Professional Documents
Culture Documents
INSTALLATION INSTRUCTIONS
Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the contents of this booklet in order to properly install and use the satellite radio kit. Your safety depends on it. Keep these instructions with your vehicle records for future reference.
WARNING
x There are several WARNING and CAUTION sections in this booklet concerning safety when installing. Always read and follow them in order to prevent injuries, accidents, and possible damage to the vehicle. WARNING: Indicates a situation in which serious injury or death could result if the warning is ignored. CAUTION: Indicates a situation in which bodily injury or damage to the vehicle could result if the caution is ignored. x If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent errors in installation. x If you have any questions about the use of the accessory, ask your Mazda dealer for proper advice before using it. x Mazda and its suppliers are not responsible for injuries, accidents, and damage to persons and property that arise from the failure of the dealer or installer to follow these instructions. x To ensure safety and reliability of the work, installation, removal and disposal work done by an Authorized Mazda Dealership is recommended. x Be careful not to lose removed parts, and be sure that they are kept free from scratches, grease or other dirt.
NOTE To the dealer x Please turn over these instructions to the customer after installation. To the customer x Keep these instructions after installation. The instructions may be necessary for installing other optional parts or removal of this accessory. x Should the vehicle or this accessory be resold, always leave these instructions with it for the next owner.
1ED6P11A22000 1
INSTALLATION VIEW
ANTENNA CABLE
4-Door
5-Door
Antenna
Antenna
Antenna cable
Antenna cable
GND
To Audio unit
SIRIUS only
To Vehicle wiring harness 4 pin connector To AUX or Bluetooth H/F Not used Tie redundant part DLP unit Antenna cable
GND
To Audio unit Tie redundant part To Vehicle wiring harness 4 pin connector
CONNECTION DIAGRAM
iPod (On market product)
Audio unit
CAN (+) CAN (-) CAN (-) 16 pin connector CAN (+) Harness (H3) iPod integration module NO CONNECT iPod connection cable
4 pin connector
Antenna cable
CAUTION
z When connecting a connector, be sure to insert it straight along the guide. The connector terminal may be bent if inserted at an angle.
Not used (Wrap with sponge and vinyl tape) CAN (+) 16 pin connector Harness (H3) CAN (-)
4 pin connector
Antenna cable
CAUTION
z When connecting a connector, be sure to insert it straight along the guide. The connector terminal may be bent if inserted at an angle.
PARTS
Note x Verify that the kit includes all the following parts and that they are free of dirt, scratches or damage. x All hardware required to install is contained in the two Satellite Radio Kits below.
Qty. 1
Part
Qty. 1
0000-81-L17
Nut 2
Urethane
Sponge
28
Clip
Butyl tape
Installation instructions
BEFORE INSTALLATION
Rating label
1. Tear off lower part of the rating label on the bottom of DLP unit. 2. If there is nothing written in the Sirius ID (ESN) space of the rating label, write down the 12-digit number printed in the location shown in the figure. 3. Affix one rating label in the last page of the Owners Manual.
DLP unit
Note x The other rating label is for the dealer (port) records. x Do not fail to submit the record.
Tear off Affix to the back of the Owners Manual. Submit to the manager of installation department.
Rating label
REQUIRED TOOLS
Prepare the following tools or items before installation. Phillips screwdriver Socket driver (8 mm, 10 mm) Socket wrench Torx wrench Scissors Fastener remover Drill ( 4mm, 10mm drill bits) Cutter knife Scale Pen marker Vinyl tape Soft cloth Mat ISP alcohol
WARNING
When the negative battery cable is connected during operation, it may cause electric shock or other personal injuries. Disconnect the negative battery cable before removal/installation. When connecting/disconnecting connectors, grasp the connectors, not the wires. Otherwise a short, an accident from poor contact or fire may occur. Do not pull the harness with excessive force. Doing so can cause a breakage or a short-related accident, as well as an electrical short or fire. Secure the harness with the band (part included) so it doesnt dangle. If not, it may cause a short, accident, or fire.
CAUTION
Put the removed parts and the parts in the kit on the protective sheet to prevent scratches. Using improper tools may cause damage and or broken parts. Use the correct tool for the job. Be sure to cover the vehicle body with protectors or mats to prevent stains, scratches and damage when removing/installing the vehicle parts. Excessive length of tie wrap may interfere with other parts and cause damage. Cut unnecessary part up to about 5 mm {0.19 in} from the fixed point.
20 {0.78} mm {in}
sure the cable is not pinched, knotted kinked or coiled too tightly. It is recommended that a coil of less than 20 mm {0.78 in} be avoided if possible. x If this wiring procedure is not followed, the performance of the antenna will be affected and could result in increased audio muting.
Note
x When the negative battery cable is removed, the clock, radio, trip meters and other memories will be erased. Before performing work, record the content of the memory.
PART REMOVAL
WARNING
x When the negative battery cable is connected during operation, it may cause electric shock or other personal injuries. Disconnect the negative battery cable before removal/installation.
NOTE
x The procedure described here is for a left-hand drive vehicle, however, perform work in the same manner for a right-hand drive vehicle as well.
Vehicle front
WARNING
x When removing/installing the parts, park the vehicle on level ground and apply the side brake securely. Be sure to turn the ignition switch off, otherwise the vehicle can move, causing personal injury or vehicle damage. 2. Disconnect the negative battery cable and wrap tape around it to insulate.
WARNING
x When the negative battery cable is connected during operation, it may cause electric shock or other personal injuries. Disconnect the negative battery cable before removal/installation.
Vehicle front
A B
Clip C
Vehicle front
Clip A
2. Pull the front side trim in the direction shown by the arrow, then detach clip A.
Fastener
Hook A
Hook B B
A B Upper panel
Hook C
Hook D
2. Pull the upper panel in the direction of the arrow shown in the figure, then remove it while detaching the hook C (1 location) and hooks D (2 locations). 3. Remove the upper panel.
D C D Upper panel
1. Remove the shift knob (MTX) or selector lever knob (ATX). 2. Pull the shift panel in the direction of the arrow shown in the figure and remove it while detaching the clips A (3 locations), hook B (1 location) and guide C (2 locations). 3. Disconnect the sear warmer switch connector. (For vehicles with seat warmer) 4. Disconnect the accessory socket connector. 5. Remove the illumination bulb.
A Shift panel
1. Pull out the side wall in the direction of the arrow (1) shown in the figure, then remove the clips A (2 locations). 2. Remove the side wall in the direction of the arrow (2) shown in the figure.
Console removal
Vehicle front
1. Remove the bolts (2) and the screws (2). 2. Disconnect the accessory socket connector.
Bolt
Console
Screw
Vehicle front
A A A
A B A Clip A Guide B
(1) (3)
A A A B A A
3. Pull the console in the direction of the arrow (1) shown in the figure, then detaching clips A (10 locations) and guides B (2 locations). 4. Pull up the console in the direction of the arrow (2) shown in the figure, move the rear console in the direction of the arrow (3), and remove it avoiding the parking brake lever.
(2)
Hook
(1)
Hooks
Vehicle front
(2)
(1)
10
Connectors
1. Remove the screws (3). 2. Disconnect the connectors (2 locations). 3. Detach the clips (3 locations), and then remove the instrument cluster.
with the display side up to prevent grease from leaking from the meters. NO GOOD Display facing downward Display facing upward
GOOD
Clips
Vehicle front
Hook A A B
Pin B A B
1. Detach the hooks A (2 locations) in the direction of arrow (1) shown in the figure. 2. Pull the dashboard under cover in the direction of arrow (2) while remove the pins B (2 locations).
(2)
Vehicle front
3. Remove the dashboard under cover in the direction of arrow (3) shown in the figure, then remove the guide.
Guide
Guide
11
Screw Tab
1. Pull the lever. 2. While pushing the tab in the direction of the arrow using a tape-wrapped, small flathead screwdriver, detach it from the lower panel.
(2)
: Clip : Pin : Guide : Hook
2. Remove the screws. 3. Pull the lower panel in the direction of the arrow in the order of (1) (2), (3) and remove the lower panel while detaching the hook, clips, guide and pins.
12
Tab A Pin D (2) (1) Tab E (3) Hook B Clip C (4) Hook F Vehicle front
1. Detach tab A while pulling the rear scuff plate in the direction of the arrow (1) shown in the figure, then detach hook B, clips C, pins D while pulling in the direction of the arrow (2). 2. Detach tab E while pulling the rear scuff plate in the direction of the arrow (3) shown in the figure, pull the rear scuff plate in the direction of the arrow (4) shown in figure.
Pin B Clip D
1. Partially peel back the seaming welt. 2. Pull the B-pillar lower trim in the direction of the arrow (1), (2) shown in the figure, detach pin A, tab B, pin C, clip D. 3. Remove the B-pillar lower trim in the direction of the arrow (3) showm in the figure.
Vehicle front
1. Detach the hooks from the grommets by pulling the rear seat cushion in the order of (1), (2) in the direction of the arrow shown in the figure.
(2)
NOTE x The procedure for the 4-door model begins from x The procedure for the 5-door model begins from
page 16. page 14.
(1)
Hook
Grommet
13
4-Door
Fastener Tire house trim Vehicle front Vehicle front
Clip A Pin B
Clip A
Pin C
Pin B
Pin C
1. Remove the fasteners. 2. Pull the trunk end trim indicated in the arrow shown in the figure, then detach clips A, pins B, pin C, D and tabs E. 3. Remove the trunk end trim.
Clip A
Fastener
Pin D
Pin B
Clip A Pin C
Pin D
Tab E
Fastener
Fastener
Vehicle front
14
Nut
3. Pull the rear combination light in the direction of the arrow shown in the figure and disengage the hook from the clip and remove the rear combination light.
Vehicle front
Clip
Hook
15
5-Door
Tire house trim (passengers side) removal
Hook A Tire house trim Hook B Vehicle front
1. Remove the fasteners. 2. Pull the tire house trim in the direction of arrow (1), while remove the hook A and B. 3. Pull the tire house trim in the direction of arrow (2), while remove the clip C, pin D and E. 3. Remove the tire house trim.
(2)
Clip C
Hook A
Hook B
Pin D
Pin E
Guide D
Guide D
Pin E
Fastener
Hooks
Screw
Fastener
Clips
Hook
Clip
Hook
Vehicle front
16
Screws
Nut Connectors
17
1. Install the DLP unit to the dashboard member. 2. Install the nuts (2 locations). x Nut tightening torque: 7.8 11.0 N m {80.0 112.0 kgf cm 70.0 97.0 in lbf }
Vehicle front
Nut
18
Trunk lid
Center
Trunk lid
Trunk lid
3. Clean the adhesion area on the trunk lid with isopropyl alcohol (IPA). 4. Attach the clips to the trunk lid. 5. Install the antenna cable to the clips of the trunk lid. 6. Secure the antenna cable to the vehicle wiring harness with tie wraps (large). 7. Pull the seaming welt and route the antenna cable inside the seaming welt.
CAUTION
Antenna cable Tie wraps (large) Seaming welt mm {in}
19
8. Pull the seaming welt up slightly on the flange and route the antenna cable under the outside lip.
Butyl tape
Antenna cable
Seaming welt
35 {1.37} 20 {0.78}
20 {0.78}
30 {1.18}
CAUTION x To ensure proper affixing, be sure to degrease the x Do not wrap butyl tape around flange. x Do not double-layer tape.
area where the pad protector is affixed.
Butyl tape should hold the antenna cable to the sheet metal as shown. x Take care not to trap antenna cable under attachment nuts.
10. Secure the antenna cable to the vehicle wiring harness with tie wraps (small).
Vehicle front
Antenna cable
11. Secure the antenna cable to the vehicle wiring harness with tie wraps (small). Go to Step 12 on page 23.
Vehicle front
20
5-Door
Roof Adhesion area 170 {6.69}
1. Clean the adhesion area on the roof with isopropyl alcohol (IPA).
Vehicle front
mm {in}
Vehicle front
mm {in}
3. Clean the adhesion area on the body shell with isopropyl alcohol (IPA). 4. Attach the clips to the body shell. 5. Install the antenna cable to the clips of the body shell. 6. Pull the seaming welt and route the antenna cable inside the seaming welt.
21
7. Pull the seaming welt up slightly on the flange and route the antenna cable under the outside lip.
Antenna cable
mm {in}
Butyl tape should hold the antenna cable to the sheet metal as shown. x Take care not to trap antenna cable under attachment nuts.
Antenna cable
9. Secure the antenna cable to the vehicle wiring harness with tie wraps (small). Go to Step 12 on page 23.
Vehicle front
22
12. Secure the antenna cable to the vehicle wiring harness with tie wraps (small).
Antenna cable
Vehicle front
13. Route the antenna cable through the vehicle wiring harness.
Antenna cable
Vehicle front
Vehicle front
14. Secure the antenna cable to the vehicle wiring harness with tie wraps (large). 15. Bundle the antenna cable into a loop and temporary fix it with vehicle wiring harness using the tie wrap (large). 16. Secure the antenna cable with pad protector.
17. Secure the antenna cable to the vehicle wiring harness with tie wrap (large).
Antenna cable
Vehicle front
23
DLP unit
24
Dashboard
Vehicle front
Pad protector
Pad protector
2. Affix the double-sided adhesive tapes to the iPod integration module as shown in the figure.
25
CAUTION x To ensure proper affixing, be sure to degrease the x Affix the iPod integration module so that it does not
Tie wraps (large)
area where the double-sided adhesive tape is affixed. cover the 10 mm dia. hole which was drilled in the dashboard in the previous step.
Vehicle front
2. Route a tie wrap (large) through the 10 mm dia. hole in the dashboard and secure the iPod integration module using the tie wrap.
650 {25.59}
Glove compartment
26
Vehicle front
Dashboard
2. Connect the harness (H3) and iPod connection cable to the iPod integration module.
Harness (H3)
Vehicle front
Pad protector
Dashboard
3. Secure the harness (H3) to the dashboard with pad protector. 4. Secure the harness (H3) to the vehicle wiring harness with tie wrap (small).
Vehicle front
Harness (H3)
27
Electro-taps Urethane
5. Branch connect the CAN (+) wires to the cluster 1 24-pin connector (terminal C) using taps. 6. Branch connect the CAN (-) wires to the cluster 1 24-pin connector (terminal E) using taps.
Instrument cluster1 24 pin connector (wire color)
Vehicle front
7. Wrap the electro taps and vehicle wiring harness together using urethane. 8. Secure the harness (H3) to the vehicle wiring harness with a tie wrap (small).
9. Secure the GND wire of harness (H3) to the vehicle wiring harness with tie wraps (large). 10. Tighten the GND wire of wiring harness (H3) using the vehicle GND nut. x Nut tightening torque: 7.6 11.0 N m {78.0 112.0 kgf cm 68.0 97.0 in lbf }
Vehicle front
28
11. Secure the harness (H3) and iPod connection cable using tie wraps (large) as shown in the figure.
To audio unit
Vehicle front
12. Affix the pad protector to the dashboard member as shown in the figure.
Harness (H3)
16. Connect the harness (H3) 4 pin connector to the vehicle wiring harness 4 pin connector. 17. Affix the harness (H3) to the rear heat duct using a pad protector and a tie wrap (large).
Vehicle front
29
Harness (H3)
DLP unit
Vehicle front
Antenna cable
Harness (H3) Tie wraps (large) Dashboard member iPod connection cable Vehicle front
19. Secure the excess wiring harness (H3), iPod connection cable, and antenna cable together to the dashboard member using a tie wrap (large). 20. Align a tie wrap (large) with the position marked on the iPod connection cable and secure them together to the vehicle wiring harness.
30
Vehicle front
Dashboard
Pad protector
2. Affix the pad protector to the dashboard member as shown in the figure. 3. Wrap the iPod integration module connector with the sponge and vinyl tape, and affix to the dashboard member using a tie wrap (large).
Sponge
Vinyl tape
Vehicle front
4. Secure the GND wire of harness (H3) to the vehicle wiring harness with tie wraps (large). 5. Tighten the GND wire of wiring harness (H3) using the vehicle GND nut. x Nut tightening torque: 7.6 11.0 N m {78.0 112.0 kgf cm 68.0 97.0 in lbf }
Vehicle front
31
6. Secure the harness (H3) using the tie wraps (large) as shown in the figure.
To audio unit
Vehicle front
7. Affix the pad protector to the dashboard member as shown in the figure.
Harness (H3)
11. Connect the harness (H3) 4 pin connector to the vehicle wiring harness 4 pin connector. 12. Affix the harness (H3) to the rear heat duct using a pad protector and a tie wrap (large).
Vehicle front
32
DLP unit
Vehicle front
Antenna cable
14. Secure the excess wiring harness (H3) and antenna cable together to the dashboard member using a tie wrap (large).
Vehicle front
33
10
CAUTION x After installing the vehicle parts, check for dirt. Clean any dirty parts.
x Perform the Inspection indicated on the last page of these installation instructions.
CAUTION
x When the battery is disconnected, the windows will not fully open and close automatically. Perform the following procedure to resume operation: 1. Turn the ignition switch to the ON position. 2. Press the switch and fully open the window. 3. Pull up the switch and continue holding for about 2 seconds to fully close the window. 4. If the function does not operate even after the ignition switch is turned off, contact an Authorized Mazda Dealer.
34
11
INSPECTION
Inspection Items ( ) Scratches/ Installation/ Dirt/ Tightening/ Harness Engagement interference
x Inspect the installed / reinstalled parts for the following items. x Inspection parts differ depending on the vehicle.
Inspection Parts
Clearance/Fit
Operation check
Rear combination light (passengers side) Trunk side upper trim (passengers side) 5-Door Trunk side trim (passengers side) Trunk end trim Tire house trim (passengers side) Rear seat cushion B-pillar lower trim (passengers side) Rear scuff plate (passengers side) Lower panel (passengers side) Glove compartment Hood release lever Lower panel (drivers side) Dashboard under cover Instrument cluster Upper column cover Center cover Center panel module Center panel upper Console Side wall (drivers side / passengers side) Shift panel lower Upper panel Front side trim (drivers side / passengers side) Front scuff plate (drivers side / passengers side) Battery cable Battery cover *1
: Applicable *1: Refer to the Owners Manual and the SATELLITE RADIO instruction manual, and verify that the system operates correctly. Ex.: Turn the power ON, increase the volume, and press the SAT button. x Direct access channel 184 is a test channel provided by Sirius. Press the SAT button on the radio, and if properly installed you will receive a signal from the Sirius broadcast. Note: Sirius broadcasts can only be received in an open area, enclosed spaces such as garages or work buildings block the satellite reception. Date , , Vehicle. VIN. Approved Checked Person in charge