervez Durrani RF Engineer GTLAmericas 910-5391026
10) The above FW allows HSDPA cat8 (7.2Mbps max) with no further action 11) The above FW allows HSUPA cat5 (2.1Mbps max) with no further action 12) Upgrade to HSUPA cat6 (5.76Mbps) is possible with following AT command (using AT com port of the device) but this FW is running on a Beta release for HSUPA cat6: AT!HSUCAT=6 AT!HSUCAT=5 (limit capability back to HSUPA cat5) 13) Monitoring tool is available to force bands and verify key indicators from the C888 (exe file below).
15
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
16
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
Hyper Terminal:
To access Hyper Terminal: Click on the Hyper Terminal Icon:
17
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
After this you can access the Hyper Terminal window to write in
18
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
Connection
It will bring you new window: New Connection Wizard click next
19
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
Important: Conform the port from Device Manager under Modem drop down
20
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
You can Name whatever you want it: Here we named it as HSDPA
In this case phone number is *99#(however in each market you get this number)
21
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
Put AT command in device manager under USB Modem, find the port and then go to advance and add the AT command there(Very Important)
22
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
23
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
RSCP = Received Signal Code Power = UE Aggregate Ec (dbm) and this roughly correlates to SC Analyzer Aggregate Ec (dbm).
Step 1: For UE
RSCP by opening a data items panel for the UE, expanding the data items, expanding the data item called UMTS Pilot Channel and selecting Active RSCP (dbm). Open a common view, a bar chart, and then drag and drop the Active RSCP data item into the bar chart. This will look just like the Top N SC Ec/Io view, except that you will see RSCP (dbm) versus common pilot channel CPICH (Ec/Io) which is shown in the Top N Sc Ec/Io view.
Step 2 : Scanner
Aggregate Ec (dbm) in the Scrambling Code Analyzer, open a common receiver bar chart view. Expand the data items under the W-CDMA Scrambling Code Analyzer, expand W-CDMA Top N Scrambling Codes, select SC Agg Ec and drag and drop it into your receiver bar chart view.
Agilent help
Refer to Help in the software if you need assistance configuring the views. Or call 1-800-829-4444 for assistance.
24
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
Workspace examples for different set up: First unzip this and then open the project as a file in Agilent
Workspace_1.zip
25
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
26
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
W-CDMAUMTS Scrambling Code Analyzer 850: Important: Downlink. Every market has different center frequency Please ask for it? IN CHICAGO: For UMTS 850 Channelization: UMTS V (850MHz general) Center Frequency(Downlink)=4384 Preselect or : 864.00MHz-899.00Mhz
IN CHICAGO: For UMTS 1900 Channelization: UMTS II(1.9GHz) Center Frequency(Downlink)=612 Preselect or : 1.925GHz-1.995GHz
27
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
Sequence: Root:
SERVICE_MODEL:
PARALLEL_SEQUENCE:
28
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
GNG1-CSShortMO: Properties
29
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
30
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
GNG1-UMHSPLong: Properties
31
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
32
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
GNG1-UMHSPLong:
DISCONNECT_TEST: Properties
Check Errors? Network error: At IP address here in Chicago for Download and upload is 209.183.33.5 Use PING command for verification of the server OR on the down load and up load laptops only check FTP and run the sequence. Ping 209.183.33.5 User Name: ericsson Password: ericsson3g Windsock error 100609 is network error, ip address is not reach able
New IP Address:
IP address: 64.124.55.102 User Name: chicago Password: chicago2009 For Down load you have to create 5000k Band width folder at the above location, so that you can download the data. For Upload you have to create 3000k Band width folder at the above location, so that you can upload the data.
33
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
Sequencer: Properties
34
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
Sequencer: Properties:GNG1-CSLongMO
35
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
36
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
37
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
Agilent Software
Scope two Stationary Test
Important steps
1. 2. 3. 4. 5. 6. 7. 8.
SC should be isolated CS 1 and CS 2 Rx should be less than -70 PS or Air card Rx power should also be less than -70 PS ( download ) throughput should be more be 5500 PS ( upload ) should be more 1500 Entire test perform only on laptop B except 1900 video calls has to be done on laptop A Video calls should be done manually on both the laptops More importantly each test should pass and if for some reason any one of test fails, we have to re do the entire test again.
38
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
Required Hardware's
Two cell phones locked under the band of UMTS 850 CS connected to laptop B GPS connected to laptop B Air card or PS1 connected to laptop B Two cell phones locked under the band of UMTS 1900 CS connected to laptop A
SC
39
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
Upload chart
Upload > 1500
Ping test
40
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
Properties of 850PS1
41
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
42
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
43
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026
Video calls
30 video missed calls from CS1 to CS2 and duration of each missed calls should not be more 10 seconds. 30 video missed calls should be perform on both the laptops A & B (1900 and 850 )
44
Pervez Durrani
RF Engineer
GTLAmericas
910-5391026