Professional Documents
Culture Documents
Categories: Metal; Nonferrous Metal; Aluminum Alloy; 3000 Series Aluminum Alloy
Material Notes: Data points with the AA note have been provided by the Aluminum Association, Inc. and are NOT FOR DESIGN. Composition Notes: Composition information provided by the Aluminum Association and is not for design. Key Words: Vendors: UNS A93004; ISO AlMn1Mg1; Aluminium 3004-O; AA3004-O No vendors are listed for this material. Please click here if you are a supplier and would like information on how to add your listing to this material. Metric 2.72 g/cc Metric 45 179 MPa 30.0 MPa
@Temperature400C
Physical Properties Density Mechanical Properties Hardness,Brinell TensileStrength,Ultimate TensileStrength,Yield Elongation at Break
Comments AA; Typical Comments AA; Typical; 500 g load; 10 mm ball AA; Typical
50.0 MPa
@Temperature300C
7250 psi
@Temperature572F
96.0 MPa
@Temperature200C
13900 psi
@Temperature392F
180 MPa
@Temperature -30.0C
26100 psi
@Temperature -22.0F
180 MPa
@Temperature25.0C
26100 psi
@Temperature77.0F
180 MPa
@Temperature100C
26100 psi
@Temperature212F
200 MPa
@Temperature -100C
29000 psi
@Temperature -148F
290 MPa
@Temperature -200C
42100 psi
@Temperature -328F
AA; Typical
34.0 MPa
@Temperature300C
4930 psi
@Temperature572F
65.0 MPa
@Temperature200C
9430 psi
@Temperature392F
69.0 MPa
@Temperature -30.0C
10000 psi
@Temperature -22.0F
69.0 MPa
@Temperature25.0C
10000 psi
@Temperature77.0F
69.0 MPa
@Temperature100C
10000 psi
@Temperature212F
80.0 MPa
@Temperature -100C
11600 psi
@Temperature -148F
90.0 MPa
@Temperature -200C
13100 psi
@Temperature -328F
25.0 %
@Temperature25.0C
25.0 %
@Temperature77.0F
25.0 %
@Temperature100C
25.0 %
@Temperature212F
26.0 %
@Temperature -30.0C
26.0 %
@Temperature -22.0F
31.0 %
@Temperature -100C
31.0 %
@Temperature -148F
38.0 %
@Temperature -200C
38.0 %
@Temperature -328F
55.0 %
@Temperature200C
55.0 %
@Temperature392F
80.0 %
@Temperature300C
80.0 %
@Temperature572F
90.0 %
@Temperature400C
90.0 %
@Temperature752F
10.0 - 18.0 %
10.0 - 18.0 %
Page 1 / 2
ModulusofElasticity NotchedTensileStrength UltimateBearingStrength BearingYieldStrength PoissonsRatio FatigueStrength Machinability ShearModulus ShearStrength Electrical Properties ElectricalResistivity MagneticSusceptibility Thermal Properties CTE, linear SpecificHeatCapacity ThermalConductivity MeltingPoint Solidus Liquidus Processing Properties AnnealingTemperature Component Elements Properties Aluminum,Al Copper,Cu Iron,Fe Magnesium,Mg Manganese,Mn Other,each Other,total Silicon,Si Zinc,Zn References for this datasheet.
20.0 %
@Thickness 1.59 mm
20.0 %
@Thickness 0.0625 in
AA; Typical AA; Typical AA; Typical; Average of tension and compression. Compression modulus is about 2% greater than tensile modulus. 2.5 cm width x 0.16 cm thick side-notched specimen, Kt = 17. Edge distance/pin diameter = 2.0 Edge distance/pin diameter = 2.0 completely reversed stress; RR Moore machine/specimen 0-100 Scale of Aluminum Alloys AA; Typical Comments AA; Typical cgs/g at 25C Comments
25.0 %
@Diameter 12.7 mm
25.0 %
@Diameter 0.500 in
68.9 GPa 165 MPa 317 MPa 138 MPa 0.350 96.5 MPa
@# of Cycles 5.00e+8
10000 ksi 23900 psi 46000 psi 20000 psi 0.350 14000 psi
@# of Cycles 5.00e+8
23.2 m/m-C
@Temperature 20.0 - 100C
12.9 in/in-F
@Temperature 68.0 - 212F
23.9 m/m-C
@Temperature 20.0 - 100C
13.3 in/in-F
@Temperature 68.0 - 212F
24.1 m/m-C
@Temperature 20.0 - 200C
13.4 in/in-F
@Temperature 68.0 - 392F
25.1 m/m-C
@Temperature 20.0 - 300C
13.9 in/in-F
@Temperature 68.0 - 572F
25.1 m/m-C
@Temperature 20.0 - 300C
13.9 in/in-F
@Temperature 68.0 - 572F
average
0.893 J/g-C 163 W/m-K 629.4 - 654C 629.4C 654C Metric 413C Metric 95.5 - 98.2 % <= 0.25 % <= 0.70 % 0.80 - 1.30 % 1.0 - 1.50 % <= 0.050 % <= 0.15 % <= 0.30 % <= 0.25 %
0.213 BTU/lb-F 1130 BTU-in/hr-ft-F AATypicalat77F 1165 - 1210F AA; Typical range based on typical composition for wrought products 1/4 inch thickness or greater 1165F AA; Typical 1210F AA; Typical English 775F English 95.5 - 98.2 % <= 0.25 % <= 0.70 % 0.80 - 1.30 % 1.0 - 1.50 % <= 0.050 % <= 0.15 % <= 0.30 % <= 0.25 % Comments
Comments As remainder
Some of the values displayed above may have been converted from their original units and/or rounded in order to display the information in a consistent format. Users requiring more precise data for scientific or engineering calculations can click on the property value to see the original value as well as raw conversions to equivalent units. We advise that you only use the original value or one of its raw conversions in your calculations to minimize rounding error. We also ask that you refer to MatWeb's terms of use regarding this information. Click here to view all the property values for this datasheet as they were originally entered into MatWeb.
Page 2 / 2