Professional Documents
Culture Documents
Account Active: SIP Server: Outbound Proxy: SIP Transport: NAT Traversal (STUN): SIP User ID: Authenticate ID: Authenticate Password: Name: Use DNS SRV: User ID is phone number: SIP Registration: Unregister On Reboot: Outgoing Call without Registration: Register Expiration: Local SIP port: Local RTP port: Use Random Port: Refer-To Use Target Contact: Validate Incoming Message: SIP T1 Timeout: SIP T2 Interval: DTMF Payload Type: DTMF in Audio: DTMF via RFC2833: DTMF via SIP INFO: Send Hook Flash Event: Enable Call Features: Proxy-Require: Use NAT IP:
60
No
UDP No
TCP
TLS (default is UDP) Yes (the user part of an SIP address) (can be identical to or different from SIP User ID) (purposely not displayed for security protection) (optional, e.g., John Doe)
No No No No No
5062 5012
Yes Yes Yes Yes Yes (in minutes. default 1 hour, max 45 days) (default 5062) (1024-65535, default 5012) Yes Yes Yes
No No No
0.5 sec 4 sec
101
No No No No No
Yes Yes Yes Yes (Hook-Flash will be sent as a DTMF event if set to Yes) Yes (if Yes, call features using star codes will be supported locally)
Distinctive Ring Tone: Disable Call-Waiting: Disable Call-Waiting Tone: Ring Timeout: Early Dial: Dial Plan Prefix: Use # as Dial Key: Dial Plan : SUBSCRIBE for MWI:
used if incoming caller ID is used if incoming caller ID is used if incoming caller ID is Yes Yes
No No
60
(10-300, default is 60 seconds) No No Yes (use "Yes" only if proxy supports 484 response) (this prefix string is added to each dialed number) Yes (if set to Yes, "#" will function as the "Dial" key)
{ x+ }
Yes, send periodical SUBSCRIBE for Message Waiting Indication Anonymous Call Rejection: Special Feature: Session Expiration: Min-SE: Caller Request Timer: Callee Request Timer: Force Timer: UAC Specify Refresher: UAS Specify Refresher: Force INVITE: Preferred Vocoder: (in listed order) No
Standard 180 90
Yes (in seconds. default 180 seconds) (in seconds. default and minimum 90 seconds) Yes (Request for timer when making outbound calls) Yes (When caller supports timer but did not request one) Yes (Use timer even when remote party does not support) UAS Omit (Recommended) UAS (When UAC did not specify refresher tag) Yes (Always refresh with INVITE instead of UPDATE)
PCMU PCMA G.723 G.729AB G.726-32 iLBC G.726-40 G.729E
No No No UAC UAC No choice 1: choice 2: choice 3: choice 4: choice 5: choice 6: choice 7: choice 8: 20ms
97 100 99 103 102
G723 Rate: iLBC Frame Size: iLBC Payload Type: G726-16 Payload Type: G726-24 Payload Type: G726-40 Payload Type: G729E Payload Type: VAD: Symmetric RTP: Fax Mode: Fax Tone Detection Mode: Jitter Buffer Type: Jitter Buffer Length: SRTP Mode: Caller ID Scheme: Caller ID Minimum RX Level (dB): Caller ID Transport Type: Hook Flash Timing: Gain:
(between 96 and 127, default is 97) (between 96 and 127, default is 100) (between 96 and 127, default is 99) (between 96 and 127, default is 103) (between 96 and 127, default is 102) Yes Yes Pass-Through Callee Adaptive Medium High Enabled and forced Enabled but not forced
Bellcore/Telcordia -30
FXO Termination Enable Current No Yes (Default Yes. If set to yes, enter threshold below) Disconnect: Current Disconnect 100 (50-800 milliseconds. Default 100 milliseconds) Threshold (ms): Enable PSTN Disconnect No Yes (Default No) Tone Detection: (If set to yes, the following tone is used as the disconnect signal)
PSTN Disconnect Tone: f1=480@-32,f2=620@-32,c=500/500; (Syntax: f1=freq@vol, f2=freq@vol, c=on1/off1-on2/off2-on3/off3; [...]) (Allowed Range: freq = 0 to 4000Hz; vol = -40 to -24dBm) (Default: Busy Tone: f1=480@-32,f2=620@-32,c=500/500;) AC Termination:
USA
(1-10. Default 4)
(Number of rings for a PSTN incoming call to FXO port before FXO port picks up) No Yes (Default Yes) (If set to yes, all incoming PSTN calls will ring the FXS port after the Ring Thru Delay) (1-10 seconds. Default 4 seconds)
PSTN Ring Thru Delay 4 (sec): Channel Dialing DTMF Digit Length (ms): 100 DTMF Dial Pause (ms): 100 First Digit Timeout (sec): 10 Inter-Digit Timeout (sec): 4 Wait for Dial-Tone: Stage Method (1/2): 2 No
(40-127 milliseconds, Default 100 milliseconds) (40-127 milliseconds, Default 100 milliseconds) (1-20 seconds. Default 10 seconds) (1-15 seconds. Default 4 seconds) Yes (Default Yes - dial upon dial-tone) (Default 2 - 2 stage dialing)
Update Cancel Reboot