You are on page 1of 8

Technical Description T 252

Mining Truck

Operating Weight 129 t/285,000 lbs


Maximum GVW 331 t/730,000 lbs
Engine Output 1725 to 2025 HP
Payload Capacity 173 to 195 t/190 to 215 ton

Mining Power.
Engine Suspensions
Engines available Front Suspension System
DDC/MTU ______________________ 12V4000 System design ________________________ Double A-frame with inclined king
1286 – 1510 kW/1725 – 2025 HP pin for minimum scrub distance
Cummins ________________________ QSK45, K1800E, K2000E Suspension strut ______________________ Nitrogen/oil with integral damping and
1343 – 1492 kW/1800 – 2000 HP cushioning pad for both over stroke
Air cleaners __________________________ Donaldson SRG 20 with restriction and rebound stroke. High component
indicators in cab interchangeability with rear struts
L & M (Mesabi) radiator Rear Suspension System
Reduced parasitic load through large diameter, slow speed radiator System design Three-bar linkage with triangular upper
________________________
fan link to safely transfer 100 % of all side
Air starter (electric start – optional) loads from the frame into the rear axle.
Alternator ____________________________ 24 volt, 75 amp (optional high capa- Two drag links transfer all longitudinal
city alternators available) driving forces directly into the two
Batteries ______________________________ (2) 12 volt, 1150 CCA frame girders
Roll-out power module includes: radiator, engine and alternator on Suspension strut ______________________ Nitrogen/oil with integral damping and
subframe cushioning pad for both over stroke
and rebound stroke. High component
interchangeability with front struts
The Liebherr rear suspension system is unique in that it avoids problems
normally associated with nose cone and other linkage designs.
It also allows less side motion of the rear tires during axle oscillation
Electric Drive System which provides for a wider and more stable stance of the rear
suspension struts.
Manufacturer ________________________ General Electric
Wheel Motors ______________________ GE 788 Statex III
Ratios available – 26.8:1
22.3:1
Alternator ____________________________ GTA–22
Dynamic Retarding ______________ Blown grids (12 element), 3-step
Dump Systems
extended range retarding and retard Dump angle ________________________ 50h
speed control Dump cycle __________________________ 24 seconds (raise)
Optional: 7-step extended range 15 seconds (float)
retarding 12 seconds (power down)
Dump pressure ____________________ 165,5 bar/2400 PSI
Dump cylinders ____________________ 267 mm/10.5” diameter first stage
(two stage) 228 mm/9” diameter second stage

Tires (Radial)
Standard size ________________________ 37 R57
Optional ______________________________ 40 R57
Hydraulics
Dump system
Pump displacement ______________ 360 cm3/22 in3
Delivery __________________________ 681 l/min./180 gpm @ 1900 RPM
Relief pressure ________________ 165,5 bar/2400 PSI
Control valve __________________ main split spool with integral relief
Fluid Capacities Pilot control ________________________
and anticavitation poppets
electronic joystick operation
Fuel tank ____________________________ 2460 l/650 gal, Steering and brake systems
optional capacities available Pump displacement ________ 131 cm3/8 in3
Hydraulic tanks Delivery __________________________ 249 l/min./65.8 gpm @ 1900 RPM
Hoist system __________________ 927 l/245 gal Relief pressure ______________ 200 bar/2900 PSI
Brake and steering __________ 510 l/135 gal Operating pressure __________ 179 bar/2600 PSI
Front brakes __________________ 179 bar/2600 PSI
Rear brakes
(arm. speed) __________________ 93 bar/1350 PSI
Steering ________________________ 179 bar/2600 PSI
Accumulator backup ____________ meets SAE J53
Brakes __________________________ (2) 7,6 l/ 2 gal
Braking Systems Steering ________________________ (1) 94,6 l/25 gal
Service Filtration (both systems) ______ meets ISO 15/13 @ 5 m and 15 m
Standard front ________________ wheel speed disc, three (3) calipers respectively (effective, per unit volume)
on a 1143 mm/45” O.D. Disc
Standard rear ________________ dual disc armature speed, two
635 mm/25” O.D. Disc/Side one
caliper/disc
Dynamic retarding ________________ 2376 kW/3300 HP maximum con-
Frame
tinuously rated (12 resistors) blown Material __________________________________ ASTM A710 with high impact resistance
grids. Optional two speed overspeed (high charpy), high strength
retarding and extended range retard- (to 95,000 PSI), good fatigue properties,
ing good weldability.
Steel castings in stress concentration
areas
Design ____________________________________ Closed box structure with multiple
tubular cross members and internal
stiffeners
Steering (with standard tires) Welding __________________________________ Both frame girders welded inside and
out with 100 % ultrasonic inspection to
Vehicle clearance circle ________ 30,2 m/99 ft 2 in AWS D 1.1.
Centerline of tire __________________ 24,7 m/81 ft Liebherr truck frames were developed using computer aided design,
Service ________________________________ Ackerman full-hydraulic steering finite element analysis and 3-D modeling. The combination of high
system with simple, straight forward strength steel, quality welding and modern manufacturing procedures
cross link arrangement insures a frame with exceptional durability and superior resistance to
Auxiliary ______________________________ accumulators sized to meet SAE J53 high impact loads.

Technical Data
2
E

F
H

C A
B D

Dimensions *
SAE turning radius R = DIM “A”
A Wheelbase 5,8 m/19’1”
B Front track 5,9 m/19’3” curb clearance R = DIM “B”
C Rear track 4,8 m/15’8”
D Overall length 13,3 m/43’6”
E Width 7,1 m/23’3”
F Height (over canopy) 6,4 m/21’3”
G Height (canopy-body up – not shown) 6,5 m/40’0”
H Height (loading, standard body) 5,6 m/18’4”

Weights *
Empty Loaded
kg lbs kg lbs
Front 53.435 117,800 107.050 236,000
Rear 75.840 167,200 217.250 479,000
Total 129.275 285,000 324.300 715,000

Dump Body Capacity (Standard)


Struck 76,5 m3/100 yd3
2:1 Heaped 107,8 m3/141 yd3

Note: Various body sizes available to suit application

* with standard 37.00 x 57 tires

Turning Radius
DIM “A” DIM “B”
37.00 R57 tires R 12,34 m/40’6” R 13,01 m/42’ 8”
40.00 R57 tires R 13,60 m/44’7” R 14,28 m/46’10”

Technical Data
3
Cab (deluxe type) Instrumentation
x Driver seat – mechanical suspension base x Air pressure gauge with low pressure alarms, visual and
x Dual dome light audible (not available on airless trucks)
x Double shell concept for safety, thermal and acoustical x Engine
isolation – Hour meter
x Cigarette lighter and ash tray – Oil pressure gauge
x Passenger seat w/seat belt – Water temperature gauge
x Tilt steering wheel with telescopic column x Warning lights for
x High capacity heater and defroster – Engine fault
x Cab wiring interface w/multi-pin connectors – Wheel motor air flow
x Environmentally controlled cab includes: – Park brake
– Plush upholstery and heavy duty acoustical package – Steering pressure
– Heavy duty thermal insulation – Brake pressure (low)
– Filtered heater air – Body up

Cab Standard Equipment Cab Standard Equipment


x Double shell concept for safety and insulation x AM/FM radio w/ cassette
x Fully adjustable operator seat w/ air suspension and x Digital dash instrumentation
double lumbar support Speedometer, Engine -oil pressure, -water temperature,
x Passenger seat w/ mechanical suspension -tachometer, Engine fault, Wheel motor air flow, Park
x Seat belts brake, Steering pressure, Brake pressure (low), Body up,
x Safety glass all around w/ tinted windshield Drive system fault, Ground fault indicator. 24 V system
x Windshield wiper, single blade, electric voltage, Fuel gauge, etc.
x Rearview Mirrors (right and left) x Turn signals w/ emergency flashers
x Tilt and telescopic steering wheel w/ Horn
x Sun visors (3), dome lights
x Fresh, filtered heater and defroster air
x Circuit breaker panel
x 12 Volt power supply
Cab Optional Equipment
x ROPS (Roll Over Protective Structure)
x Air- Conditioning with filtered air
x AM/FM radio w/ CD player

Operator’s Cab
4
Chassis (with Std. engine)
L Length 10267 mm 404.2 in
H H Height 3185 mm 125.4 in
W Width 3353 mm 132.0 in
Weight 43092 kg 95,000 lb
W L

Superstructure assembly
L Length 6955 mm 273.8 in
H H Height 2575 mm 101.4 in
W Width 3315 mm 130.4 in
Weight 5280 kg 11,640 lb
L W

L Spindle and king pin assembly


L Length 1158 mm 45.6 in
H Height 1085 mm 42.7 in
H Weight 944 kg 2,080 lb

Front suspension
L
L Length 1026 mm 40.4 in
l Diameter 432 mm 17.0 in
Weight 735 kg 1,621 lb

W L Fuel tank
L Length 1798 mm 70.8 in
H Height 1821 mm 71.7 in
H W Width 1433 mm 56.4 in
Weight 1145 kg 2,525 lb

L W
Hydraulic tank
L Length 1433 mm 56.4 in
H Height 1320 mm 52.0 in
H W Width 1417 mm 55.8 in
Weight 645 kg 1,421 lb

Lower control arm


L Length 1387 mm 55.2 in
H H Height 1443 mm 56.8 in
W Width 359 mm 14.1 in
Weight 304 kg 670 lb

W L

Upper control arm


L Length 1453 mm 57.2 in
H H Height 1219 mm 48.0 in
W Width 467 mm 18.4 in
Weight 313 kg 690 lb
W L

Shipping Dimensions and Weights


5
L Rim
L Length 900 mm 35.4 in
l Diameter 1735 mm 68.3 in
Weight 1240 kg 2,733 lb

Front hub
L Length 594 mm 23.4 in
l Diameter 1341 mm 52.8 in
Weight 975 kg 2,150 lb

W L
Cab (standard)
L Length 2156 mm 84.9 in
H Height 1600 mm 63.0 in
H
W Width 1658 mm 65.3 in
Weight 1044 kg 2,300 lb

L Rear suspension
L Length 813 mm 31.0 in
l Diameter 432 mm 17.0 in
Weight 585 kg 1,288 lb

Hoist ram
L L Length 2159 mm 85.0 in
l Diameter 330 mm 13.0 in
Ø Weight 646 kg 1,424 lb

Alternator
L
L Length 1715 mm 67.5 in
H Height 1125 mm 44.3 in
H W W Width 1057 mm 41.6 in
Weight 3051 kg 6,725 lb

L Engine
L Length 2685 mm 105.7 in
H Height 2337 mm 92.0 in
H Weight DDC/MTU 4672 kg 10,300 lb
Cummins 5580 kg 12,300 lb

L W
Wheelmotor
L Length 2362 mm 93.0 in
H Height 1577 mm 62.1 in
H W Width 1638 mm 65.4 in
Weight 10274 kg 22,650 lb

Maintenance Dimensions and Weights


6
W L
Engine assembly
L Length 5334 mm 210.0 in
H Height 2774 mm 109.2 in
H W Width 2692 mm 106.0 in
Weight DDC/MTU 12568 kg 24,950 lb
Cummins 12233 kg 26,970 lb

Ø
Tire and rim
l Diamter 1753 mm 69.0 in
H Height 899 mm 35.4 in
H Weight 4537 kg 10,000 lb

L W Air cleaner
L Length 1178 mm 46.4 in
H Height 1193 mm 46.6 in
H W Width 700 mm 27.6 in
Weight 186 kg 410 lb

Truck Standard Equipment Truck Standard Equipment


x D/C Electric Drive System w/ Blown grids & 3 step x Back-up warning alarm
extended tange retarding. x Service lights in control box, engine compartment and
x HD Truck frame (A 710), welded inside and out, tubular axle box
cross members w/ external dump cross carriage x Access ladder lights
x Cast steel components in stress areas x Auxiliary dump, brake, and steering connectors
x Double A-frame front suspension system x Fuel gauge on tank
w/ inclined king pin x Mud flaps – front
x Nitrogen/oil suspension struts w/ 100 % internal x Rear wheel rock ejectors
component commonality front and rear x Hand held fire extinguishers (2)
x Three-bar linkage rear suspension w/ triangular upper x Payload weigh system w/ in cab display
link and two drag links x Liebherr white paint
x Roll-out power module w/radiator, engine and
alternator on sub frame
x Two stage hoist cylinders
x L&M (Mesabi) radiator
Truck Optional Equipment
x Large diameter, low RPM radiator fan for reduced x Electric starter
parasitic load x Automatic air cleaner dust ejectors
x Rockford fan clutch x Engine heater
x Air starter x Cold climate kits
x 2 HD Batteries x Radiator header tank sight gauge
x Engine shutdown at ground level x Sight glass on fuel & hydraulic tank
x Spring applied-pressure released park brake x Centralized service system – additional functions
x Accumulator back-up on steering & hydraulic brake x Auto lube system
system with auto bleed down feature x Diagonal, retractable access ladder
x Dual access ladders and deck hand rails x Additional headlights
x Dual ladder service access to engine area x Additional clearance lights
x Centralized service center w/ dry break pressure x High density fog lights
refueling x Hub-odometer
x Headlights (4) x External display for payload weigh system
x Tail lights: x Additional mud flaps
– Service brake – red x Fire suppression system (multiple actuation options)
– Dynamic retard – amber x Exhaust heated body
– Back up – white x Body liner/wear package(s)
– Turn signals – red x Tailgate for coal body
x Deck mounted back up light – driver side x Canopy spill guards
x Deck mounted clearance lights – amber x Special paint

Maintenance Dimensions and Weights


7
LFR/SP 10000598-2.5-12.00 Printed in Germany by Wolf. Illustrations and data may differ from standard equipment. Subject to change without notice.

LIEBHERR MINING EQUIPMENT CO., 4100 Chestnut Avenue, Newport News, VA 23607, USA,
ç (7 57) 2 45-52 51, Fax (7 57) 9 28-87 55, www.liebherr.com, E-Mail: info@lme.liebherr.com

With compliments:

You might also like