Professional Documents
Culture Documents
SERVICE MANUAL
S10V313VTN200
MODEL
13VT-N200
In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its original condition and only parts identical to those specified should be used.
CONTENTS
Page IMPORTANT SERVICE SAFETY PRECAUTION .................................................................................... 2 ELECTRICAL SPECIFICATIONS ............................................................................................................. 6 LOCATION OF USERS CONTROL ......................................................................................................... 7 DISASSEMBLY AND REASSEMBLY .......................................................................................................9 INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................. 12 PRECAUTIONS IN REASSEMBLING....................................................................................................17 FUNCTION OF MAJOR MECHANICAL PARTS .................................................................................... 18 ADJUSTMENT, REPLACEMENT AND ASSEMBLY OF MECHANICAL UNITS .................................... 20 ADJUSTMENT OF THE VCR ELECTRICAL CIRCUITRY ..................................................................... 40 TROUBLESHOOTING ............................................................................................................................ 42 CHASSIS LAYOUT ................................................................................................................................. 54 BLOCK DIAGRAM OF TV SECTION .....................................................................................................56 BLOCK DIAGRAM OF VCR SECTION .................................................................................................. 58 OVERALL SCHEMATIC DIAGRAM ....................................................................................................... 68 DESCRIPTION OF SCHEMATIC DIAGRAM ......................................................................................... 70 PRINTED WIRING BOARD ASSEMBLIES ............................................................................................ 82 REPLACEMENT PARTS LIST ............................................................................................................... 86 PACKING OF THE SET ........................................................................................................................103
SHARP CORPORATION
This document has been published to be used for after sales service only. The contents are subject to change without notice.
13VT-N200
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines which follow: X-RADIATION AND HIGH VOLTAGE LIMITS
1. Be sure all service personnel are aware of the procedures and instructions covering X-radiation. The only potential source of X-ray in current solid state TV receivers is the picture tube. However, the picture tube does not emit measurable X-Ray radiation if the high voltage is as specified in the "High Voltage Check" instructions. It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the picture tube including the lead in glass material. The important precaution is to keep the high voltage below the maximum level specified. 2. It is essential that servicepersonel have available at all times an accurate high voltage meter. The calibration of this meter should be checked periodically. 3. High voltage should always be kept at the rated value -no higher. Operation at higher voltages may cause a failure of the picture tube or high voltage circuitry and;also, under certain conditions, may produce radiation that exceeds specifications. 4. When the high voltage regulator is operating properly there is no possibility of an X-radiation problem. Every time a color chassis is serviced, the brightness should be tested while monitoring the high voltage with a meter to be certain that the high voltage does not exceed the specified value and that it is regulating correctly. 5. Do not use a picture tube other than that specified or make unrecommended circuit modifications to the high voltage circuitry. 6. When trouble shooting and taking test measurements on a receiver with excessive high voltage, avoid being unnecessarily close to the receiver. Do not operate the receiver longer than is necessary to locate the cause of excessive voltage.
WARNING
1. For continued safety, no modification of any circuit should be attempted. 2. Disconnect AC power before servicing. 3. Semiconductor heat sinks are potential shock hazards when the chassis is operating. 4. The chassis in this receiver has two ground systems which are separated by insulation material. The nonisolated (hot) ground system is for the B+ voltage regulator circuit and the horizontal output circuit. The isolated ground system is for the low B+ DC voltages and the secondary circuit of the high voltage transformer. To prevent electrical shock use an isolation transformer between the line cord and power receptacle, when servicing this chassis. CAUTION: FOR CONTINUED PROTECTION AGAINST A RISKOF FIRE, REPLACE ONLY WITH SAME TYPE 4A125V FUSE.
4A 125V
SERVICING OF HIGH VOLTAGE SYSTEM AND PICTURE TUBE When servicing the high voltage system, remove the static charge by connecting a 10k ohm resistor in series with an insulated wire (such as a test probe) between the picture tube ground and the anode lead. (AC line cord should be disconnected from AC outlet.)
1. Note that the picture tube in this receiver employs integral implosion protection. 2. Replace with tube of the same type number for continued safety. 3. Do not lift picture tube by the neck. 4. Handle the picture tube only when wearing shatterproof goggles and after discharging the high voltage anode completely.
13VT-N200
AC VOLTMETER
1.5k ohm 10W
SAFETY NOTICE
Many electrical and mechanical parts in television receivers have special safety-related characteristics. These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage and etc. Replacement parts which have special safety characteristics are identified in this manual; electrical components having such features are identified by "" and shaded areas in the Replacement Parts Lists and Schematic Diagrams. For continued protection, replacement parts must be identical to those used in the original circuit. The use of a substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock, fire, X-radiation or other hazards.
13VT-N200
Ne peut effectuer la rparation qu' un technicien spcialis qui s'est parfaitement accoutum toute vrification de scurit et aux conseils suivants. LIMITES DES RADIATIONS X ET DE LA HAUTE TENSION
1. Tout le personnel rparateur doit tre instruit des instructions et procds relatifs aux radiations X. Le tube-image, seule source de rayons X dons les tleviseurs transistoriss, n'met pourtant pas de rayons mesurables si la haute tension est maintenue un niveau prconis dans la section "Vrification de la haute tension". C'est seulement quand la haute tension est excessive que les rayons X peuvent entrer dans l'enveloppe du tube-image y compris le conducteur de verre. Il est important de maintenir la haute tension en-dessous du niveau spcifi. 2. Il est essentiel que le rparateur ait sous la main un voltmtre haute tension qui doit tre priodiquement talonn. 3. La haute tension doit toujours tre maintenue la valeur de rgime-et pas plus haute. L'opration des tensions plus leves peut entraner une panne du tube-image ou du circuit haute tension et, dans certaines conditions, peut entraner une radiation dpassant les niveaux prscrits. 4. Quand le rgulateur haute tension fonctionne correctement, il n'y a aucun problme de radiation X. Chaque fois qu'un chssis couleurs est rpar, la luminosit doit tre examine bout en contrlant la haute tension l'aide d'un voltmtre pour s'assurer que la haute tension ne dpasse pas la valeur spcifie et qu'elle soit correctement rgle. 5. Ne pas utiliser un tube-image autre que celui spcifi et ne pas effectuer de modifications dconseilles du circuit haute tension. 6. Lors de la recherche des pannes et des mesures d'essai sur un rcepteur qui prsente une haute tension excessive, viter de s'approcher inutilement du rcepteur. Ne pas faire fonctionner le rcepteur plus longtemps que ncessaire pour localiser la cause de la tension excessive.
AVERTISSEMENT
1. N'entreprendre aucune modification de tout circuit. C'est dangereux. 2. Dbrancher le rcepteur avant toute rparation. 3. Les dversoirs thermiques semi-conducteurs peuvent prsenter un danger de choc lectrique lorsque le rceqteur est en marche. 4. Le chssis de ce rcepteur a deux systmes de mise la terre qui sont spars par un matriau isolant. Le systme de mise la terre non-isole (chaud) est pour le circuit du rgulateur de tension B+ et le circuit de sortie horizontale. Le systme de mise la terre isol est pour les basses tensions C. C. B+ et le circuit secondaire du transformateur de haute tension. PRECAUTION:POUR LA PROTECTION CONTINUE CONTRE LES RISQUES D'INCENDIE, REMPLACER LE FUSIBLE PAR UN FUSIBLE DE MEME TYPE 4A-125V.
4A 125V
REPARATION DU SYSTEME A HAUTE TENSION ET DU TUBE-IMAGE Lors de la rparation de ce systme, supprimer la charge statique en branchant une rsistance de 10 k en srie avec un fil isol (comme une sonde d'essai) entre la mise la terre du tube-image et le fil d'anodel. (Le corden d'alimentation doit tre retir de la prise murale.)
1. Il est noter que le tube-image de ce rcepteur est intgralement protg contre l'implosion. 2. Par mesure de scurit, changer le tube-image pour un tube du mme numro de type. 3. Ne pas lever le tube-image par son col. 4. Ne manipuler le tube-image qu'en porant des lunettes incassables et qu'aprs avoir dcharg totalement la haute tension.
13VT-N200
Voltmtre CA
1.5k ohm 10W
13VT-N200
ELECTRICAL SPECIFICATIONS
TV SECTION POWER INPUT: POWER RATING: PICTURE SIZE Width: Height: Depth: CONVERGENCE: SWEEP DEFLECTION: FOCUS: INTERMEDIATE FREQUENCIES Picture IF Carrier Frequency: Sound IF Carrier Frequency: Color Sub-Carrier Frequency: AUDIO POWER OUTPUT RATING: SPEAKER Size: Voice Coil Impedance: VHF/UHF ANTENNA INPUT IMPEDANCE: TUNING RANGES VHF-Channels: UHF -Channels: CATV Channels: VCR SECTION Format: Video Recording System: Number of Video Heads: Video Signal Standard: Tape Width: Tape Speed: VHS Standard Rotary Two-Head Helical Scanning 4 pcs. NTSC Color System 12.7mm (1/2inch) (SP)33.35mm/sec (1.31 i.p.s) (LP)16.67mm/sec (0.66 i.p.s) Play back only (EP)11.12 mm/sec (0.44 i.p.s) (SP)160 min (T-160) (EP)480 min (T-160) 0.5 to 2.0 Vp-p, 75 ohm unbalanced -8 dB, 47k ohm unbalanced (0 dB-0.775 Vrms) 5C to 40C (41F to 104F) -20C to 60C (-4F to 140F) 120 V AC 60 Hz 65 W 37.8 cm 38.7 cm 38.2 cm Magnetic Magnetic Hi-Bi-Potential Electrostatic 45.75 MHz 41.25 MHz 42.17 MHz (Nominal) 0.8 W (at 10% Distortion) 5 9 cm (2" 31/2") 16 ohm at 400 Hz 75 ohm unbalanced 2 thru 13 14 thru 69 1,14 thru 125 (EIA, Channel Plan)
Maximum Recording Time: Video Input: Audio Input: Operating Temperature: Storage Temperature:
13VT-N200
POWER
REC
REC
TAMPER PROOF indicator PROGRAM TIMER indicator REC indicator POWER indicator
PLAY button
STOP/EJECT button
REAR
13VT-N200
DISPLAY Used to change the On Screen Display. MUTE Press Mutes sound. Press again Restores sound to previous level. Press the MUTE button to enter the CLOSED CAPTION mode automatically if the signal contains CC information. VOLUME UP/DOWN
CH
POWER
INPUT DISPLAY MUTE
VOL
1 4 7
FLASHBACK
2
5
3 6 9 100
TAPE SPEED TAMPER PROOF
8 0
COUNTER RESET
TR
CHANNEL UP/DOWN (TRACKING / ) Used to select the CHANNEL. Used to adjust the TRACKING while playing the tape. TAMPER PROOF Used to block changes to current operating mode. FF Used to fast forward the tape or to conduct Forward Video Search during playback mode. STOP Used to stop the tape. PAUSE/STILL Used to temporarily stop the tape during recording mode. Used to display a still picture during playback mode. DPSS ( / ) Press the ( / ) button to search for the index signal and begin playback automatically. Press the ( / ) button to vary the slow motion speed during slow mode. PROGRAM Press the button to enter the Timer Recording mode. MENU Used to select the menu screen.
PLAY
REW STOP
FF
REC
PAUSE/STILL
DPSS
F.ADV
TIMER ON/OFF
SLOW
PROG
CONFIRM
RETURN
SET
MENU
With your thumb nail, pull up the slit as indicated by the arrow to remove the back cover. Insert two batteries (size AA). Be sure to match the battery / terminals with the / marks inside the compartment.
13VT-N200
K
M
13VT-N200
8 9
10
13VT-N200
GC
PG PG SP OR
OR OC
GR K GC GR
OC
M
FRONT
11
13VT-N200
CIRCUIT PROTECTION
The receiver is protected by a 4.0A fuse (F701), mounted on PWB-A, wired into one side of the AC line input.
12
13VT-N200 The L-series SHARP TV/VCR COMBINATION have most of the analog setup adjustments eliminated. Coil and variable resistor adjustments are now performed digitally by using the remote controller or sets volume and channel change function buttons. Note: There are still a few analog adjustments in the L-series such as 120V adjust, focus, master screen voltage and coils in the picture IF/detector circuit. Follow the steps below, whenever service adjustment is required. See "Table-B" to determine, if service adjustments are required.
1. Service mode
Berfore putting unit into the service mode, check that customer adjustments are in the normal mode, use the reset function in the video adjust menu to ensure customer controls are in their proper (reset) position.
PICTURE: 16
13
13VT-N200 Table - A ADJUSTMENT ITEM PICTURE TINT COLOR BRIGHT SHARP PHASE H-PHASE RF-AGC V-AMP PIF-VCO R CUT-OFF G CUT -OFF B CUT-OFF G GAIN B GAIN MUTE ENERGY SAVE BALANCE TEXT BOX TEXT PICTURE CCD LEVEL OPTION DATA INTIAL VALUE RANGE 16 0~63 39 0~77 13 0~63 32 0~63 7 0~13 0 0~7 20 0~31 18 0~63 32 0~63 40 0~127 0 0~255 0 0~255 0 0~255 128 0~255 128 0~255 0 0~2 45 32 15 20 7 39 0~45 0~63 0~127 0~80 0~10 0~63 ADJUSTMENT COMMENTS
*No adjustment is required due to proper setting being made by IC2001 automatically. Table - B PART REPLACED IC2001 IC401 IC2101 CRT X X X ADJUSTMENT NECESSARY UNNECESSARY X Data is stored in IC2003. The adjustment is needed to compensate for characteristics of parts including IC401. Initial setting values are written from IC2001. Adjust for best results. Adjust items related to picture tube only. NOTE
14
13VT-N200
RF AGC Adjustment
1. Have unit receive a good local channel. 2. Enter the service mode and select service adjustment item "RF-AGC". 3. Set the data value to point where no noise or beat appears. 4. Select another channel to confirm that no noise or beat appears. Note 1: You will have to come out of the service mode to select another channel. Note 2: Setting the data to "0" will produce a black raster.
Picture Adjustment
1. Have unit receive a good local channel. 2. Make sure the customer picture control is set to maximum. 3. Enter the service mode and select service adjustment item "PICTURE". 4. Adjust the data value to achieve normal contrast range.
Tint Adjustment
1. Have unit receive a good local channel. 2. Set customer tint control to center of its range. 3. Enter the service mode and select service adjustment item "TINT". 4. Adjust "TINT" data value to obtain normal flesh tones.
Screen Adjustment
1. Select a good local channel. 2. Enter the service mode and select service adjustment item "COLOR" and set the data value to "0" to set the color level to minimum. You may skip this step, if you selected a B/W picture or monoscope pattern. 3. Select service adjustment item "Y-MUTE" and adjust the data value to "1", this turns off the luminance signal (Y-mute). 4. Select service adjustment item "BRIGHT" and set the value to "32". 5. Adjust the master screen cotrol untill raster darkens to the point where raster is barely seen. 6. Adjust service adjustments item "R-CUT OFF" red "G-CUT OFF" green and "B-CUT OFF" blue to obtain a good grey scale with normal whites at low brightness level. 7. Select service adjustment item "MUTE" and reset data to "0". Select service adjustment item "COLOR" and reset data to obtain normal color level.
Color Adjustment
1. Have unit receive a good local channel. 2. Make sure the customer color control is set to center position . 3. Enter the service mode and select service adjustment item "COLOR". 4. Adjust "COLOR" data value to obtain normal color level.
Brightness Adjustment
1. Have unit receive a good local channel. 2. Make sure the customer brightness control is set to center position. 3. Enter the service mode and select service adjustment item "BRIGHT". 4. Adjust "BRIGHT" data value to obtain normal brightness level.
15
13VT-N200
Vertical-Size adjustment
1. Have unit receive a good local channel. 2. Enter the service mode and select service adjustment item "V-AMP". 3. While observing the top and bottom of the screen, adjust "V-AMP" data value to proper vertical size and linearity.
Figure B.
16
13VT-N200
PRECAUTIONS IN REASSEMBLING
MOUTING THE CASSETTE CONTROLLER
Initial setting is indispensable before placing the cassette controller in the mechanism. The initial setting is made in two ways;electrical and mechanical.
Electrical setting:
Make a short-circuit between TP7701 and TP7702 and be sure that the mechanism is back to its initial setting position (*1). Now place the cassette controller in position.(This method is used when the mechanism has been already set on its PWB.)
Pulley feed gear
Screwdriver
Large tooth
Mechanical setting:
Turn the loading motors pulley feed gear using a screwdriver and be sure that the mechanism is back to its initial setting position (*1). Now place the cassette controller in position.(This method is applicable for the mechanism alone.)
AC Connector
AL Connector
START SENSOR
17
13VT-N200
Drum Ass'y 17
21 Take-up Pole Base Ass'y 20 Automatic Head Cleaner Ass'y Drum Motor 19 11 A/C Head Ass'y 22 Fixing Guide
16 Full Erase 1 Head Supply Pole Base Ass'y 2 Sup Main 7 Brake Ass'y Tension 3 Arm Ass'y
10 Pinch Drive Cam 13 Reverse Guide Lever Ass'y 8 Pinch Drive Lever Ass'y Casecon Drive Gear
14
18 Loading Motor
No.
1.
Function
Full erase head assy Erase the old recording on the tape in the recording mode. Tension arm assy Detects the tension of tape while running, and brakes the supply reel disk via the tension band. Sup Main brake lever Brakes the supply reel disk to prevent tape slackening when the unit is stopped in fast forward or rewind mode. Main take-up brake lever Brakes the take-up reel disk to prevent tape slackening when the unit is stopped in fast forward or rewind mode.
No.
13.
Function
Reverse guide lever assy Pulls out the tape and controls the tape drive train height with the upper and lower guides.
3.
16.
Pinch roller lever assy Press-fits the tape to the capstan during tape running.
7.
18.
9.
Loading motor A motive power which drives the mechanism. It transmits the power to the master cam and cassette housing control ass'y.
18
13VT-N200
Capstan D. D. Motor 3
Drive Belt 4
8 Shifter
5 Clutch Lever
No.
1.
Function
Slow brake Gets in contact with the capstan D.D. motor linking to the master cam in the slow still mode, and brakes it to a certain degree. Capstan D.D. motor A motive power which runs the tape. It transmits the power via the Drive belt.
No.
6.
Function
Limiter pulley assy Transmits the power of the capstan D.D. motor to the reel disk via the drive idler. Shifter Transmits the operation of the master cam to break assy, Ioading gear, tension arm and clutch lever. Take-up loading gear Shifts the take-up pole base and guide roller via the loading gear T, and applies the tape around the drum assembly, as well as transmits the power to the loading gears.
8. 3.
9. 4. Drive belt Transmits the power to run the tape to the Limiter pulley.
19
13VT-N200
1.
JiGVHT-063
CZ
CM CN These Jigs are used for checking and adjusting the torque of take-up and supply reel disks.
3.
JiGTH0006
AW
4.
Torque Driver
JiGTD1200
CB
When fixing any part to the threaded hole using resin with screw, use the jig. (Specified torque 5 kg)
5.
BR BY BS BF
These Jigs are used for checking and adjusting the reel disk height.
6.
There are two gauges used for the tension measurements, 300 g and 2.0kg. This Jig is used with the tension gauge. Rotary transformer clearance adjusting jig. These Jigs are used for loosening or tightening special hexagon type screws. This Jig is used for height adjustment of the reverse guide (for reverse guide height adjustment).
7.
JiGADP003
BK
JiGHW0012 JiGHW0015
AE AE
9.
JiGDRiVER11055
AR
20
13VT-N200
No.
Jig ltem
Part No.
Code
Configuration
Remarks These tapes are especially used for electrical fine adjustment.
Video Audio 7k 1k 7k 1k Hi-Fi Audio Track 58m 58m 46/58 m 19m
CD CB
JiGDRiVERH-4
AP
12.
JiGDRiVER-6
BM
13.
JiGRVGH-F18
BU
21
13VT-N200
Reel belt Tension band assy Loading Motor Idler assy Limiter pulley Supply/take-up Main brake levers NOTE: : Part replacement. : Cleaning : Oil refilling <Specified> Cleaning liquid Industrial ethyl alcohol
* This mechanism does not need electric adjustment with variable resistor. Check parts. If any deviation is found, clean or replace parts.
22
13VT-N200
Notes: 1. When fitting the S/E sensor holder to the cassette controller frame L/R, take care. 2. Misengagement of teeth of casecon drive gear and drive angle gear causes malfunction. (The cassette cannot be set, load and ejection are repeated). 3. In the case when you use the magnet screw driver, never approach the magnet driver to the A/C head, FE head, and drum. 4. When installing or removing, take care so that the cassette housing control and tool do not contact the guide pin or drum. 5. After installing the cassette housing control once perform cassette loading operation.
Figure 1-1.
Reassembly 1. Before installing the cassette housing control, shortcircuit TP7701 and TP7702 provided at the left of the main PWB, prug in the power cord. The casecon drive gear turns and stops when the positioning mark appears. Engage two teeth of casecon drive gear with the three teeth of casecon drive angle gear, and set on the mechanism chassis as shown below.
500g
Mechanism chassis
Figure 1-3.
Notes: 1. The weight should not be more than 500g. 2. Take care not to damage the tape when the Cassette is set in the mechanism shassis or taken out of it because the supply/take-up poles are shifted foward the tape loading direction in the EJECT position.
23
13VT-N200
4. Assemble the Sup main brake ass'y. Notes: 1. When installing the reel disk, take due care so that the tension band ass'y is not deformed and grease does no adhere. 2. Do not damage the Sup main brake ass'y. Be careful so that grease does not adhere to the brake surface. Reassembly (Take-up reel disk) 1. Clean the reel disk shaft and apply grease (SC-141) to it. 2. Align the phase of the reel disk to that of the reel relay gear and to install a new take-up reel disk onto the shaft. 3. Check the reel disk height and reassemble the take-up main brake ass'y. Notes: 1. Take care so that the Tu main brake ass'y is not damaged. Take care so that grease does not adhere the brake surface. 2. After reassembly, check the video search rewind back tension (see page 27), and check the brake torque (see page 29). Height checking and adjustment Notes: 1. Set the master plane with due care so that it does not contact the drum. 2. When putting the master plane, shift the reverse guide a little in the loading direction. Care must be taken since excessive shift results in damage.
Figure 1-4. Note: When the tension band ass'y is pressed in the direction of the arrow for removal, the catch is hard to be deformed.
Supply reel disk Cassette lock release shaft Take-up reel disk Position pin
Figure 1-6. Figure 1-5. Reassembly (Supply reel disk) 1. Clean the reel disk shaft and apply grease (SC-141) to it. 2. Match the phases of reel disk and reel relay gear, and set the new reel disk. 3. After checking the reel disk height, wind the tension band ass'y around the reel disk, and insert into the hole of tension arm ass'y.
Note: Check that the reel disk is lower than part A but higher than part B. If the height is not correct, readjust the reel disk height by changing the poly-slider washer under the reel disk.
24
13VT-N200 Note: Whenever replacing the reel disk, perform the height checking and adjustment.
Master plane Reel disk height adjusting jig Mechanism chassis
A
Notes: 1. Hold the torque gauge by hand so that it is not moved. 2. Do not keep the reel disk in lock state. Do not allow long-time measurement.
10 0.2mm
Reel disk
B
Reel disk
Figure 1-7.
Torque gauge
The gauge is held at its maximum value. (Red mark) Idler ass'y
Figure 1-9.
Idler ass'y
Figure 1-8. Adjustment 1. If the FF winding-up torque is less than the specified value, clean the capstan D.D. motor pulley, drive belt, and limiter pulley with cleaning liquid, and check again. 2. If the torque is less that the set value, replace the reel belt.
Adjustment 1. If the rewind winding-up torque is less than the specified value, clean the capstan D.D. motor pulley, drive belt, and limiter pulley with cleaning liquid, rewind again, and check the winding-up torque. 2. If the winding-up torque is still out of range, replace the drive belt.
25
13VT-N200 Notes: 1. Hold the torque gauge by hand so that it is not moved. 2. Do not keep the reel disk in lock state. Do not allow long-time measurement.
CCW
500g
Figure 1-10. Checking 1. Make sure that value is within the setting 6.9 2.5mNm (70 25gfcm). 2. The winding-up torque fluctuates due to variation of rotation torque of limiter pulley ass'y. Read the center value of fluctuation as setting. 3. Set the EP record mode (x3) and make sure that the winding-up torque is within setting. Adjustment If the playback winding-up torque is not within the setting, replace the limiter pulley assembly. Note: When the torque cassette is set, put a weight (500g) to prevent rise. Figure 1-11.
Note: Surely put the torque gauge on the reel disk to measure. If the torque gauge is raised, accurate measurement is impossible. Adjustment 1. If the rewinding playback winding-up torque is not within the setting, replace the limiter pulley assembly. Note: The winding-up torque fluctuates due to variation of rotation torque of supply reel disk. Read the center value of fluctuation as setting.
26
13VT-N200
Figure 1-13. 1. Detach the pinch roller from the capstan shaft. Do not separate excessively. Or the pinch lever and pinch double action lever may disengage. 2. Engage the tension gauge adapter with the pinch roller shaft, and pull in the arrow direction. 3. Gradually return the pinch roller, and measure the pulling force when the pinch roller contacts the capstan shaft. 4. Make sure that the measured value is within setting 0.9 to 11.8 N (900 to 1,200g).
CCW
500g
Figure 1-14. Checking 1. Set a cassette tape, push the REC button to place the unit in the SP record mode. Now check the tension pole position.
27
13VT-N200 2. Visually check to see if the right edge of the tension pole is within the 1.5 0.25mm from the right edge of the Sup guide shaft. Tension pole adjuster adjusting range
Tension pole adjuster
90
90
Figure 1-18.
Adjust so that the delta mark of tension pole adjuster is within 90 range (left, right).
1.5 0.25mm
Figure 1-16. Insert the slotted screwdriver in the tension pole adjuster, and rotate counterclockwise. At right side from the center line
500g
1.5 0.25mm
Figure 1-17. Insert the slotted screwdriver in the tension pole adjuster, and rotate clockwise.
Figure 1-19.
Checking 1. Push the REC button to place the unit in the SP record mode. 2. At this time ascertain that the back tension is within the setting (36.5 to 52gcm) by seeing the indication of torque cassette meter.
28
13VT-N200 Adjustment 1. If the indication of torque cassette meter is lower than the setting, shift the tension spring engagement to the part A. 2. If the indication of torque cassette meter is higher than the setting, shift the tension spring engagement to the part B.
A Tension arm B CW Take-up reel disk CCW
Torque gauge
Tension spring
Figure 1-20.
After short-circuiting TP7701 and TP7702 provided at the left on the main PWB, plug in the power cord, then turn on the power. 1. 2. 3. Setting Switch from the FF mode to the STOP mode. Disconnect the power cord. Set a torque gauge to zero on the scale. Place it on the take-up reel disk.
Figure 1-21. Remove the cassette housing control assembly. After short-circuiting TP7701 and TP7702 provided at the left on the main PWB, plug in the power cord, then turn on the power. Setting 1. Set a torque gauge to zero on the scale. Place it on the supply reel disk. 2. Switch from the FF mode to the STOP mode. 3. Disconnect the power cord. Checking Turn the torque gauge at a rate of about one turn/2 sec in the CW direction/CCW direction with respect to the supply reel disk so that the reel disk and torque gauge pointer rotate at equal speed, and make sure that the value is within the setting (CW direction: 8.8 to 23.5mNm (90 to 240gfcm); CCW direction: 3.9 to 9.8mNm (40 to 100gfcm).
Checking 1. Turn the torque gauge at a rate of about one turn/2 sec in the CCW direction/CW direction so that the reel disk and torque gauge pointer rotates at equal speed and make sure that the value is within the setting (CCW direction: 8.8 to 23.5mNm (90 to 240gfcm), CW direction: 4.9 to 11.8mNm (50 to 120gfcm). 2. Adjustment of the brake torque at the supply side and the take-up side Unless the supply side brake torque or take-up side brake torque is within the setting, clean the felt surface of reel disk (supply, take-up) brake lever, check again the brake torque. If value cannot be set within the setting yet, replace the main brake ass'y or main brake spring.
29
13VT-N200
3. Align the left end of gear of A/C head arm with the punched mark of chassis, tentatively tighten the screws 1 and 2 so as to ensure smooth motion of A/C head arm. Tentative tightening torque must be 0.15 to 0.20 Nm (1.5 to 2.0kgfcm).
Height screw 3 Tilt screw Azimuth screw 2 Left end of A/C head arm gear Punched line mark on chassis
Figure 1-25.
Height screw Spring 1
Notes: 1. If the screws 1 and 2 are tighten tentatively too loose, the azimuth and height of A/C head may change when they are finally tightened. Therefore care must be taken. 2. After completion of A/C head be sure to adjust tape running. (Execute the running adjustment by the method described in Page 32, 33.)
Figure 1-23.
Replacement 1. Solder the removed PWB to the new head assembly. 2. Adjust the height from the A/C head arm (lower surface) to the A/C head plate to 10.8mm with slide calipers. (3 places of azimuth screw section, tilt screw section and A/C head front section) (See the figure below.)
Solder
New A/C head ass'y A/C head PWB Never touch the head A/C head plate
10.8mm
10.8mm
Figure 1-24.
30
13VT-N200
Height screw
Cassette tape
Mechanism chassis
13.38mm
(b)
Mechanism chassis
2. Rotate counterclockwise the reverse guide height adjustment nut 1/10 turn. (For height adjustment use the reverse guide height adjustment box driver (JiGDRiVER11055)).
Figure 1-26.
Box driver
1. Set the cassette tape in the unit. 2. Press the PLAY button to put the unit in the playback mode. 3. Roughly adjust the height of the A/C head by turning the height screw until the tape is in the position shown below.
A/C head
CCW
Tape 0.3mm
Figure 1-29. 3. Set the tape, and check for tape crease near the reverse guide in the playback mode. If crease is found, turn the reverse guide adjustment nut to remove crease. (As for crease check refer to Figure 1-30.)
A Capstan motor shaft Fixing guide Mechanism chassis Reverse guide
Figure 1-27. Adjustment Adjust the height screw visually so that the control head is visible 0.3mm below the bottom of the tape.
500g
31
13VT-N200
Notes: 1. Previously set the tracking control in the center position, and adjust the envelope waveform to maximum with X value adjustment nut. Thereby the tape run rough adjustment is facilitated. 2. Especially the outlet side envelope waveform must have higher flatness.
Figure 1-32. 2. Adjustment of A/C head height and azimuth 1 Perform the initial setting of A/C head position by the method stated in "Page 30 Replacement 3". 2 Connect the oscilloscope to the audio output (TP6601). 3 Using the alignment tape in which 1 kHz linear audio signal has been recorded, adjust the height screw so as to get max audio output. 4 Using the alignment tape in which 7 kHz linear audio signal has been recorded, adjust the azimuth screw so as to get max audio output.
500g
Weight of 500g
Figure 1-31. 7 Press the tracking button (+), () and change the envelope waveform from max to min and from min to max. At this time make sure that the envelope waveform changes nearly parallel. 8 Unless the envelope waveform changes nearly parallel, adjust the height of supply side and takeup side guide roller so that the envelope waveform changes nearly parallel. (For envelope adjustment procedure refer to Figure 1-35.) 9 Turn the tilt screw to remove the tape crease at the fixing guide flange. Play back the tape and check for tape crease at the fixing guide flange. (1) If there is no tape crease Turn the tilt screw clockwise so that tape crease appears once at the flange, and then return the tilt screw so that the crease disappears. (2) If there is tape crease Turn counterclockwise the tilt screw so that the tape crease disappears. (Reference) If the tilt screw is turned clockwise crease appears at the lower flange.
For X value adjustment Adjust the X value, turning the geartype screwdriver.
Figure 1-33.
32
13VT-N200 3. Tape run adjustment 1 Connect the oscilloscope to PB CHROMA envelope output test point, set oscilloscope sync to EXT, trigger-input the PB CHROMA signal (head switching pulse). 2 Rough adjustment of X value Tentatively fix A/C head arm screws 1 and 2 by the method described in Page 30 "Replacement 3". After shortcircuiting TP7701 and TP7702, plug in the powercord, then turn on the power. And playback the alignment tape (VRONBZGS). As a result the autotracking is automatically cancelled, so that the X value adjustment mode is set. Move the A/C head with the X value adjustment gear driver (JiGDRiVER-6) by the method shown in Figure 1-33, and adjust the A/C head so as to get the maximum envelope waveform. (Note: When the A/C head is adjusted, adjust so that the maximum envelop waveform is obtained nearest the position of initial setting made in Page 30.) 3 Next, change the alignment tape to VROEFZCS to play back. Press the tracking button (+), () and change the envelope waveform from max to min and
PB CHROMA Envelope
CH-1
CH-2
Head switching pulse Figure 1-34. from min to max. At this time adjust the height of supply and take-up side guide roller with the adjustment driver (JiGDRiVERH-4) so that the envelope waveform changes nearly parallel. 4 If the tape is lifted or sunk from the helical lead surface, the PB CHROMA envelope waveform appears as shown in Figure 1-35. 5 Press the tracking button (+), () and make sure that the envelope waveform changes nearly parallel. 6 Finally check tape crease near the reverse guide. If tape crease is found, remove it as stated in Page 31 "HEIGHT ADJUSTMENT OF REVERSE GUIDE" item 3. When the tape is below the helicallead. Supply side Take-up side
When the tape is above the helical lead. Supply side Take-up side
Adjustment
Supply side guide roller rotated in clockwise direction (lowers guide roller) to flatten envelope.
Take-up side guide roller rotated in clockwise direction (lowers guide roller) to flatten envelope.
Supply side guide roller rotated in counterclockwise direction (raises guide roller) to make the tape float above the helical lead. The supply side guide roller is then rotated in the clockwise direction to flatten the envelope.
Take-up side guide roller rotated in counterclockwise direction (raises guide roller) to make the tape float above the helical lead. The take-up side guide roller is then rotated in the clockwise direction to flatten the envelope.
Figure 1-35. 4. A/C head X value adjustment 1 Tentatively fix A/C head arm screws 1 and 2 by the method described in Page 30 "Replacement 3". 2 After shortcircuiting TP7701 and TP7702, plug in the powercord, then turn on the power. And playback the alignment tape (VROEFZCS). As a result the autotracking is automatically cancelled, so that the X value adjustment mode is set. 3 Move the A/C head with the X value adjustment gear driver by the method shown in Figure 1-33, and adjust the A/C head so as to get the maximum envelope waveform. (Note: At this time adjust so as to get the maximum envelope waveform nearest the A/C head position which has been set in case of X value rough adjustment as stated in Page 33, 3- 2.) 4 Tighten finally the screws 1 and 2. Be sure to tighten at first the screw 1 and then the screw 2. Final tightening torque is 0.6Nm (If the screw 2 is tightened first, the X value may deviate.) 5 Adjust the playback switching point (Refer to the electric adjustment method.) 6 Playback the self-picture-recorded tape, and check the flatness of envelope waveform and sound. Note: When the A/C head X value adjustment is performed, be sure to perform at first X value rough adjustment (refer to Page 33, 3-2). 1
2
Figure 1-36.
33
13VT-N200
Notes: 1. In removing the D.D. stator assembly, part of the drum earth spring pops out of the pre-load collar. Be careful not to lose it. 2. Install, so that the D.D. rotor ass'y and upper drum ass'y mounting direction check holes align. (Align the upper drum dent with the rotor hole.) 3. Be careful not to damage the upper drum or the video head. 4. Protect the hole elements from shock due to contact with D.D. stator or D.D. rotor ass'y. 5. After installation adjust the playback switching point for adjustment of servo circuit.
Reel belt
Figure 1-37.
3 1 FFC 4
2. Remove the three screws 2. Reassembly 1. Taking care so that the capstan shaft does not contact the mechanism chassis, set its position on the mechanism chassis, and then install with the three screws. 2. Install the reel belt. Notes: 1. After installing the capstan D.D. motor, be sure to rotate the capstan D.D. motor and check the movement. 2. Set the tape, and check for the tape crease near the reverse guide in the playback mode. Adjust the A/C head and azimuth as stated in Page 32 item 2. If crease is found, adjust as stated in Page 31 "HEIGHT ADJUSTMENT OF REVERSE GUIDE".
Upper drum
Figure 1-38.
34
13VT-N200
[Cares when replacing the drum] 1. Be careful so that the drum earth brush is not lost. 2. Do not touch directly the drum surface. 3. Fit gently the screwdriver to the screws. 4. Since the drum assembly is an extremely precise assembly, it must be handled with utmost care. 5. Make sure that the drum surface is free from dust, dirt and foreign substances. 6. After replacing the drum be sure to perform the tape running adjustment. After that, perform also the electrical adjustment. Playback switching point adjustment X-position adjustment and check 7. After replacing the drum clean the drum.
7 2 1 6
4 3 2 1
Figure 1-39.
Figure 1-40.
35
Align here.
Fit the pinch drive cam so that the notch of pinch drive cam aligns with the dent of pinch drive lever assembly.
Fit the pinch drive cam so that the notch of pinch drive lever assembly aligns with the half-round notch of chassis. Pinch drive lever ass'y
Figure 1-41-1. 2Insert Pinch Roller/Pinch Double Action Lever Assy. 3Insert Open Lever.
Open lever Pinch Roller Double Action Lever Ass'y Phase Matching Point 2
Figure 1-41-2.
Figure 1-41-3.
36
13VT-N200
1. Make sure that the loading gear is at the point 1 as shown below. 2. Install, paying attention to 6 insertion points and 3 release points. 3. For the phase matching at the insertion point 1, see the point 2 as shown below. 4. Finally fix the inserts 1 and 4.
Reel pulley
Figure 1-42.
Phase-Matching point 2 Loading gear (T) Round mark Insert point 1 Shaft 1 Half round notch
Sifter
Insert point 3
Insert point 2
Insert point 4
Shaft 1
Insert point 6
Phase-matching point 1
Shaft 1
Release point 3
Figure 1-43.
37
13VT-N200
Apply grease
No grease Fully turn counterclockwise Face the wide tooth side ward
Figure 1-44-1.
Note: See the figure below for the phase matching between the master cam and the casecon drive gear. 3. Finally fix with the E-ring.
Figure 1-45.
Master cam
Replacement 1. Remove the loading motor, and install the replacement loading motor as shown below.
When installing the master cam, align the casecon drive gear round mark with the half-round notch of master cam.
Figure 1-46. The loading motor pressing-in must be less than 14.7 N (15 gf). Adjust the distance between motor and pulley to 10.2 +0.2 mm). 0.2
Figure 1-44-2.
38
13VT-N200
MSPRT0381AJFJ
Apply grease
Figure 1-47.
Drive angle
Drive gear R
Frame
Figure 1-48.
39
13VT-N200
5.50.5H(Iines)
V-sync.
Figure 2-1.
1. Play the alignment tape.(VROATSV.) 2. Press the CH " (TR ) button and the "0" button of remote control at the same time to turn the set into the adjustment mode for head switching point and to set the tracking to center. (See Notes below) "T" is displayed on the TV screen. 3. Press the PLAY button of remote control to make the adjustment of head switching point, then the leading edge of the head switching pulse is automatically set 5.5H (lines) ahead of the vertical sync as shown Figure 2-1 and the adjustment data is memorized in the E2PROM IC. 4. Then press the stop button to stop the tape.
Notes: 1 To make this adjustment, disable the AUTO TRACKING function. The AUTO TRACKING function is disable in the following cases. (In the playback mode only.) a When the CH " (TR ) button and the "0" button of the remote control are pressed at the same time. b When the AC cord is plugged in with making TP7701 and TP7702 short circuited, after the cassette housing control ass'y is removed. (Mechanism operating mode) The AUTO TRACKING function becomes available in the following cases. a When the CH ' (TR ) button and the CH" (TR ) button of the remote control are pressed at the same time. b When the AC cord is plugged in with the cassette housing control ass'y put back. 2 Pressing both the CH " (TR ) and the "0" button transmits the test code. When the unit receives this test code in the playback mode, the unit is turned into the adjustment mode for the head switching point and "T" is displayed at the position of CH number on the screen. This function is available to the remote control RRMCG1331PESA.
40
Figure 2-2.
41
ELECTRICAL TROUBLESHOOTING
CASSETTE CONTROL TROUBLESHOOTING FLOW CHART NO.1-1 A cassette tape is not taken in. FLOW CHART NO.1-3
13VT-N200
The VCR is dead.(No power) Is the cassette housing distored? YES Fix or replace the cassette housing.
Unplug the AC power cord. Replug it a few minutes later. YES Check power circuit. NO
NO Does the start sensor cover become open when the cassette tape is inserted? NO
Check the start sensor and the way up to pin (5) of IC2001.
Check pin (21) of IC2001 and all the way up to pin (5) of IC7701.
Are the AT 5V and AT 12V NO lines normal? YES Are the AT 5V and GND NO lines properly connected with IC2001? YES Is there oscillation NO (16MHz) at pins (38) and (39) of IC2001? YES Check/replace X7701 and/or IC2001. NO Check power circuit. NO
NO
Check the sensor inputs to IC2001 from mechanism. (CAM switches,start/end sensors,and reel sensors) FLOW CHART NO.1-2
YES Does the start sensor pin (5) of IC2001 go to "L" level when the cassette tape is inserted? YES Does pin (5) of IC7701 (BA6209) go to "H" level (about 1.8V) when the cassette tape is inserted? YES Does pin (2) of IC7701 go to about11V when the cassette tape is inserted? YES Is the correct voltage at the loading motor terminal when the cassette tape is inserted? YES Check and replace the loading motor. A cassette tape is taken in, but ejected at once.
42
Check the switch contact. Check IC2001 and switches for poor soldering. YES Check key lines to input IC2001. Do the cam switches A and B operate normally when the cassette tape is loaded? YES Replace IC2001
KEY-IN TROUBLESHOOTING
NO
YES
NO
Does start sensor pulse at pin (5) of IC2001 change from "L" to "H" NO level when the cassette tape is loaded? YES Does end sensor pulse at pin (6) of IC2001 change from "L" to "H" NO level when the cassette tape is loaded?
NO
Are signals received at pin (8) of IC2001 when the key is activated? YES
NO
Check IC2001.
NO See FLOW CHART NO.1-6. NO Does power control (H) signal at pin (31) of IC2001 change from "L" to"H" level? YES Is the PC9V line normal? YES Check the take up reel sensor and all the way to IC2001. Is the PC5V line normal? NO NO
Check IC2001.
NO
NO
Does the capstan motor start when the EJECT button is pressed? YES Does the take-up reel disk turn when the capstan motor is running? YES Is reel pulse at pin (80) of IC2001 when the take-up reel disk is turning? YES Is "H" level (about 1.8V) at pin (6) of IC7701 when reel pulse is inputted? YES Check between pin (6) of IC7701 and all the way up to pin (20) of IC2001. Check IC7701 and "L" level of pin (5) of it. Check between IC7701 and all the way up to the loading motor. Replace the loading motor. YES Check peripheral circuit for poor soldering of PC9V and PC5V lines. CAPSTAN MOTOR TROUBLESHOOTING The capstan motor fails to run.
NO
NO
NO
43
YES
NO
NO
YES Is the voltage more than about 2.6V given to pin (4) of AC connector? YES Is the voltage at pin (3) of AC connector 1.8~2.7V? YES Is 8V or 12V at pin (5) of AC connector? YES Check/replace the capstan motor.
NO
Check between the MC connector and IC2001, and between the MC connector and pin (76) of IC2001. NO Check pin (74) of IC2001
NO
13VT-N200
TAKE-UP REEL PULSE GENERATOR TROUBLESHOOTING FLOW CHART NO.1-7 DRUM MOTOR TROUBLESHOOTING FLOW CHART NO.1-9 The drum motor fails to run.
13VT-N200
Is the voltage more than about 2.6V applied at pin (1) of ME connector. NO YES YES YES Is 12V at pin (4) of ME connector? YES Check/replace the drum motor. NO Check between D7702 and pin (80) of IC2001, between D7703 and pin (79) of IC2001. Is 5V at pin (7) of ME connector? NO
Check between the ME socket and pin (77) of IC2001, and between the ME socket and pin (84) of IC2001. Check the AT 5V line.
about 4.5Vp-p
Insert the cassette, and put the unit in FF or REW mode. NO Are there the take up/supply reel pulses at the collectors of D7702/D7703. NO
44
FLOW CHART NO.1-8 The drum motor runs only for a few seconds. NO See FLOW CHART NO. 1-9. Is drum PG signal at pin (5) of NO ME connector? Check the drum motor. YES Check pin (18) of IC2001 and signal line of head switching pulse. YES Is drum PG signal at pin (90) of NO IC2001? YES IS H.SW. pulse at pin (18) of NO IC2001? YES Check all the way up to pins (89) and (90) of IC2001. YES Check pin (84) of IC2001. Check or replace IC2001. Check between the ME connector and all the way up to pin (90) of IC2001.
4.2
D-PG
4.4
D-FG
Are the drum PG and drum FG signal inputted to pins (90) and (89) of IC2001, respectively? NO
Are there the drum PG and drum FG Signals at pins (3) and (5) of connector AD? NO Check the harness ADME and the drum motor unit.
Is there 16MHz oscillation at pins (38) and (39) of IC2001? NO Check X7701, C7707 and C7706. In REC mode YES
In PB mode
YES
Is there the drum PG signal at pin (90) of IC2001? YES YES See FLOW CHART NO. 1-8.
NO Check the composite sync. signal at pin (41) of IC401, Q404 and Q428.
45
Is there the drum control output at pin (77) of IC2001? NO YES Is there the drum control voltage applied to pin (1) of ME connector? YES NO Check AT 12V at pin (4) and AT 5V at pin (7) of ME connector. Check and replace the drum motor.
Check PG and FG to pins (5) and (3) of the connector ME and the drum motor.
YES
Check the signal line between pin (7) of AD and pin (84) of IC2001.
13VT-N200
13VT-N200
A Are REC and /or PB mode inoperative? YES NO Is there 16MHz oscillation at pins (38) and (39) of IC2001. Check X7701, C7707 and C7706. Check the capstan FG signal line between AC connector and IC2001. NO Does there appear the capstan FG signal at pin (87) of IC2001? YES YES Only REC mode inoperative. B
Does there appear the V- NO sync. at pin (56) at IC2001? YES Is there REC CTL signal output at pins (94), (95) of IC2001? NO
46
YES Is there capstan control signal at pin (76) of IC2001? YES NO Replace IC2001. Is there the capstan control voltage applied to pin (4) of AC connector? NO YES Is pin (78) of IC2001 normal? Replace the FFC AA-MH. YES Check " A " Replace A/C head. Check " B " In case of NO GOOD Replace the capstan motor. NO
YES
Replace IC2001.
Does CTL amplifier circuit of IC2001 (pins (95) to (97)) operate normally? (Does the noise appear at pin (97) when touch R7759 by hand?)
NO
Check the composite sync. signal at pin (41) of IC401, Q404 and Q428 up to pin (56) of IC2001.
Replace IC2001.
NO
NO
Is there a signal at pin (20) or (16) of IC2201? YES Is there a signal at NO pin (57) of IC2201? YES Check PC 5V lines. YES NO YES Are pins (36) and (35) of IC3301 at 5V? YES Is there a signal at pin (10) of IC3301? YES Check upper and lower drum. NO NO Check between pins (8) and (7) of IC2201 and all the way up thrn to pins (72) and (71) of IC2001. Is there a signal at pin (26) of IC3301? NO Check parts around pins (30) and (31) of IC2201.
NO Check IC401 and parts around it. Is there a signal at NO Check parts pin (29) of around and pins IC2201? (27), (38), (36) and (29) of IC2201. YES
NO
YES
Is there a signal at NO Check parts pin (10) of around pins (12), IC2201? (43), (45) and (10) of IC2201. YES Is there a signal at NO pin (57) of IC2201? YES Check pin (94) of IC2201. (VCO control)
Check between pin (47) of IC401 and all the way up thru to pin (20) or (16) of IC2201.
NO
Is the supply voltage of NO 5V feed to pins (4), (21), (48) and (63) of IC2201?
YES
Check between pin (25) of IC2201 and pin (14) of IC402. YES Replace IC2201.
YES Are there the I2C bus data and clock at pins (8) and (7) of IC2201?
Check between pin (57) of IC2201 and all the way up thru pin (26) of IC3301.
Replace IC3301.
47
13VT-N200
13VT-N200
Is there a signal at pin (30) NO Is the supply voltage of 5V of IC3301? feed to pin (36) of IC3301? Check PC5V line. YES Is there H.SW.P. at pin (1) of IC3301? NO Check H.SW.P. line. Replace IC3301. YES
NO
YES
YES
NO Check between pin (30) of IC3301 and all the way up to pin (57) of IC2201.
LUMINANCE NO Check the I2C bus data and clock at pins (8) and (7) of IC2201. YES
Playback is possible but CHROMINANCE without color. Is there a signal at pin (12) NO Check peripheral circuits of of IC2201? X5502.
48
Is there a signal at pin (25) of IC2201? NO
YES
Replace IC2201.
YES
Check between pin (25) of IC2201 and all the way up to pin (14) of IC402.
No E-E signal
Is there a signal at pin (87) or (91) of IC2201? Is there "H" level at pin (70) of IC2201? YES Is there a signal at pin (81) of IC2201? YES NO
NO Check circuits around the audio output circuit in IC401 and parts around the audio inputs jack (J401).
NO
After there the I2C bus data and clock signal at pins (8) and (7) of IC2201? NO YES Replace IC2201. Check the I2C bus data and clock signal line.
YES Are there the I2C bus data and clock signal at pins (8) and (7) of IC2201? YES Is voltage of pins (86) and (88) of IC2201 normal? YES YES Is there a signal (Bias) at pin (6) of T6601? YES Is there a signal (Bias+Audio sig.) at pin (4) of connector AA? YES Check FFC MH-AA and A/C head. NO NO Is there "H" level at pin (72) of IC2201? YES Check A-MUTE (H) Line. (IC2201 pin (72)~ IC2001 pin (29)). Replace IC2201. NO Is there "H" level at pin (2) of T6601? NO
NO Check between pins (8) and (7) of IC2201 and all the way thru to pins (72) and (71) of IC2001.
NO
Check PC 9V line.
YES
Check T6601, Q6603, Q6604 and their peripheral parts. Check the signal line between pin (4) of connector AA and pin (81) of IC2201, and pin (6) of T6601.
49
13VT-N200
13VT-N200
Is there a signal at pin (74) of IC2201? YES NO Check BIAS CTL (H) line. Is there "L" level at pin (70) of IC2201?
NO
NO Replace defective parts. YES Clean A/C head. NO Readjust azimuth and height. YES Replace A/C head. NO NO Are azimuth and height of the A/C head properly adjusted?
YES Are the FFC MH-AA and the PB AMP's peripheral parts around pins (75)~(78) of IC2201 normal?
50
Is there "L" level at pin (72) of IC2201? YES Is there a signal at pin (85) of IC2201? YES NO
Replace IC2201.
Check line between pin (85) of IC2201 and pin (1) of IC402.
NO
YES Is 120V AC applied to line between K701 and K702? NO AC cord broken. Normal YES Abnormal Pin (7) of T701 voltage check about: 170V DC at 120V AC
IC701, Check
YES Does pulse waveform NO exist at line between pin (1) and (2) of IC701? Check IC701 and adjacent parts. Abnormal YES IC701, D727 Normal
Normal
TROUBLESHOOTING OF TV SECTION
51
Normal Q601, Q602 and R603
Abnomal
Normal
IC401 (iX3253CE)
C880
13VT-N200
13VT-N200
Circuit to be checked: 1. TUNER 2. PIF 3. Automatic gain control 4. 9V power source FLOW CHART NO.2-3 NO VERTICAL SCAN FLOW CHART NO.2-4 Vertical freq check Abnormal
NO PICTURE, NO SOUND
Does the noise level increase at max, Contrast, Brightness, and Sound Control?
Picture noise decrease but sound level varies greatly. YES Is there a signal at NO pin (53) of IC401. Normal NO IC501 (LA7830) bias check. Abnormal Pin (22) of IC401 bias check. Abnormal
CF631 (503kHz)
YES
Check the IC401 and adjacent parts Is there a signal at pin (54) of IC401? YES Normal
IC401
Is there a signal at pin NO Check the Q404 (43) of IC401? and adjacent parts. YES
Is there a Check signal at the pin (2) of NO IC401 IC351 and (AN adjacent 7511)? parts.
52
YES Check the speaker. Abnormal Check IC2001. Does the 9V (+B) appear at pin (48) of IC401? Normal Abnormal Check IC401. Check the PC9V line.
Is there a signal at pins NO Check the (6) and IC351. (8) of IC351? Check the IC401, and adjacent parts.
Normal
Normal
Abnormal
Check IC401.
YES NO Does waveform appear at pin (54) of IC401? Is there a signal at pin (55) of IC401? NO YES NO Check IC401 and adjacent parts. Check the TV: TROUBLESHOOTING "NO SOUND".
INFRARED R/C TROUBLESHOOTING FLOW CHART NO.2-6 No operation is possible from the infrared remote control.
NO PLAYBACK PICTURE
Is there a signal at pin (39) of IC401? NO Check the VCR: TROUBLESHOOTING "NO PLAYBACK".
NO
53
YES Is 5V applied at pin (2) of the remote control receiver? Is "L" pulse given out of pin (1) of the receiver and received at pin (14) of IC2001, when the infrared remote control is activated? YES Is fluorescent lighting enough away from the set?
NO
NO
Reposition the set not to be exposed to strong light. NO YES Check IC2001.
13VT-N200
13VT-N200
CHASSIS LAYOUT
H
PWB-B
F
PWB-D
PWB-C PWB-A
1 2 3 4 5 6 7 8 9 10 11 12
54
55
13VT-N200
10
11
12
56
57
13VT-N200
10
11
12
58
59
13VT-N200
10
11
12
60
61
13VT-N200
2 3
64
10
62
13VT-N200
10
11 1
12
13
14 3
15
16
17 5
18
6 19
63
13VT-N200
10
11
12
64
65
13VT-N200
10
11
12
66
67
13VT-N200
10
11
12
68
69
13VT-N200
NOTE:
1. The unit of resistance "ohm" is omitted (K:1000 ohms, M:1 Meg ohm). 2. All resistors are 1/8 watt, unless otherwise noted. 3. All capacitors are 50V, unless otherwise noted. 4. All capacitors are F, unless otherwise noted. (P: F) 5. (G) indicates 2% tolerance may be used.
CONDI-
1. Photographs taken on a standard gated color bar signal, the tint setting adjusted for proper color. The wave shapes at the red, green and blue cathodes of the picture tube depend on the tint, color level and picture control. 2. indicates waveform check points (See chart, waveforms are measured from point indicated to chassis ground.)
AND SHADED ( ) COMPONENTS = SAFETY RELATED PARTS. MARK= X-RAY RELATED PARTS.
DRGANNES MARQUES ET HACHRES ( ): PIECES RELATIVES A LA SECURITE. MARQUE : PIECS RELATIVE AUX RAYONS X. This circuit diagram is a standard one, printed circuits may be subject to change for product improvement without prior notice.
WAVEFORMS
D
10
70
13VT-N200
10
11 1
12
13
14 3
15
16
17 5
18
6 19
71
13VT-N200
10
11
12
72
73
13VT-N200
10
11
12
74
75
13VT-N200
10
11
12
76
77
13VT-N200
10
11
12
78
79
13VT-N200
10
11
12
80
81
13VT-N200
82
13VT-N200
83
13VT-N200
84
13VT-N200
85
13VT-N200
Ref. No. Part No. 5 Description Code Ref. No. Part No. 5 Description Code
PARTS LIST
PARTS REPLACEMENT
Replacement parts which have these special safety characteristics identified in this manual ; electrical components having such features are identified by and shaded areas in the Replacement Parts Lists and Schematic Diagrams. The use of a substitute replacement part which dose no have the same safety characteristic as the factory recommended replacement parts shown in this service manual may create shock, fire or other hazards.
Les pi`eces de rechange qui pr lelesentent ces caract leristiques sp leciales de s lecurit le, sont identifi lees dans ce manuel : les pi`eces lelectriques qui pr lesentent ces particularit les, sont rep ler lee par la marque et sont hachur lees dans les listes de pi`eces et dans les diagrammes sch lematiques. La substitution d'une pi`ece de rechange par une autre qui ne pr Lesente pas les m oemes caract Leristiques de s lecurit le que la pi`ece recommand lee parl'usine et dans ce manuel de service, peut provoquer une Lelectrocution, un incendie ou toutautre sinistre.
Contact your nearest SHARP Parts Distributor to order. For location of SHARP Parts Distributor, Please call Toll-Free; 1-800-BE-SHARP 5 MARK: SPARE PARTS-DELIVERY SECTION
'
Ref. No.
Part No.
Ref. No.
PICTURE TUBE
PWB-A: DUNTKA037WEV2
MAIN Unit
BZ BA AK AG
TUNER
NOTE: THE PARTS HERES SHOWN ARE SUPPLIED AS AN ASSEMBLY NOT INDEPENEDENTLY. TU51 VTUATEDH9005C J Tuner BB
INTEGRATAD CIRCUITS
IC351 IC401 IC402 IC501 IC2001 IC2002 IC2003 IC2201 IC3301 IC6601 IC7701 VHiAN7511//-1 RH-iX3253CEZZ VHiM52055FP-1 VHiLA7830//-1 or VHiTA8403K/-1 RH-iX3302CEZZ VHiPST994C/-1 VHiBR2416E2-1 VHiNN3472F/-1 VHiAN3364S/-1 VHiBA7755A/-1 VHiBA6209//1E J J J J R J R J J J J AN7511 TA1268AN M52055FP LA7830 M37760MCA PST994C BR24C16F NN3472FAS AN3364SB BA7755A BA6209-V3 AK AV AH AH BB AD AK AX AL AE AG
TRANSISTORS
Q201 Q301 Q302 Q401 Q402 Q403 Q404 Q428 Q601 Q602 Q670 Q2001 Q2002 Q2003 Q2070 Q2206 Q2207 Q2208 Q2209 Q2210 VS2SC1906//1E VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E VS2SA812-M51E VS2SC1623L51E VS2SA812-M51E VS2SC1623L51E VS2SC2482//-1 VS2SD2586//1E VS2SC1623L51E VS2SC1623L51E VS2SA1271-Y-1 VSUN2212///-1 VSUN2212///-1 VS2SA812-M51E VS2SA812-M51E VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E J J J J J J J J J J J J J J J J J J J J 2SC1906 2SC1623L5 2SC1623L5 2SC1623L5 2SA812-M5 2SC1623L5 2SA812-M5 2SC1623L5 2SC2482 2SD2586 2SC1623L5 2SC1623L5 2SA1271(Y) UN2212 UN2212 2SA812-M5 2SA812-M5 2SC1623L5 2SC1623L5 2SC1623L5 AC AB AB AB AC AB AC AB AD AM AB AB AB AA AA AC AC AB AB AB
86
13VT-N200
Ref. No. Part No. 5 Description Code Ref. No. L53 L201 L202 L203 L211 L301 L302 L303 L401 L402 L403 L404 L408 L615 Part No. 5 J J J J J J J J J J J J J J Description Coil Peaking 1.2H IF Coil Peaking 0.56H Peaking 56H Peaking 8.2H IF Coil Peaking 22H Peaking 12H Peaking 2.7H Peaking 6.8H Peaking 8.2H Peaking 100H Coil Code AE AB AE AB AB AB AD AB AB AB AB AB AB AE
PWB-A: DUNTKA037WEV2
MAIN Unit (Continued)
Q2215 Q2217 Q2218 Q2219 Q2220 Q2233 Q5503 Q6603 Q6604 Q6605 Q6606 Q6607 Q6608 Q6610 Q7703 Q7704 Q7707 Q7708 Q8301 Q8302 Q8303 Q8304 Q8305 VS2SC1623L51E VS2SC1623L51E VSUN2113///-1 VSUN2213///-1 VS2SA812-M51E VSUN2213///-1 VSUN2213///-1 VS2C3939SQR-1 VS2SC2001LK-1 VSUN2113///-1 VSUN2212///-1 VSUN2113///-1 VS2SC1623L51E VSUN2213///-1 RH-PX0233GEZZ RH-PX0233GEZZ VS2SC1623L51E VS2SB1117KU1E VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E J J J J J J J J J J J J J J J J J J J J J J J 2SC1623L5 2SC1623L5 UN2113 UN2213 2SA812-M5 UN2213 UN2213 2SC3939SQR 2SC2001LK UN2113 UN2212 UN2113 2SC1623L5 UN2213 PT493Fl2 PT493Fl2 2SC1623L5 2SB1117KU 2SC1623L5 2SC1623L5 2SC1623L5 2SC1623L5 2SC1623L5 AB AB AA AA AC AA AA AC AA AA AA AA AB AA AD AD AB AE AB AB AB AB AB
DIODES
D51 D52 D53 D401 D402 D451 D455 D501 D502 D651 D652 D653 D656 D670 D710 D2001 D2003 D2007 D2008 D2010 D2201 D2202 D7701 D7702 D7703 D7704 D7705 D7712 D7713 D8301 D8302 D8303 D8304 VA701 RH-EX0619GEZZ RH-EX0207CEZZ RH-EX0631GEZZ RH-DX0475CEZZ RH-EX0603GEZZ RH-EX0616GEZZ RH-DX0475CEZZ RH-DX0441CEZZ RH-DX0131CEZZ VHD1SS82///1A RH-DX0475CEZZ RH-EX0628GEZZ RH-EX0631GEZZ RH-DX0475CEZZ RH-DX0131CEZZ RH-EX0631GEZZ RH-DX0475CEZZ RH-DX0475CEZZ RH-DX0475CEZZ RH-DX0475CEZZ RH-DX0475CEZZ RH-DX0475CEZZ RH-PX0270GEZZ RH-PX0252GEZZ RH-PX0252GEZZ RH-PX0253GEZZ RH-PX0253GEZZ VHD1A3-F///-1 RH-EX0619GEZZ RH-PX0423CEZZ RH-PX0013PEZZ RH-PX0013PEZZ RH-PX0013PEZZ RH-VX0026CEZZ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J R R R J Zener Diode, 6.2V Zener Diode, 30V Zener Diode, 9.1V Diode Zener Diode, 3.8V Zener Diode, 5.6V Diode Diode Diode Diode Diode Zener Diode, 8.2V Zener Diode, 9.1V Diode Diode Zener Diode Diode Diode Diode Diode Diode Diode LED, Cassette GP1S563, TU Reel Sensor GP1S563, SUP Reel Sensor GP1S94, CAM SW B GP1S94, CAM SW A Diode Zener Diode, 6.2V LED, POWER LED, TIMER LED, REC LED, TAMPER PROOF Varistor AA AA AA AB AA AA AB AC AC AC AB AC AA AB AC AA AB AB AB AB AB AB AC AF AF AF AF AA AA AD AC AC AC AC
RCiLP0312CEZZ VP-XF1R2K0000 RCiLi0618CEZZ VP-XFR56K0000 VP-XF560K0000 VP-XF8R2K0000 RCiLi0617CEZZ VP-XF220K0000 VP-XF120K0000 VP-XF2R7K0000 VP-XF6R8K0000 VP-XF8R2K0000 VP-CF101K0000 RCiLP0223CEZZ or RCiLP0288CEZZ or RCiLP0270CEZZ L701 RCiLF0069PEZZ L2001 VP-XF1R0K0000 L2040 RCiLB0015PEZZ L2202 VP-DF4R7K0000 L2203 VP-XF330K0000 L2205 VP-XF101K0000 L2206 VP-ZK471K0000 L2207 VP-ZK561K0000 L2210 VP-XF221K0000 L2213 VP-MK470J0000 L2214 VP-XF221K0000 L2223 RCiLP0312CEZZ L3301 VP-MK101K0000 L5501 VP-MK101K0000 L6601 VPADK153J0000 L6604 VP-DF221K0000 L6607 VP-DF180K0000 L6610 VPADK153J0000 SF201 RFiLC0405CEZZ
R J R J J J J J J J J J J J J J J J J
Coil Peaking 1H Oscillation Coil Peaking 4.7H Peaking 33H Peaking 100H Peaking 470H Peaking 560H Peaking 220H Peaking 47H Peaking 220H Coil Peaking 100H Peaking 100H Peaking 15mH Peaking 220H Peaking 18H Peaking 15mH SAW Filter
AG AB AF AB AB AB AB AB AB AB AB AE AB AB AC AB AB AC AH
TRANSFORMERS
T601 T602
T6601
RTRNZ0144PEZZ R Transformer RTRNF0152PEZZ R H-Volt Transformer or RTRNF0141PEZZ or RTRNF0155PEZZ or RTRNF0192PEZZ RTRNH0053GEZZ J Osc. Transformer
AE BA
AE
CAPACITORS
[EL. Electrolytic, M-Poly. Metalized Polypro Film] C51 VCEA0A1CW476M J 47 16V EL. C52 VCKYCY1HF103Z J 0.01 50V Ceramic C53 VCEA0A1HW105M J 1.0 50V EL. C54 VCEA0A1HW225M J 2.2 50V EL. C55 VCEA0A1CW477M J 470 16V EL. C57 VCEA0A0JW107M J 100 6.3V EL. C201 VCKYCY1EB103K J 0.01 25V Ceramic C202 VCKYCY1EB103K J 0.01 25V Ceramic C203 VCKYCY1EB103K J 0.01 25V Ceramic C204 VCKYCY1CB104K J 0.1 16V Ceramic C205 VCEA0A1HW474M J 0.47 50V EL. C206 VCEA0A1CW477M J 470 16V EL. C207 VCKYCY1HF103Z J 0.01 50V Ceramic C208 VCEA0A1HW474M J 0.47 50V EL. C209 VCKYCY1HB102K J 1000p 50V Ceramic C210 VCKYCY1CB104K J 0.1 16V Ceramic C211 VCCCCY1HH270J J 27p 50V Ceramic C241 VCEA0A1CW477M J 470 16V EL. C301 VCCCCY1HH470J J 47p 50V Ceramic C302 VCCCCY1HH151J J 150p 50V Ceramic C303 VCCCCY1HH560J J 56p 50V Ceramic C305 VCEA0A1HW105M J 1.0 50V EL. C306 VCCCCY1HH470J J 47p 50V Ceramic C307 VCCCCY1HH101J J 100p 50V Ceramic
AB AA AB AB AC AB AA AA AA AB AB AC AA AB AA AB AA AC AA AA AA AB AA AA
PACKAGED CIRCUITS
X801 RCRSB0205CEZZ J Crystal X5502 RCRSB0204GEZZ J Crystal X7701 RCRSB0282CEZZ J Crystal AF AG AG
87
13VT-N200
Ref. No. Part No. 5 Description Code Ref. No.
Part No.
5 33 33 33 33 22 0.022 0.47 0.01 0.01 0.01 0.01 2.0p 10p 2200p 0.1 0.1 0.1 100 1.0 220p 1000p 56p 1.0 0.01 47 100 0.022 1000p 0.1 8200p 2.2 22 0.01 10 2.2 0.01 47 47 0.01 0.1 0.1 4.7 10 220p 0.47 0.47 0.1 33p 0.1 0.1 100 100 68p 220p 68p 47 0.01 0.01 0.1 0.01 0.47 0.022 0.1 47 0.01 0.01 0.01 0.01 0.01 0.01 0.1 27p 0.1
Description 200V EL. 180V EL. 160V EL. 160V 100V 25V 50V 25V 25V 25V 50V 50V 50V 50V 16V 16V 16V 6.3V 50V 50V 50V 50V 10V 50V 10V 6.3V 25V 50V 16V 25V 50V 6.3V 50V 16V 50V 50V 6.3V 6.3V 50V 16V 16V 50V 16V 50V 16V 50V 16V 50V 16V 16V 6.3V 6.3V 50V 50V 50V 6.3V 50V 50V 16V 50V 16V 50V 16V 6.3V 50V 25V 25V 25V 50V 50V 16V 50V 25V EL. EL. Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. EL. Ceramic Ceramic Ceramic Ceramic Ceramic EL. EL. Ceramic Ceramic Ceramic Ceramic EL. EL. Ceramic EL. EL.(N.P) Ceramic EL. EL. Ceramic Ceramic Ceramic EL. EL. Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic EL. EL. Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic
Code AF
PWB-A: DUNTKA037WEV2
MAIN Unit (Continued)
C308 C309 C310 C311 C313 C314 C340 C341 C351 C354 C356 C357 C360 C361 C401 C402 C403 C405 C406 C408 C409 C410 C411 C412 C413 C414 C418 C419 C420 C422 C423 C428 C429 C451 C454 C502 C504 C505 C507 C508 C509 C510 C513 C514 C551 C552 C553 C555 C602 C603 C606 C607 C612 C631 C632 C633 C652 C653 C670 C701 VCKYCY1EB103K J VCEA0A1CW107M J VCKYCY1CB223K J VCEA0A1CW107M J VCKYCY1HB682K J VCKYCY1CB104K J VCKYCY1CB104K J VCE9GA1HW105M J VCKYCY1HB272K J VCEA0A1HW105M J VCEA0A1HW105M J VCKYCY1CF474Z J VCKYCY1HF103Z J VCEA0A1CW477M J VCCCCY1HH271J J VCCCCY1HH470J J VCCCCY1HH100D J VCEA0A1HW105M J VCEA0A1HW474M J VCEA0A1CW106M J VCEA0A1HW105M J VCQYTA1HM104K J VCEA0A1CW108M J VCKYCY1CB104K J VCKYCY1HF103Z J VCE9GA1HW105M J VCKYCY1HF103Z J VCEA0A1CW476M J VCE9GA1HW105M J VCEAKM1CW106MJ VCEA0A1CW106M J VCEA9A1CW476M J VCEA9A1CW106M J VCQYTA2AA563K J VCEA0A1CW106M J VCEA0A1VW477M J VCKYPA2HB561K J VCQYTA1HM473K J VCQYTA1HM152K J VCEA0A1HW107M J VCKYPA2HB102K J VCEA0A1VW477M J VCEA0A1HW225M J VCEACA1HC335J J VCEACA1HC225J J VCEA0A1HW225M J VCCCCY1HH391J J VCE9GA1HW105M J VCKYPA1HB102K J VCKYPA2HB102K J VCKYPA1HB472K J VCFPPD3CA682H J VCFPVC2DB474J J VCEA0A1HW475M J VCKYCY1EB103K J VCEA0A1CW477M J VCEA0A1HW106M J VCEA0A1CW106M J VCKYCY1EB183K J RC-FZ012SGEZZ J or RC-FZ017SCEZZ or RC-FZ012SGEZZ or RC-FZ032CYMZZ or RC-FZ004SCEZZ or RC-FZ029SCEZZ 0.01 100 0.022 100 6800p 0.1 0.1 1.0 2700p 1.0 1.0 0.47 0.01 470 270p 47p 10p 1.0 0.47 10 1.0 0.1 1000 0.1 0.01 1.0 0.01 47 1.0 10 10 47 10 0.056 10 470 560p 0.047 1500p 100 1000p 470 2.2 3.3 2.2 2.2 390p 1.0 1000p 1000p 4700p 6800p 0.47 4.7 0.01 470 10 10 0.018 0.22 25V 16V 16V 16V 50V 16V 16V 50V 50V 50V 50V 16V 50V 16V 50V 50V 50V 50V 50V 16V 50V 50V 16V 16V 50V 50V 50V 16V 50V 16V 16V 16V 16V 100V 16V 35V 500V 50V 50V 50V 500V 35V 50V 50V 50V 50V 50V 50V 50V 500V 50V 1.6kV 200V 50V 25V 16V 50V 16V 25V 275V Ceramic EL. Ceramic EL. Ceramic Ceramic Ceramic EL.(N.P) Ceramic EL. EL. Ceramic Ceramic EL. Ceramic Ceramic Ceramic EL. EL. EL. EL. Mylar EL. Ceramic Ceramic EL.(N.P) Ceramic EL. EL.(N.P) EL. EL. EL. EL. Mylar EL. EL. Ceramic Mylar Mylar EL. Ceramic EL. EL. EL. EL. EL. Ceramic EL.(N.P) Ceramic Ceramic Ceramic M-Poly. M-Poly. EL. Ceramic EL. EL. EL. Ceramic Mylar AA AC AB AC AA AB AB AB AA AB AB AB AA AC AA AA AA AB AB AB AB AC AD AB AA AB AA AB AB AB AB AB AB AB AB AB AA AB AB AB AA AB AB AC AC AB AA AB AA AA AA AE AE AB AA AC AB AB AA AE
C713
C767 C801 C802 C804 C805 C806 C807 C809 C810 C2003 C2006 C2007 C2008 C2009 C2012 C2013 C2014 C2015 C2016 C2018 C2025 C2027 C2031 C2033 C2034 C2201 C2202 C2203 C2204 C2205 C2206 C2207 C2208 C2209 C2210 C2211 C2212 C2213 C2214 C2215 C2216 C2217 C2218 C2219 C2220 C2221 C2222 C2223 C2225 C2226 C2228 C2229 C2230 C2231 C2233 C2238 C2239 C2244 C2245 C2247 C2254 C2258 C2259 C2260 C2267 C2269 C2270 C2271 C2273
RC-EZ0587CEZZ J or RC-EZ0580CEZZ or RC-EZ0585CEZZ or RC-EZ0586CEZZ VCEA0A2AW226M J VCKYCY1EB223K J VCEA0A1HW474M J VCKYCY1EB103K J VCKYCY1EB103K J VCKYCY1EB103K J VCKYPA1HF103Z J VCCCCY1HH2R0C J VCCCCY1HH100D J VCKYCY1HB222K J VCKYCY1CB104K J VCKYCY1CB104K J VCKYCY1CB104K J VCEAKA0JW107M J VCEAKA1HW105M J VCKYCY1HB221K J VCKYCY1HB102K J VCCCCY1HH560J J VCKYCY1AF105Z J VCKYCY1HF103Z J VCEA9A1AW476M J VCEA9A0JW107M J VCKYCY1EB223K J VCKYCY1HB102K J VCKYCY1CB104K J VCKYCY1EB822K J VCEAKM1HW225MJ VCEAKM0JW226M J VCKYCY1HF103Z J VCEA9A1CW106M J VCE9EA1HW225M J VCKYCY1HF103Z J VCEAKM0JW476M J VCEA9A0JW476M J VCKYCY1HF103Z J VCKYCY1CB104K J VCKYCY1CB104K J VCEA9A1HW475M J VCEA9A1CW106M J VCCCCY1HH221J J VCKYCY1CF474Z J VCEA9A1HW474M J VCKYCY1CB104K J VCCCCY1HH330J J VCKYCY1CB104K J VCKYCY1CB104K J VCEA9M0JW107M J VCEAKA0JW107M J VCCCCY1HH680J J VCCCCY1HH221J J VCCCCY1HH680J J VCEA9A0JW476M J VCKYCY1HF103Z J VCKYCY1HF103Z J VCKYCY1CB104K J VCKYCY1HF103Z J VCKYCY1CF474Z J VCKYCY1HF223Z J VCKYCY1CB104K J VCEAKM0JW476M J VCKYCY1HF103Z J VCKYCY1EB103K J VCKYCY1EB103K J VCKYCY1EB103K J VCKYCY1HF103Z J VCKYCY1HF103Z J VCKYCY1CB104K J VCCCCY1HH270J J RC-KZ0019GEZZ J
AC AA AB AA AA AA AA AA AA AA AB AB AB AB AB AA AA AA AC AA AB AB AA AA AB AA AB AB AA AB AB AA AB AB AA AB AB AB AB AA AB AB AB AA AB AB AB AB AA AA AA AB AA AA AB AA AB AB AB AB AA AA AA AA AA AA AB AA AA
88
13VT-N200
Ref. No. Part No. 5 Description Code Ref. No. C7716 C7717 C7719 C7720 C7721 C7722 C7723 C7725 C7726 C7727 C7728 C7729 C7730 C7733 C7735 C7736 C7738 C7739 C7740 C7742 C7744 C7745 C7746 C7747 C7748 C7749 C7750 C7751 C7753 Part No. 5 0.01 10 0.1 0.01 1000p 1000p 1000p 1000p 0.01 0.1 0.01 22 2200p 220p 0.01 0.01 47 0.1 1.0 0.1 100 0.47 0.33 0.1 0.1 0.1 0.1 47 47 Description 50V 16V 16V 50V 50V 50V 50V 50V 25V 16V 50V 16V 50V 50V 50V 50V 16V 16V 50V 16V 16V 50V 50V 16V 16V 16V 16V 6.3V 6.3V Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic EL. Ceramic EL.(N.P) Ceramic EL. Mylar Mylar Ceramic Ceramic Ceramic Ceramic EL. EL. Code AA AB AB AA AA AA AA AA AA AB AA AB AA AA AA AA AB AB AC AB AB AC AB AB AB AB AB AB AB
PWB-A: DUNTKA037WEV2
MAIN Unit (Continued)
C2274 C2275 C2276 C2277 C2278 C3301 C3302 C3303 C3304 C3305 C3306 C3307 C3308 C3311 C3312 C3313 C3314 C3315 C3316 C3317 C5501 C5502 C5503 C5505 C5506 C5507 C5508 C5509 C5510 C5511 C5512 C5513 C5514 C5515 C6601 C6602 C6604 C6605 C6606 C6610 C6611 C6612 C6613 C6614 C6615 C6616 C6617 C6618 C6619 C6630 C6631 C6632 C6633 C6634 C6636 C6638 C6639 C6643 C6645 C7701 C7702 C7703 C7704 C7706 C7707 C7709 C7710 C7711 C7712 C7713 C7714 C7715 VCCCCY1HH560J J VCCCCY1HH820J J VCKYCY1CB104K J VCEA9A1HW105M J VCEA9A1HW105M J VCKYCY1HF223Z J VCCCCY1HH220J J VCKYCY1HF223Z J VCCCCY1HH220J J VCKYCY1HF223Z J VCCCCY1HH220J J VCKYCY1HF223Z J VCCCCY1HH220J J VCKYCY1HB471K J VCKYCY1HF103Z J VCKYCY1CB104K J VCKYCY1CB104K J VCKYCY1HF103Z J VCKYCY1CB104K J VCEAKM0JW476M J VCKYCY1HB392K J VCEA9A1HW105M J VCEA9A1HW225M J VCKYCY1HF103Z J VCKYCY1HF103Z J VCKYCY1CF474Z J VCKYCY1CB104K J VCEA0A0JW477M J VCKYCY1HF103Z J VCKYCY1HF103Z J VCKYCY1CB104K J VCKYCY1HF103Z J VCKYCY1CB104K J VCKYCY1CF474Z J VCKYCY1CB104K J VCEA9A1CW226M J VCKYCY1EB123K J VCKYCY1HB182K J VCKYCY1HB102K J VCKYCY1HF103Z J VCKYCY1HF223Z J VCKYCY1HF103Z J VCEAKA0JW476M J VCEAKM1CW226MJ VCEA9A0JW476M J VCKYCY1CB104K J VCKYCY1CB104K J VCEA9A1CW106M J VCKYCY1CB104K J VCQPSA2AA562J J VCEA9A1CW476M J VCKYCY1HF103Z J VCKYCY1HF103Z J VCEA9A1CW106M J VCEA9A1CW476M J VCEA9M1HW105M J VCEA9A1HW105M J VCEA9A1HW105M J VCKYCY1EB183K J VCKYCY1HF103Z J VCKYCY1HB102K J VCKYCY1HB102K J VCKYCY1HB102K J VCCCCY1HH560J J VCCCCY1HH150J J VCKYCY1HB102K J VCKYCY1HF103Z J VCKYCY1HB272K J VCKYCY1HF103Z J VCEA9A1CW106M J VCKYCY1HF103Z J VCKYCY1HF103Z J 56p 82p 0.1 1.0 1.0 0.022 22p 0.022 22p 0.022 22p 0.022 22p 470p 0.01 0.1 0.1 0.01 0.1 47 3900p 1.0 2.2 0.01 0.01 0.47 0.1 470 0.01 0.01 0.1 0.01 0.1 0.47 0.1 22 0.012 1800p 1000p 0.01 0.022 0.01 47 22 47 0.1 0.1 10 0.1 5600p 47 0.01 0.01 10 47 1.0 1.0 1.0 0.018 0.01 1000p 1000p 1000p 56p 15p 1000p 0.01 2700p 0.01 10 0.01 0.01 50V 50V 16V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 16V 16V 50V 16V 6.3V 50V 50V 50V 50V 50V 16V 16V 6.3V 50V 50V 16V 50V 16V 16V 16V 16V 25V 50V 50V 50V 50V 50V 6.3V 16V 6.3V 16V 16V 16V 16V 100V 16V 50V 50V 16V 16V 50V 50V 50V 25V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 16V 50V 50V Ceramic Ceramic Ceramic EL. EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic EL. EL. Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. EL. EL. Ceramic Ceramic EL. Ceramic Mylar EL. Ceramic Ceramic EL. EL. EL. EL. EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic AA AA AB AB AB AB AA AB AA AB AA AB AA AA AA AB AB AA AB AB AA AB AB AA AA AB AB AC AA AA AB AA AB AB AB AB AA AA AA AA AB AA AB AB AB AB AB AB AB AC AB AA AA AB AB AB AB AB AA AA AA AA AA AA AA AA AA AA AA AB AA AA
VCKYCY1HF103Z J VCEA9A1CW106M J VCKYCY1CB104K J VCKYCY1HF103Z J VCKYCY1HB102K J VCKYCY1HB102K J VCKYCY1HB102K J VCKYCY1HB102K J VCKYCY1EB103K J VCKYCY1CB104K J VCKYCY1HF103Z J VCEA9A1CW226M J VCKYCY1HB222K J VCCCCY1HH221J J VCKYCY1HF103Z J VCKYCY1HF103Z J VCEA9A1CW476M J VCKYCY1CB104K J VCE9EA1HW105M J VCKYCY1CB104K J VCEA9M1CW107M J VCFYFA1HA474J J VCFYFA1HA334J J VCKYCY1CB104K J VCKYCY1CB104K J VCKYCY1CB104K J VCKYCY1CB104K J VCEAKA0JW476M J VCEA9A0JW476M J
RESISTORS
RJ1 RJ2 RJ3 RJ6 RJ7 RJ8 RJ9 RJ10 RJ11 RJ12 RJ13 RJ14 RJ15 RJ16 RJ17 RJ18 RJ19 RJ22 RJ23 RJ25 RJ26 RJ27 RJ28 RJ29 RJ30 RJ31 RJ36 RJ38 RJ39 RJ40 RJ41 R54 R55 R56 R57 R201 R202 R203 R204 R205 R206 R207 R208
[M-Ox. Metal Oxide, M-Film Metal Film] VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL101J J 100 1/10W M-Film VRN-MD2AL101J J 100 1/10W M-Film VRS-CY1JF823J J 82k 1/16W M-Ox. VRN-MD2AL103J J 10k 1/10W M-Film VRN-MD2AL151J J 150 1/10W M-Film VRN-MD2AL122J J 1.2k 1/10W M-Film VRN-MD2AL562J J 5.6k 1/10W M-Film VRN-MD2AL270J J 27 1/10W M-Film VRN-MD2AL331J J 330 1/10W M-Film VRD-RA2EE560J J 56 1/4W Carbon VRN-MD2AL391J J 390 1/10W M-Film VRN-MD2AL331J J 330 1/10W M-Film
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
89
13VT-N200
Ref. No. Part No. 5 Description Code Ref. No. R554 R555 R601 R602 R603 R608 R611 R615 R631 R632 R633 R651 R653 R654 R655 R656 R670 R671 R672 R702 R718 R801 R802 R803 R804 R805 R806 R808 R809 R810 R961 R962 R2001 R2002 R2004 R2005 R2006 R2008 R2009 R2014 R2018 R2020 R2021 R2022 R2023 R2024 R2025 R2026 R2027 R2028 R2029 R2031 R2035 R2036 R2038 R2039 R2040 R2043 R2045 R2047 R2048 R2050 R2053 R2054 R2055 R2063 R2064 R2065 R2066 R2068 R2069 R2070 R2071 R2072 R2073 R2074 Part No. VRN-MD2AL393J VRN-MD2AL103J VRN-MD2AL331J VRD-RM2HD392J VRS-KT3LB222J VRD-RA2BE331J VRD-RA2EE220J VRS-VV3AB271J VRN-MD2AL391J VRD-RA2BE272J VRN-MD2AL472J VRD-RM2HD680J VRD-RA2BE822G VRD-RA2BE103G VRN-MD2AL104J VRD-RM2HD123J VRN-MD2AL103J VRN-MD2AL332J VRN-MD2AL682J RR-DZ0049CEZZ VRN-GA2EB1R0J VRN-MD2AL103J VRN-MD2AL392J VRS-CY1JF272J VRS-CY1JF272J VRS-CY1JF272J VRN-MD2AL333J VRN-MD2AL000J VRN-MD2AL101J VRN-MD2AL101J VRD-RA2BE101J VRD-RA2BE101J VRD-RA2BE102J VRN-MD2AL102J VRN-MD2AL103J VRD-RA2BE102J VRD-RA2BE102J VRD-RA2BE152J VRN-MD2AL101J VRN-MD2AL223J VRN-MD2AL102J VRN-MD2AL471J VRN-MD2AL105J VRD-RA2BE472J VRN-MD2AL102J VRN-MD2AL681J VRS-CY1JF562J VRS-CY1JF562J VRS-CY1JF562J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL103J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL223J VRN-MD2AL223J VRN-MD2AL470J VRN-MD2AL222J VRN-MD2AL104J VRD-RA2BE4R7J VRN-MD2AL221J VRN-MD2AL223J VRN-MD2AL564J VRN-MD2AL334J VRN-MD2AL102J VRN-MD2AL472J VRN-MD2AL102J VRN-MD2AL683J VRN-MD2AL564J VRN-MD2AL103J VRN-MD2AL103J VRN-MD2AL103J VRN-MD2AL000J VRD-RA2BE681J VRN-MD2AL472J VRN-MD2AL562J 5 J J J J J J J J J J J J J J J J J J J R J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 39k 10k 330 3.9k 2.2k 330 22 270 390 2.7k 4.7k 68 8.2k 10k 100k 12k 10k 3.3k 6.8k 3.9M 1.0 10k 3.9k 2.7k 2.7k 2.7k 33k 0 100 100 100 100 1.0k 1.0k 10k 1.0k 1.0k 1.5k 100 22k 1.0k 470 1.0M 4.7k 1.0k 680 5.6k 5.6k 5.6k 1.0k 1.0k 10k 1.0k 1.0k 22k 22k 47 2.2k 100k 4.7 220 22k 560k 330k 1.0k 4.7k 1.0k 68k 560k 10k 10k 10k 0 680 4.7k 5.6k Description 1/10W 1/10W 1/10W 1/2W 3.0W 1/8W 1/4W 1W 1/10W 1/8W 1/10W 1/2W 1/8W 1/8W 1/10W 1/2W 1/10W 1/10W 1/10W 1/2W 1/4W 1/10W 1/10W 1/16W 1/16W 1/16W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/8W 1/10W 1/10W 1/8W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/16W 1/16W 1/16W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W M-Film M-Film M-Film Carbon M-Ox. Carbon Carbon M-Ox. M-Film Carbon M-Film Carbon Carbon Carbon M-Film Carbon M-Film M-Film M-Film Carbon M-Film M-Film M-Film M-Ox. M-Ox. M-Ox. M-Film M-Film M-Film M-Film Carbon Carbon Carbon M-Film M-Film Carbon Carbon Carbon M-Film M-Film M-Film M-Film M-Film Carbon M-Film M-Film M-Ox. M-Ox. M-Ox. M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film Carbon M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film Carbon M-Film M-Film Code AA AA AA AA AC AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AA AA AA AA AA AA AA AA AA AA AA AA
PWB-A: DUNTKA037WEV2
MAIN Unit (Continued)
R297 R301 R302 R303 R305 R306 R308 R310 R311 R313 R314 R315 R342 R350 R351 R355 R356 R401 R402 R403 R404 R405 R406 R407 R408 R409 R410 R411 R412 R413 R414 R415 R416 R417 R418 R421 R422 R423 R424 R425 R426 R427 R428 R429 R433 R434 R435 R436 R437 R439 R445 R451 R453 R454 R456 R466 R501 R504 R505 R506 R507 R508 R510 R511 R512 R516 R517 R518 R519 R526 R551 R552 VRN-MD2AL000J VRN-MD2AL562J VRN-MD2AL102J VRN-MD2AL123J VRN-MD2AL103J VRN-MD2AL222J VRN-MD2AL271J VRN-MD2AL273J VRN-MD2AL102J VRD-RA2BE471J VRN-MD2AL471J VRN-MD2AL391J VRN-MD2AL273J VRN-MD2AL393J VRN-MD2AL223J VRN-MD2AL473J VRN-MD2AL473J VRN-MD2AL682J VRN-MD2AL331J VRN-MD2AL331J VRN-MD2AL222J VRN-MD2AL330J VRN-MD2AL680J VRN-MD2AL102J VRN-MD2AL471J VRN-MD2AL123J VRS-CY1JF823J VRD-RA2BE104J VRD-RA2EE561J VRN-MD2AL470J VRN-MD2AL470J VRN-MD2AL470J VRN-MD2AL222J VRN-MD2AL122J VRN-MD2AL000J VRN-MD2AL101J VRN-MD2AL102J VRN-MD2AL152J VRN-MD2AL182J VRN-MD2AL182J VRN-MD2AL182J VRD-RA2EE101J VRD-RA2EE101J VRD-RA2EE101J VRN-MD2AL000J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL103J VRN-MD2AL333J VRN-MD2AL472J VRD-RA2BE122J VRS-SV2HC103J VRD-RA2EE474J VRD-RA2EE184J VRN-MD2AL273J VRN-VV3AB1R5J VRN-MD2AL101J VRD-RA2BE471J VRD-RA2BE101J VRD-RA2BE683G VRD-RA2BE104G VRD-RA2BE683J VRN-VV3AB1R0J VRN-GA2EB1R0J VRD-RM2HD561J VRD-RA2BE153G VRD-RA2BE223G VRD-RA2BE154J VRD-RM2HD681J VRN-MD2AL183J VRN-MD2AL472J VRN-MD2AL102J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 0 5.6k 1.0k 12k 10k 2.2k 270 27k 1.0k 470 470 390 27k 39k 22k 47k 47k 6.8k 330 330 2.2k 33 68 1.0k 470 12k 82k 100k 560 47 47 47 2.2k 1.2k 0 100 1.0k 1.5k 1.8k 1.8k 1.8k 100 100 100 0 1.0k 1.0k 10k 33k 4.7k 1.2k 10k 470k 180k 27k 1.5 100 470 100 68k 100k 68k 1.0 1.0 560 15k 22k 150k 680 18k 4.7k 1.0k 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/16W 1/8W 1/4W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/4W 1/4W 1/4W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/2W 1/4W 1/4W 1/10W 1W 1/10W 1/8W 1/8W 1/8W 1/8W 1/8W 1W 1/4W 1/2W 1/8W 1/8W 1/8W 1/2W 1/10W 1/10W 1/10W M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film Carbon M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Ox. Carbon Carbon M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film Carbon Carbon Carbon M-Film M-Film M-Film M-Film M-Film M-Film Carbon M-Ox. Carbon Carbon M-Film M-Film M-Film Carbon Carbon Carbon Carbon Carbon M-Film M-Film Carbon Carbon Carbon Carbon Carbon M-Film M-Film M-Film AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA
90
13VT-N200
Ref. No. Part No. 5 Description Code Ref. No. R6603 R6604 R6605 R6606 R6607 R6610 R6611 R6612 R6613 R6614 R6615 R6616 R6630 R6632 R6633 R6634 R6635 R6636 R6637 R6638 R6639 R6642 R6643 R6661 R6665 R7701 R7702 R7703 R7704 R7705 R7707 R7708 R7709 R7710 R7711 R7713 R7714 R7715 R7716 R7717 R7718 R7719 R7720 R7721 R7722 R7723 R7724 R7725 R7727 R7731 R7732 R7736 R7737 R7738 R7739 R7740 R7741 R7742 R7743 R7744 R7745 R7746 R7747 R7748 R7749 R7750 R7751 R7752 R7753 R7755 R7756 R7757 R7758 R7759 R7760 R7761 Part No. VRN-MD2AL472J VRN-MD2AL334J VRN-MD2AL333J VRN-MD2AL471J VRN-MD2AL223J VRN-MD2AL821J VRN-MD2AL681J VRS-CY1JF225J VRN-MD2AL561J VRN-MD2AL123J VRN-MD2AL223J VRN-MD2AL103J VRN-MD2AL473J VRD-RA2EE4R7J VRN-MD2AL682J VRD-RA2BE470J VRN-MD2AL000J VRN-MD2AL561J VRD-RA2BE153J VRN-MD2AL472J VRN-MD2AL183J VRN-MD2AL472J VRN-MD2AL473J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J VRD-RA2BE102J VRD-RA2BE102J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J VRD-RA2BE102J VRD-RA2BE102J VRN-MD2AL103J VRN-MD2AL103J VRN-MD2AL103J VRN-MD2AL103J VRN-MD2AL103J VRD-RA2BE102J VRD-RA2BE102J VRD-RA2BE102J VRN-MD2AL684J VRN-MD2AL000J VRD-RA2BE102J VRD-RA2BE102J VRN-MD2AL103J VRD-RA2BE102J VRN-MD2AL562J VRN-MD2AL102J VRN-MD2AL562J VRN-MD2AL562J VRD-RA2BE101J VRD-RA2BE101J VRN-MD2AL102J VRN-MD2AL473J VRN-MD2AL224J VRN-MD2AL472J VRN-MD2AL393J VRN-MD2AL153J VRN-MD2AL183J VRN-MD2AL102J VRN-MD2AL104J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J VRD-RA2BE472J VRN-MD2AL681J VRD-RA2BE332J VRD-RA2BE102J 5 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 4.7k 330k 33k 470 22k 820 680 2.2M 560 12k 22k 10k 47k 4.7 6.8k 47 0 560 15k 4.7k 18k 4.7k 47k 0 0 1.0k 1.0k 1.0k 1.0k 1.0k 1.0k 1.0k 1.0k 1.0k 1.0k 1.0k 1.0k 10k 10k 10k 10k 10k 1.0k 1.0k 1.0k 680k 0 1.0k 1.0k 10k 1.0k 5.6k 1.0k 5.6k 5.6k 100 100 1.0k 47k 220k 4.7k 39k 15k 18k 1.0k 100k 1.0k 1.0k 1.0k 1.0k 1.0k 1.0k 4.7k 680 3.3k 1.0k Description 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/16W 1/10W 1/10W 1/10W 1/10W 1/10W 1/4W 1/10W 1/8W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/8W 1/10W 1/10W 1/8W 1/8W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/8W 1/8W M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Ox. M-Film M-Film M-Film M-Film M-Film Carbon M-Film Carbon M-Film M-Film Carbon M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film Carbon Carbon M-Film M-Film M-Film M-Film Carbon Carbon M-Film M-Film M-Film M-Film M-Film Carbon Carbon Carbon M-Film M-Film Carbon Carbon M-Film Carbon M-Film M-Film M-Film M-Film Carbon Carbon M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film Carbon M-Film Carbon Carbon Code AA AC AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
PWB-A: DUNTKA037WEV2
MAIN Unit (Continued)
R2201 R2202 R2203 R2204 R2205 R2208 R2209 R2210 R2211 R2212 R2213 R2215 R2216 R2217 R2225 R2226 R2227 R2228 R2229 R2230 R2231 R2232 R2233 R2234 R2235 R2236 R2237 R2238 R2245 R2253 R2254 R2255 R2257 R2260 R2261 R2262 R2263 R2267 R2277 R2278 R2279 R2284 R2285 R2294 R3178 R3179 R3180 R3181 R3207 R3208 R3209 R3210 R3211 R3212 R3213 R3214 R3215 R3302 R3308 R3311 R3312 R3314 R3361 R3362 R3365 R3367 R5501 R5502 R5503 R5504 R6601 R6602 VRN-MD2AL103J J 10k VRD-RA2BE103J J 10k VRN-MD2AL474J J 470k VRS-CY1JF125J J 1.2M VRN-MD2AL121J J 120 VRN-MD2AL272J J 2.7k VRN-MD2AL151J J 150 VRN-MD2AL103J J 10k VRN-MD2AL333J J 33k VRN-MD2AL103J J 10k VRN-MD2AL471J J 470 VRN-MD2AL472J J 4.7k VRN-MD2AL103J J 10k VRN-MD2AL103J J 10k VRN-MD2AL561J J 560 VRN-MD2AL272J J 2.7k VRN-MD2AL681J J 680 VRN-MD2AL471J J 470 VRN-MD2AL102J J 1.0k VRD-RA2BE272J J 2.7k VRN-MD2AL104J J 100k VRN-MD2AL101J J 100 VRD-RA2BE822J J 8.2k VRN-MD2AL681J J 680 VRN-MD2AL153J J 15k VRN-MD2AL331J J 330 VRN-MD2AL822J J 8.2k VRN-MD2AL272J J 2.7k VRN-MD2AL681J J 680 VRN-MD2AL122J J 1.2k VRN-MD2AL333J J 33k VRN-MD2AL223J J 22k VRD-RA2BE101J J 100 VRN-MD2AL103J J 10k VRN-MD2AL103J J 10k VRN-MD2AL103J J 10k VRN-MD2AL103J J 10k VRN-MD2AL332J J 3.3k VRD-RA2BE103J J 10k VRD-RA2BE102J J 1.0k VRD-RA2BE102J J 1.0k VRD-RA2BE100J J 10 VRN-MD2AL824J R 820k VRN-MD2AL000J J 0 VRN-MD2AL221J J 220 VRN-MD2AL221J J 220 VRN-MD2AL221J J 220 VRN-MD2AL221J J 220 VRN-MD2AL223J J 22k VRN-MD2AL103J J 10k VRN-MD2AL682J J 6.8k VRN-MD2AL472J J 4.7k VRN-MD2AL563J J 56k VRN-MD2AL223J J 22k VRN-MD2AL103J J 10k VRN-MD2AL682J J 6.8k VRN-MD2AL472J J 4.7k VRN-MD2AL103J J 10k VRN-MD2AL102J J 1.0k VRN-MD2AL102J J 1.0k VRN-MD2AL682J J 6.8k VRN-MD2AL473J J 47k VRN-MD2AL000J J 0 VRN-MD2AL000J J 0 VRN-MD2AL000J J 0 VRN-MD2AL000J J 0 VRN-MD2AL122J J 1.2k VRN-MD2AL103J J 10k VRN-MD2AL101J J 100 VRN-MD2AL101J J 100 VRN-MD2AL102J J 1.0k VRN-MD2AL151J J 150 1/10W 1/8W 1/10W 1/16W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W M-Film Carbon M-Film M-Ox. M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film Carbon M-Film M-Film Carbon M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film Carbon M-Film M-Film M-Film M-Film M-Film Carbon Carbon Carbon Carbon M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
91
13VT-N200
Ref. No. Part No. 5 Description Code Ref. No. P3301 P7702 P7706 SC3301 SC6601 SC6602 SC7701 SC7702 Part No. 5 Description Plug, 3-pin (TP3302-4) Plug, 2-pin (TP7703-4) Plug, 8-pin (AC) Socket, 6-pin (AH) Socket, 6-pin (AA) Socket, 2-pin (AE) Socket, 7-pin (AD) Socket, 2-pin (AL) R/C Receiver Heat Sink, for IC501 Heat Sink, for Q602 Shield Shield Connecting Cord Connecting Cord Holder Holder Screw Screw Code AA AA AD AC AB AC AC AC AL AE AE AD AD AE AD AD AD AA AA
PWB-A: DUNTKA037WEV2
MAIN Unit (Continued)
R7762 R7763 R7764 R7765 R7766 R7767 R7768 R7769 R7771 R7774 R7775 R7777 R7778 R7779 R7780 R7781 R7788 R7789 R7790 R7791 R7792 R7793 R7794 R7795 R7797 R7799 R7801 R7808 R7809 R7810 R7811 R8301 R8302 R8303 R8304 R8305 VRN-MD2AL103F VRN-MD2AL103F VRN-MD2AL103J VRD-RA2BE123J VRN-MD2AL123J VRD-RA2EE151J VRD-RA2BE102J VRN-MD2AL103J VRD-RM2HD122J VRG-SC2EB1R2J VRD-RA2BE102J VRN-MD2AL391J VRN-MD2AL473J VRN-MD2AL391J VRN-MD2AL473J VRN-MD2AL223J VRN-MD2AL104J VRD-RA2BE271J VRD-RA2BE104J VRD-RA2BE271J VRG-SC2EB1R8J VRD-RA2BE103J VRD-RA2BE103J VRD-RA2BE102J VRN-MD2AL182J VRN-MD2AL103J VRN-MD2AL102J VRN-MD2AL101J VRN-MD2AL101J VRN-MD2AL331J VRN-MD2AL331J VRD-RA2BE821J VRD-RA2BE471J VRD-RA2BE821J VRD-RA2BE821J VRD-RA2BE821J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 10k 10k 10k 12k 12k 150 1.0k 10k 1.2k 1.2 1.0k 390 47k 390 47k 22k 100k 270 100k 270 1.8 10k 10k 1.0k 1.8k 10k 1.0k 100 100 330 330 820 470 820 820 820 1/10W 1/10W 1/10W 1/8W 1/10W 1/4W 1/8W 1/10W 1/2W 1/4W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/8W 1/4W 1/8W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/8W 1/8W 1/8W M-Film AA M-Film AA M-Film AA Carbon AA M-Film AA Carbon AA Carbon AA M-Film AA Carbon AA Fuse Resistor AB Carbon AA M-Film AA M-Film AA M-Film AA M-Film AA M-Film AA M-Film AA Carbon AA Carbon AA Carbon AA Fuse Resistor AE Carbon AA Carbon AA Carbon AA M-Film AA M-Film AA M-Film AA M-Film AA M-Film AA M-Film AA M-Film AA Carbon AA Carbon AA Carbon AA Carbon AA Carbon AA
QPLGN0352GEZZ J QPLGN0252GEZZ J QPLGZ0883GEZZ J QSOCN0611REN1 R QSOCN0695REZZ R QSOCZ0293GEZZ J QSOCN0795REZZ R QSOCZ0292GEZZ J RMC3101 RRMCU0222CEZZ J RDA501 PRDAR0242PEFW R or PRDAR0146PEFW RDA602 PRDAR0219PEFW R PSLDM0251PEFW R PSLDM0252PEFW R QCNW-2205PEZZ R QCNW-5509PEN3 R LHLDP1057PEZZ R LHLDZ1962AJ00 J LX-BZ3100CEFD J LX-TZ3004CEFD J
SWITCHES
S2001 S2501 S2502 S2503 S2504 S2505 S2506 S2507 S2508 S2509 S2510 S7701 QSW-P0593CEZZ QSW-K0077GEZZ QSW-K0077GEZZ QSW-K0077GEZZ QSW-K0077GEZZ QSW-K0077GEZZ QSW-K0077GEZZ QSW-K0077GEZZ QSW-K0077GEZZ QSW-K0077GEZZ QSW-K0077GEZZ QSW-F0042AJZZ J J J J J J J J J J J J POWER STOP/EJECT PLAY FF REW REC EZ PLAY CH-UP CH-DOWN VOL-UP VOL-DOWN Rec Tip Switch AE AB AB AB AB AB AB AB AB AB AB AG
MISCELLANEOUS PARTS
F701 FB2001 FB7701 FB7702 FB7703 FH701 FH702 P350 P401 P402 P404 P602 P651 P703 P2201
Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Fuse Holder Fuse Holder Plug, 3-pin (OR) Plug, 8-pin (MA) Plug, 10-pin (MB) Plug, 5-pin (GC) Plug, 6-pin (K) Plug, 3-pin (TP651-3) Plug, 5-pin (GR) Plug, 3-pin (TP2201-2,TP6001) P2401 QPLGN0561CEZZ J Plug, 5-pin
QFS-B4023CEZZ or QFS-B4021GEZZ RBLN-0036CEZZ RBLN-0036CEZZ RBLN-0037CEZZ RBLN-0036CEZZ QFSHD1013CEZZ QFSHD1014CEZZ QPLGN0361CEZZ QPLGZ0840CEZZ QPLGZ1040CEZZ QPLGN0578GEZZ QPLGN0660CEZZ QPLGN0361CEZZ QPLGN0561CEZZ QPLGN0361CEZZ
J Fuse 4A 125V J J J J J J J J J J R J J J
AC AB AB AB AB AC AC AB AF AE AB AC AB AB AB AB
92
13VT-N200
Ref. No. Part No. 5 Description Code Ref. No. Part No. 5 Description Code
PWB-B: DUNTKA039WEV0
CRT Unit
TRANSISTORS
Q853 Q854 Q855 Q894 VS2SC2229O/1E VS2SC2229O/1E VS2SC2229O/1E VS2SA1266-Y-1 J J J J 2SC22290 2SC22290 2SC22290 2SA1266(Y) AD AD AD AA
PWB-C: DUNTKA038WEV0
POWER Unit
INTEGRATED CIRCUIT
IC701 IC702 IC703 VHiSTRG6624-1 RH-FX0029CEZZ or RH-FX0018CEZZ RH-FX0029CEZZ or RH-FX0018CEZZ VHiBA005T//-1 VHiPQ09RD11-1 RH-FX0047CEZZ J STRG6624 J PS2501 J PS2501 J BA005T J PQ09RD11 J PC817 AR AE AE AF AG AD
DIODE
D898 RH-DX0475CEZZ J Diode AB IC756 IC765 IC775 Ceramic Ceramic Ceramic Ceramic EL. EL. EL. Ceramic AB AB AB AC AB AB AB AA
CAPACITORS
C851 C852 C853 C880 C892 C893 C894 C895
[EL. Electrolytic] VCCCPA1HH271J J 270p 50V VCCCPA1HH271J J 270p 50V VCCCPA1HH221J J 220p 50V RC-KZ0016CEZZ J 0.01 1.4kV VCEA0A1HW106M J 10 50V VCEA0A1HW106M J 10 50V VCEA0A1CW476M J 47 16V VCKYPA1HF103Z J 0.01 50V
TRANSISTORS
Q735 Q750 Q751 Q752 Q753 Q756 VS2SC3198-Y-1 VSKTA1024-Y-1 VS2SC3198-Y-1 VS2SC2229O/1E VS2SA949Y//2E VS2SD471-KL1E J J J J J J 2SC3198(Y) KTA1024(Y) 2SC3198(Y) 2SC22290 2SA949Y 2SD471-KL AA AD AA AD AC AC
RESISTORS
R849 R850 R854 R855 R856 R857 R859 R861 R863 R876 R877 R878 R880 R881 R882 R891 R892 R894 R895
DIODES
Carbon Carbon Carbon Carbon Carbon Carbon M-Ox. M-Ox. M-Ox. Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA RH-DX0490CEZZ or RH-DX0154CEZZ D702 RH-DX0490CEZZ or RH-DX0154CEZZ D703 RH-DX0490CEZZ or RH-DX0154CEZZ D704 RH-DX0490CEZZ or RH-DX0154CEZZ D705 VHD1SS82///1A or VHD1SS244//-1 D706 VHD10ELS2//-1 D707 VHD1SS82///1A or VHD1SS244 D708 VHSSFOR5D43-1 D709 RH-EX0610GEZZ D711 RH-EX0207CEZZ D725 RH-DX0469CEZZ D726 RH-DX0469CEZZ D727 RH-DX0461CEZZ D735 RH-EX0617GEZZ D738 RH-DX0475CEZZ D739 RH-DX0475CEZZ D740 RH-DX0475CEZZ D741 RH-DX0475CEZZ D742 RH-EX0628GEZZ D743 RH-DX0475CEZZ D745 RH-EX0631GEZZ D746 RH-DX0475CEZZ D747 RH-DX0475CEZZ D748 RH-DX0475CEZZ D749 RH-DX0475CEZZ D775 RH-DX0441CEZZ or RH-DX0279CEZZ or RH-DX0442CEZZ or RH-DX0443CEZZ PR702 RMPTP0026CEZZ D701 J Diode J Diode J Diode J Diode J Diode J Diode J Diode J J J J J J J J J J J J J J J J J J J SFOR5D43 Zener Diode, 4.7V Zener Diode, 30V Diode Diode Diode Zener Diode, 6.2V Diode Diode Diode Diode Zener Diode, 8.2V Diode Zener Diode, 9.1V Diode Diode Diode Diode Diode AC AC AC AC AC AC AC AC AA AA AF AF AG AA AB AB AB AB AC AB AA AB AB AB AB AC
[M-Ox. Metal Oxide] VRD-RA2BE331J J 330 1/8W VRD-RA2BE470J J 47 1/8W VRD-RA2BE331J J 330 1/8W VRD-RA2BE331J J 330 1/8W VRD-RA2BE470J J 47 1/8W VRD-RA2BE470J J 47 1/8W VRS-VV3AB123J J 12k 1W VRS-VV3AB123J J 12k 1W VRS-VV3AB123J J 12k 1W VRD-RA2BE121J J 120 1/8W VRD-RA2BE121J J 120 1/8W VRD-RA2BE121J J 120 1/8W VRD-RM2HD332J J 3.3k 1/2W VRD-RM2HD332J J 3.3k 1/2W VRD-RM2HD332J J 3.3k 1/2W VRD-RA2BE102J J 1.0k 1/8W VRD-RA2BE181J J 180 1/8W VRD-RA2BE221J J 220 1/8W VRD-RA2EE102J J 1.0k 1/4W
MISCELLANEOUS PARTS
P860 QPLGN0561CEZZ J Plug, 5-pin (GR) P880 QPLGN0578GEZZ J Plug, 5-pin (GC) SC882 QSOCV0842CEZZ J CRT Socket, 8-pin or QSOCV0839CEZZ QCNW-2418PEZZ R Connecting Cord (GC) QCNW-5030PEN5 R Connecting Cord (GR) AB AB AH AE AE
J Packaged Circuit
AF
COILS
L725 L726 L727 RCiLP0195CEZZ RCiLP0179CEZZ RCiLP0179CEZZ J Coil 68H J Coil 47H J Coil 47H AD AD AD
93
13VT-N200
Ref. No. Part No. 5 Description Code Ref. No. R709 R710 R711 R713 R714 R715 R716 R717 R719 R727 R730 R731 R733 R734 R735 R736 R737 R739 R740 R741 R742 R745 R746 R747 R748 R749 R750 R751 R752 R753 R754 R755 R756 R757 R758 R760 R761 R762 R766 R774 R775 R776 Part No. VRN-GA2EB1R0J VRD-RM2HD180J VRD-RA2EE122J VRS-SV2HC272J VRD-RA2BE102J VRD-RA2BE153J VRD-RA2EE152J VRD-RM2HD104J VRW-KQ3HC4R7K VRS-VV3DB223J VRD-RA2BE272J VRD-RA2BE332J VRD-RA2BE152J VRD-RA2BE681J VRD-RA2EE681J VRD-RM2HD563J VRD-RA2EE824J VRD-RA2EE681J VRD-RM2HD470J VRN-RA2BK332F VRD-RA2BE102J VRD-RA2BE102J VRD-RA2BE103J VRD-RA2BE681J VRD-RA2EE182J VRD-RA2EE221J VRD-RA2BE102J VRD-RA2BE104J VRD-RM2HD104J VRD-RA2BE223J VRD-RA2BE563J VRD-RA2EE102J VRD-RM2HD221J VRS-VV3LB100J VRD-RA2EE102J VRD-RM2HD223J VRD-RA2EE562J VRD-RM2HD562J VRD-RA2BE102J VRD-RA2BE102J VRD-RM2HD473J VRD-RM2HD473J 5 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 1.0 18 1.2k 2.7k 1.0k 15k 1.5k 100k 4.7 22k 2.7k 3.3k 1.5k 680 680 56k 820k 680 47 3.3k 1.0k 1.0k 10k 680 1.8k 220 1.0k 100k 100k 22k 56k 1.0k 220 10 1.0k 22k 5.6k 5.6k 1.0k 1.0k 47k 47k Description 1/4W 1/2W 1/4W 1/2W 1/8W 1/8W 1/4W 1/2W 5W 2W 1/8W 1/8W 1/8W 1/8W 1/4W 1/2W 1/4W 1/4W 1/2W 1/8W 1/8W 1/8W 1/8W 1/8W 1/4W 1/4W 1/8W 1/8W 1/2W 1/8W 1/8W 1/4W 1/2W 3.0W 1/4W 1/2W 1/4W 1/2W 1/8W 1/8W 1/2W 1/2W M-Film Carbon Carbon M-Ox. Carbon Carbon Carbon Carbon Cement M-Ox. Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon M-Film Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon M-Ox. Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Code AA AA AA AA AA AA AA AA AE AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA
PWB-C: DUNTKA038WEV0
POWER Unit (Continued)
TRANSFORMER
T701
AP
CONTROL
R738
AC
CAPACITORS
[EL. Electrolytic, M-Poly. Metalized Polypro Film] C702 VCKYPB2HE103P J 0.01 500V Ceramic or RC-KZ007JCEZZ or RC-KZ0016CEZZ C703 VCKYPB2HE103P J 0.01 500V Ceramic or RC-KZ007JCEZZ or RC-KZ0016CEZZ C705 RC-EZ0613CEZZ J 470 200V EL. or RC-EZ0514CEZZ or RC-EZ0682CEZZ or RC-EZ0631CEZZ C706 RC-KZ0404CEZZ J 3300p 2kV Ceramic C708 VCCSPA1HL471J J 470p 50V Ceramic C709 VCEA0A1HW107M J 100 50V EL. C710 VCQYTA1HM222J J 2200p 50V Mylar C711 VCFYFA1HA224J J 0.22 50V Mylar C712 RC-KZ0312CEZZ J 4700p 125V Ceramic C722 VCKYPA1HB102K J 1000p 50V Ceramic C723 VCKYPA1HB102K J 1000p 50V Ceramic C724 VCKYPA1HB102K J 1000p 50V Ceramic C725 VCKYPA1HB102K J 1000p 50V Ceramic C726 RC-EZ1088CEZZ J 2200 16V EL. C727 RC-EZ1075CEZZ J 2200 10V EL. C728 RC-KZ0365CEZZ J 1000p 1kV Ceramic C729 RC-KZ0365CEZZ J 1000p 1kV Ceramic C730 RC-EZ0724CEZZ J 100 160V EL. C735 VCCCPA1HH680J J 68p 50V Ceramic C739 VCEA0A1HW104M J 0.1 50V EL. C747 VCEA0A1HW106M J 10 50V EL. C748 VCEA0A1HW107M J 100 50V EL. C755 VCEA0A1EW107M J 100 25V EL. C756 VCEA0A1CW476M J 47 16V EL. C757 VCEA0A0JW107M J 100 6.3V EL. C758 VCEA0A1CW226M J 22 16V EL. C759 VCEA0A1AW476M J 47 10V EL. C768 VCEA0A1CW476M J 47 16V EL. C769 VCEA0A1CW476M J 47 16V EL. C775 VCKYPA1HB103K J 0.01 50V Ceramic
AB
AB
AL
AE AA AB AA AB AD AA AA AA AA AF AF AD AD AG AA AB AB AB AC AB AB AB AB AB AB AA
MISCELLANEOUS PARTS
RY701 RRLYJ0090CEZZ J or RRLYU0036CEZZ or RRLYU0038CEZZ or RRLYJ0082CEZZ or RRLYJ0092CEZZ RY725 RRLYJ0092CEZZ J or RRLYU0038CEZZ FB702 RBLN-0037CEZZ J FB725 RBLN-0054CEZZ J FB726 RBLN-0054CEZZ J FB727 RBLN-0057CEZZ J FB731 RBLN-0057CEZZ J FB732 RBLN-0057CEZZ J P351 QPLGN0261CEZZ J P352 QPLGN0361CEZZ J P701 QPLGN0260CEZZ J P702 QPLGN0360CEZZ J P705 QPLGN0361CEZZ J P707 QPLGN0361CEZZ J SC401 QSOCZ0840CEZZ J SC402 QSOCZ1040CEZZ J RDA765 PRDAR0232PEFW R RDA766 PRDAR0295PEFW R QCNW-2211PEZZ R QCNW-5509PEN3 R LX-BZ3049GEFD J LX-BZ3100CEFD J
Relay, 12V
AH
Relay, 12V Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Plug, 2-pin (SP) Plug, 3-pin (OR) Plug, 2-pin (M) Plug, 3-pin (E) Plug, 3-pin (OC) Plug, 3-pin (PG) Socket, 8-pin (MA) Socket, 10-pin (MB) Heat Sink, for IC765 Heat Sink, for IC701 Connecting Cord Connecting Cord Screw Screw
AH AB AB AB AC AC AC AB AB AC AC AB AB AD AD AF AE AD AD AA AA
RESISTORS
[M-Ox. Metal Oxide, M-Film Metal Film] VRD-RA2BE750J J 75 1/8W Carbon VRW-KP3HC1R8K J 1.8 5W Cement RR-HZ0046CEZZ J 2.7M 1/2W Solid or VRC-UB2HG275K or RR-DZ0047CEZZ or RR-DZ0046CEZZ VRD-RM2HD154J J 150k 1/2W Carbon VRN-VV3DBR15J J 0.15 2W M-Film or RR-NZ0048CEZZ VRS-SV2HC471J J 470 1/2W M-Ox.
AA AC AD
AA AB AA
94
13VT-N200
Ref. No. Part No. 5 Description Code Ref. No. Part No. 5 Description Code
PWB-D: DUNTKA041WEV0
FRONT AV Unit
MISCELLANEOUS PARTS
J401 P708 QJAKF0058CEZZ J Jack, Video IN/Audio IN QPLGN0342CEZZ J Plug, 3-pin (PG) AE AA 1 2 4 5 6 7 8 9 10 11 12 15 16 17 18 19 20 21 22 23 24 25 26 27 29 30 31 32 33 34 35 36 37 38 39 40 41 43 44 45 46 47 48 49 50 51 52 53 55 56 57 58 59 60 61 62 63 65 66 67 68 69
MECHANISM CHASSIS
LBNDK1011AJZZ LBOSZ1007AJZZ LBOSZ1006AJZZ LCHSM0166AJZZ LHLDZ2016AJZZ LPOLM0063GEZZ LPOLM0064GEZZ MLEVF0518AJZZ V V V V V J J V Tension Band Assy Tension Arm boss Cassette Stay L Main Chassis Assy Loading Motor Block Supply Pole Base Assy Take-Up Pole Base Assy Take-Up Loading Arm Assy Supply Loading Arm Assy Pinch Drive Lever Assy Pinch Roller Lever Assy Tension Arm Assy A/C Head Plate Sifter Drive Lever Pinch Double Action Lever Reverse Guide Lever Assy Reverse Drive Lever Slow Brake Lever Open Lever Clutch Lever Sup Main Brake Assy Take-Up Main Brake Assy Auto Head Cleaner Assy Shifter Reverse Guide Spring 2 Loading Double Action Spring Pinch Double Action Spring Earth Spring Tension Spring Reel Belt Reel Disk Loading Connect Gear Master Cam Casecon Drive Gear Take-Up Loading Gear Supply Loading Gear Pinch Drive Cam Reel Relay Gear Worm Gear Worm Wheel Gear Idler Wheel Assy Motor Pulley Limitter Pulley Assy Guide Roller Tension Pole Adjuster Guide Roller Spring Light Guide FFC for Drum Motor FFC for A/C Head A/C Head PWB Socket, 6-pin Full Erase Head A/C Head Assy Loading Motor Capstan Motor Drum Drive Motor Upper and lower Drum Assy Drum Earth Brush Drum Drive Motor Mounting Screw (SW2.6P+5S) Drum Base PWB(LDG Motor) Socket(LDG Motor) AH AD AD BA AG AM AM AF AF AG AW AH AG AE AD AL AD AE AD AE AF AF AG AH AE AE AD AC AD AE AE AD AE AD AF AD AE AE AD AD AK AD AM AL AB AC AE AG AF AE AB AM AV AK BA AX BP AD AA AL AE AE
MLEVF0519AJZZ V MLEVF0499AJZZ MLEVF0500GEZZ MLEVF0496AJZZ LANGF9620AJFW MLEVP0271AJZZ MLEVP0272AJZZ MLEVP0301AJZZ MLEVP0275AJZZ MLEVP0292AJZZ MLEVP0290AJZZ MLEVP0293AJZZ MLEVP0294AJZZ MLEVP0295AJZZ CLEVP0287AJZZ MSLiP0010AJZZ MSPRD0175AJFJ MSPRT0402AJFJ V J V V V V V V V V V V V V V V V
MSPRT0403AJFJ V MSPRC0213AJFJ V MSPRT0416AJFJ V NBLTK0067AJ00 V NDAiV1078AJ00 V NGERH1293AJZZ V NGERH1295AJ00 V NGERH1294AJZZ V NGERH1270AJZZ V NGERH1271AJZZ V NGERH1272AJZZ V NGERH1299AJZZ V NGERW1070AJZZ V NGERW1066AJZZ V NiDR-0018AJZZ V NPLYV0162AJZZ V NPLYV0163AJZZ V NROLP0131GEZZ J NSFTP0032AJZZ V MSPRC0217AJFJ V PREFL1011AJZZ V QCNW-0247AJZZ V QCNW-0272AJZZ V QPWBF5469AJZZ V QSOCN0605REN1 V RHEDT0036AJZZ V RHEDU0088GEZZ J RMOTM1078GEZZ J RMOTN2055GEZZ J RMOTP1135GEZZ J DDRMW0029TEX1V QBRSK0041GEZZ J XBPSD26P05J00 V PGiDC0056GEFW J QPWBF5468AJZZ V QPLGZ0292GEZZ J
95
13VT-N200
Ref. No. Part No. 5 Description Code Ref. No. Part No. 5 Description Code
MECHANISM CHASSIS
(Continued)
70 71 MSPRC0223AJFJ V Azimuth Spring MSPRC0224AJFJ V Height Adjusting Spring AC AC
96
13VT-N200
Ref. No. Part No. 5 Description Code Ref. MECHANISM CHASSIS PARTS No.
66
Part No.
Description
Code
H
66
62 66
62
G
63 207 207 50 202
56 202
201
16 71
67
49 51 22
15
D
35
35 5
209 210 211 212 213 223
216 41 43
46
C
43 9 10 224 39 23 21 224 30 36 40 37 48 27 219 45 6 44 208 47 60 68 17 38 34 61
30
A
69
97
13VT-N200
Ref. No. Part No. 5 Description Code Ref. No. Part No. 5 Description Code
98
13VT-N200
Ref. No. Part No. Description Code Ref. No. Part No. CASSETTE 5 HOUSING CONTROL PARTS 5 Description Code
300
301
304
F
306
309 313
310 317
303
C
314 312
307
315 316
99
13VT-N200
Ref. No. Part No. 5 Description Code Ref. No. Part No. 5 Description Code
100
B H F
A
21 16 10 2 32
PWB-B
Ref. No.
1
1-11 1-4 35 36 16 22 41 20 31 17 25 22 33 40 1-7 1-9 22 20 22 14 24 1-8 5 30 24 26 9 26 34 44 24 7 25 38 39 6 19
PWB-A
1-13
2
4 28 1-12 8
PWB-D
1-14
1-9
27
1-2
3
23 24 13
26
Part No. 5 Description Code CABINET AND MECHANICALRef. No. Part No. PARTS
101
1-8
15
PWB-C
25
3 42 43
1-10
5
28 11
1-6
Description
1-3
1-1
1-5
13VT-N200
Code
13VT-N200
Ref. No. Part No. 5 Description Code Ref. No. Part No. 5 Description Code
SUPPLIED ACCESORIES
TGAN-0018PEZZ J TiNS-6893PEZZ J RRMCG1331PESA J Guarantee Card Operation Manual Infrared R/C Unit AD AF AV
PACKING PARTS
(NOT REPLACEMENT ITEM)
SPAKC6618PEZZ SSAKA0031PEZZ SPAKP0095PEZZ SPAKP0110PEZZ SPAKX2691PEZZ TLABN0001PEZZ TLABK0002PEZZ TLABZ0143PEZZ Packing Case Polyethylene Bag Polyethylene Sack Polyethylene Sack Buffer Material Serial Number Label Number Card Label
102
13VT-N200
Ref. No. Part No. 5 Description Code Ref. No. Part No. 5 Description Code
FRONT
REAR
5 Number Card
103
13VT-N200
Ref. No. Part No. 5 Description Code Ref. No. Part No. 5 Description Code
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan
104