Professional Documents
Culture Documents
HARDWARE MANUAL
Trademarks
All brand names and product names used in this document are trademarks, registered trademarks, or trade names of the respective holders. Order additional copies of this manual and other ATI publications from: Aristocrat Technologies, Inc. 7230 Amigo Street Las Vegas, NV 89119 Tel: (800) 748-4156 Fax: (702) 270-1136 A User Response form is provided at the back of this document for customer comments. Mail or fax this form or any other comments to the address above.
20 Jan 2006
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
ii
Contents
Proprietary Copyright Notice................................................................................ ii
Trademarks ............................................................................................................................... ii
Contents .................................................................................................................. iii List of Figures..........................................................................................................vi List of Tables ......................................................................................................... vii Introduction..............................................................................................................1 Installation ................................................................................................................1
Locks..........................................................................................................................................1
Cams................................................................................................................................................................2
Operation ..................................................................................................................6
Lock and Control Switch Locations ..........................................................................................6 Main Door..................................................................................................................................7
Opening ...........................................................................................................................................................7 Closing ............................................................................................................................................................7
Belly Door..................................................................................................................................7
Opening ...........................................................................................................................................................7 Closing ............................................................................................................................................................7
Maintenance .............................................................................................................9
Coin Acceptor ............................................................................................................................9
Removal...........................................................................................................................................................9 Installation ......................................................................................................................................................9
Coin Hopper.............................................................................................................................10
Removal.........................................................................................................................................................10 Installation ....................................................................................................................................................10
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Installation ....................................................................................................................................................13
Sound Board.............................................................................................................................22
Removal.........................................................................................................................................................22 Installation ....................................................................................................................................................22
Troubleshooting .....................................................................................................28
Power Supplies ........................................................................................................................28 VIG-520 SCX Logic Board Indicators ....................................................................................29 VIG 520 Logic Board Jumper Settings....................................................................................30 Backplane Connections............................................................................................................31
Troubleshooting Techniques.................................................................................33
Problem: Bill Validator Errors.................................................................................................33 Power Supply Troubleshooting ...............................................................................................34
Problem: 5/12 Volt DC Power Supply Inoperable........................................................................................34 Problem: 5/24-Volt DC Power Supply Inoperable .......................................................................................34
20 Jan 2006 iv
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Problem: Coin Acceptor Errors....................................................................................................................34 Problem: Coin Diverter Inoperable..............................................................................................................34 Problem: Machine Lamps Inoperable...........................................................................................................34 Problem: Key Switches and Button Inoperable ............................................................................................35
Appendix A .............................................................................................................36
Parts Lists* and Exploded View Drawings .............................................................................36
Cabinet 1 .......................................................................................................................................................37 Cabinet 2 .......................................................................................................................................................39 Reel Shelf Assembly.......................................................................................................................................40 Reel Mechanism Assembly ............................................................................................................................42 Door (Reel Glass)..........................................................................................................................................43 Door (Coin Acceptor/Door Hardware).........................................................................................................44 Door (Various Hardware).............................................................................................................................45 Door (Coin Panel).........................................................................................................................................46 Belly Door .....................................................................................................................................................47 Buttons ..........................................................................................................................................................48 Coin Acceptor................................................................................................................................................51
User Response.........................................................................................................54
20 Jan 2006
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
List of Figures
Figure 1 Typical Lock Installation ..................................................................................................................1 Figure 2 Lock Cams ........................................................................................................................................2 Figure 3 Cabinet Dimensions: SCX Casino Top Configuration .....................................................................4 Figure 4 Cabinet Dimensions: SCX Round Top and Chop Top Configurations ............................................4 Figure 5 Machine Footprint.............................................................................................................................5 Figure 6 Mounting Bolt Components..............................................................................................................6 Figure 7 Lock and Key Switch Locations .......................................................................................................6 Figure 8 Typical Coin Acceptor and Bracket..................................................................................................9 Figure 9 Hopper ............................................................................................................................................10 Figure 10 Main Logic Board.........................................................................................................................11 Figure 11 Lottery Monitor Board Wiring Diagram.......................................................................................13 Figure 12 Reel Assembly - Side View ..........................................................................................................15 Figure 13 Backplane Board and Surrounding Hardware Exploded View .................................................16 Figure 14 Backplane I/O Board ....................................................................................................................18 Figure 15 I/O Expansion Board ....................................................................................................................19 Figure 16 Handle - Exploded View...............................................................................................................20 Figure 17 Sound Board .................................................................................................................................22 Figure 18 Belly Door Exploded View........................................................................................................24 Figure 19 Small Deck Buttons Exploded View .........................................................................................25 Figure 20 Micro-switch and Socket ..............................................................................................................26 Figure 21 Deck Button Legend and Cap.......................................................................................................27 Figure 22 Power Supply and Fuses ...............................................................................................................28 Figure 23 VIG-520 LED Key .......................................................................................................................29 Figure 24 Logic Board Jumper Settings and Locations ................................................................................30 Figure 25 Backplane (Part Number 07-10168B1*) ......................................................................................31 Figure 26 SCX 5-Reel Stepper Casino Top ..................................................................................................36 Figure 27 Cabinet 1 Power Supply, Hopper and Bracket Installations......................................................37 Figure 28 Cabinet 2 Handle Mechanism and WBA Bill Validator Components.......................................39 Figure 29 Reel Shelf Assembly Exploded View........................................................................................40 Figure 30 Reel Assembly - Exploded view...................................................................................................42 Figure 31 Main Door Assembly....................................................................................................................43 Figure 32 Door Hardware Exploded View ................................................................................................44 Figure 33 Main Door Brackets, Buttons, Bezels, and Bushing..................................................................45 Figure 34 Main Door Belly Components ...................................................................................................46 Figure 35 Belly Glass Assembly ...................................................................................................................47 Figure 36 Deck Buttons ................................................................................................................................48 Figure 37 10-Button Deck.............................................................................................................................49 Figure 38 11-Button Deck.............................................................................................................................50 Figure 39 Coin Acceptor Mounting ..............................................................................................................51 Figure 40 Game Top Access Notches ...........................................................................................................52 Figure 41 PMM Tray Glass Removal ...........................................................................................................53
20 Jan 2006
vi
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
List of Tables
Table 1 Physical Characteristics......................................................................................................................3 Table 2 Power Requirements ..........................................................................................................................3 Table 3 Environment.......................................................................................................................................3 Table 4 Lottery Monitor Kit (00-71344) Parts List.......................................................................................12 Table 5 Power Supplies and Associated Components ..................................................................................28 Table 6 LED Descriptions.............................................................................................................................29 Table 7 Backplane Connectors......................................................................................................................32 Table 8 Part Number List for Hopper and Power Supply .............................................................................37 Table 9 *Meter Assembly (07-40162) Parts Breakdown ...........................................................................38 Table 10 Handle and Bill Validator Part Numbers .......................................................................................39 Table 11 Reel Shelf Assembly Parts List ......................................................................................................40 Table 12 *5-Reel Assembly (07-41421) Parts Breakdown........................................................................41 Table 13 Reel Assembly Parts List ...............................................................................................................42 Table 14 Main Door Parts List Glass and Lights .......................................................................................43 Table 15 Main Door Parts List Brackets and Backplates...........................................................................44 Table 16 Main Door Assembly Parts List Brackets, Buttons, Bezels, and Bushing ..................................45 Table 17 Main Door Belly Parts List ............................................................................................................46 Table 18 Belly Parts List...............................................................................................................................47 Table 19 6-Button Deck Panel Parts List ......................................................................................................48 Table 20 10-Button Panel Assembly Parts List (07-41427)..........................................................................49 Table 21 11-Button Deck Parts List ..............................................................................................................50 Table 22 Coin Acceptor Mounting Parts List ...............................................................................................51
20 Jan 2006
vii
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Introduction
This manual provides reference materials for the Aristocrat Technologies, Inc.(ATI), VIG-520 SCX upright 5-reel (SCX 5-Reel) slot machine, part number US-03152-002. Procedures are provided for the proper installation of the machine on the casino floor, performing day-to-day machine operations, troubleshooting, and routine machine maintenance. Machine and sub-assembly exploded view drawings and part numbers are provided in Appendix A.
Installation
Locks
To ensure maximum security, the property should install permanent locks during machine installation. Refer to the Operation section of this manual on page 6 for lock locations. Temporary thumb-turn shipping locks (non-keyed) are installed by ATI on the following:
Main Door To unlock, rotate key counter-clockwise 90 Belly Door To unlock, rotate key counter-clockwise 90 Logic Door To unlock, rotate both keys clockwise 90 Bill Stacker To unlock, rotate key counter-clockwise 90
These locks are provided to prevent damage to machine components during shipment. The temporary locks should be replaced with 5/8-inch barrel locks with the same rotation direction and degree of rotation as listed above for the shipping locks. The existing lock cams should be used. If the machine was delivered without temporary locks, install the machine locks with the appropriate cams (packed with machine). Refer to the Cams section when installing the new locks.
20 Jan 2006
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Cams
Install the appropriate cam on the locks for the main door, belly door, and logic door. Refer to the illustration below when installing locks and cams.
20 Jan 2006
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
0 - 80% non-condensing
0 - 95% non-condensing
20 Jan 2006
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Cabinet Dimensions
Figure 4 Cabinet Dimensions: SCX Round Top and Chop Top Configurations
20 Jan 2006
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Secure the machine to the support or cabinet with 5/16-inch carriage bolts, flat washers, and nuts (4 places) as shown on the following page.
20 Jan 2006
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Operation
Lock and Control Switch Locations
20 Jan 2006
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Main Door
The main door provides access to all areas of the machine including the top box. Logic compartment and bill validator cash box access requires additional keys as required by gaming regulation and/or local procedures.
Opening
1. Insert the key into the main door lock and turn it clockwise 90. 2. Lift the main door latch to the top of the slot and pull the door open.
Closing
1. Verify that the bill validator head is fully inserted so that it does not interfere with the door being closed. 2. Push on the door until the door latch drops to the bottom of the slot. 3. Turn the main door key counter-clockwise 90 and remove it from the lock.
Belly Door
An additional door is provided on the lower portion of the main door to allow access to the bill validator bill stacker without opening the main door. This door also provides easy access to change the belly glass and the door fluorescent lamp.
Opening
1. Unlock the belly door by inserting the key into the door lock and turning it clockwise 90. 2. Place one hand at the top of the belly door and push the access latch on the right side of the main door. 3. Lower the door until it is held firmly by the safety chain.
Closing
1. Lift the top of the belly door until it touches the main door. 2. Push firmly on the top until it latches. 3. Lock the belly door by inserting the key into the door lock and turning it counter-clockwise 90.
20 Jan 2006
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
20 Jan 2006
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Maintenance
Coin Acceptor
Removal
1. Open the main door and turn off the AC power. 2. Disconnect the wiring harness cable connector from the coin acceptor. 3. Lift the two latches (shown below) with your thumbs while pulling forward on the top of the coin acceptor with your forefingers. 4. Lift the acceptor out of the bracket lower guide slots.
Installation
1. Insert the acceptor lower guide pins into the slots on the bracket. 2. Push the top of the acceptor into the bracket until the two upper guide pins are firmly latched by the spring latches. 3. Plug the wiring harness connector into the coin acceptor connector. 4. Turn on the machine AC power and close the main door.
20 Jan 2006
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Coin Hopper
Removal
1. Open the main door and turn off the AC power. 2. Grasp the hopper handle firmly with your left hand and pull forward while balancing the hopper with your right hand. 3. Continue to pull it until the hopper is free of the mounting rails.
Figure 9 Hopper
Installation
1. Grasp the hopper handle firmly with your left hand, and the right side of the coin bowl with your right hand. 2. Lift the hopper until the mounting rails are aligned with the rails on the cabinet base. 3. Push the hopper into the cabinet until it seats firmly into the electrical connector. 4. Turn on the machine AC power and close the main door.
20 Jan 2006
10
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Danger of explosion if lithium battery is incorrectly replaced. Replace only with the same type or equivalent type lithium battery.
WARNING
Always discharge body static before handling main boards. When a main board is removed from the card cage, it must be transported and stored in an anti-static card wrapper to prevent damage. Defective boards should be handled like a new board to prevent additional component failure.
Removal
1. Open the main door and turn off the AC power. 2. Unlock and open the logic door. 3. Grasp the logic board assembly by the plastic release levers, and pull forward to remove it from the logic cage.
20 Jan 2006
11
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Installation
1. Position the board with the components facing upward into the lower slot guide rails in the card cage assembly so the board is aligned with the backplane connectors. 2. Push the board forward within the guide rails until firmly seated. 3. Install and lock the logic access door. 4. Turn on the AC power and close the main door.
Parts Required
Table 4 Lottery Monitor Kit (00-71344) Parts List Item Lottery Monitor Board WV Lottery Monitor Harness Plastic PCB Support Standoff Part Number 07-10208 07-20875 L13187 Quantity 1 1 4
20 Jan 2006
12
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Installation
Refer to the figure below when making electrical connections.
1. Attach the four plastic supports to the Lottery Monitor Board. 2. Connect the harness: a. Remove the shrouded door connector from the backplane (J33). b. Plug that connector into J3 (DOOR HARNESS) on the Lottery Monitor Board. c. Connect the Lottery Monitor Harness to the Monitor Board J1 (2-pin POWER) and J2 (10-pin BACKPLANE). d. Plug the other 10-pin shrouded harness connector into J33 (MULTIPLEXED INPUTS 3) on the backplane. e. Plug the remaining harness connector into the MAG CARD READER jack on the backplane (J4). If this connector has 10 pins instead of 13, ensure that pin 1 is aligned with pin 1 on the jack. 3. Remove the backing from the four plastic supports and mount the board inside the cabinet on the left wall next to the bottom of the backplane. The location is not critical, but is limited by the length of the harness, so it is recommended to attach the harness first. 4. Remove the REMOVE BEFORE USE tab from the battery on the monitor board.
20 Jan 2006
13
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Removal
1. 2. 3. 4. Open the main door and turn OFF the AC power. Remove the reels as described in the Reel Replacement section on page 14. Disconnect the two wiring harness power connectors from the power supply cables. Remove two nuts and grounding strap from the power supply so that it can be removed from the cabinet.
Installation
1. Align the new power supply mounting holes with the mounting holes on the power supply base plate and attach screws to mount the power supply to the cabinet. 2. Connect the two power cables and grounding strap previously disconnected. 3. Install the reels as described in the Reel Replacement section on page 14.
Reel Replacement
Removal
1. Open the main door and turn OFF the AC power to the machine. 2. Loosen the screw securing the reel to the front of the reel shelf. 3. Lift upward on the front of the reel base and pull forward so that it disengages from the mounting screw and washer. 4. Remove the reel assembly from the machine.
NOTE:
If removing all reel assemblies, number them and indicate the left- or right-side for the number one reel so they can be returned to the correct position during installation.
Installation
1. 2. 3. 4. Turn OFF the machine AC power. Verify that the reel being installed is the correct one for the position. Place the largest portion of the slot on the reel base over the mounting screw and flat washer. Push the reel back into position while lowering the front lip so that the reel plug slides into the chassis connector. 5. Secure the reel base to the reel shelf with the original mounting screw. 6. Turn ON the machine AC power and close the main door.
20 Jan 2006
14
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Installation
1. Place the new LED in the vacant socket. 2. Replace the drum on the reel, ensuring that the home position (indicated by a bump on side of the reel edge) is aligned with the short pin on the hub. 3. Replace the washer and c-ring. 4. Install the reel as described in the Reel Replacement section on page 14.
20 Jan 2006
15
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
5. 6. 7. 8. 9.
Loosen, but do not remove, the two rear lock nuts. Pull the logic board cage forward so that the slots slip free of the rear mounting studs. Remove the logic board cage from the cabinet. Detach all wire harness connectors from the backplane board. Remove the nine screws securing the backplane board to the backplate. Ensure that the screw inserted into the grounding point is also removed.
CAUTION
Place the defective backplane board in an anti-static bag to prevent further damage to the board during transit.
20 Jan 2006
16
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Installation
1. Discharge any static charge before opening the new backplane board package. 2. Install the new backplane board with the original mounting screws. Ensure that the grounding point screw is also reinserted. 3. Plug in all of the wire harness connectors to the backplane board. 4. Slip the rear mounting-hole slots on the logic board cage onto the mounting studs on the reel shelf. 5. Pull the logic board cage forward until the front mounting holes slip into place on the forward mounting studs; use an 11/32-inch nut driver to tighten the lock nuts. 6. Install the logic board in the lower slot on the cage; install and lock the logic door; and install the coin hopper. 7. Turn ON the AC power and test the machine to insure that the new backplane board is functioning correctly.
20 Jan 2006
17
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Removal
1. Open the main door and turn OFF the AC power. 2. Disconnect the three cables from the expansion board. 3. Lift the board away from the backplane, being careful not to crack the board.
Installation
1. Insert the new board onto J1 and J2. 2. Connect the three cables to the board. 3. Turn ON the machine AC power and close the door.
20 Jan 2006
18
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Removal
1. Open the main door and turn OFF the AC power. 2. Disconnect all cables from the expansion board. 3. Remove the four screws (if mounted on studs), or cut the four cable ties (if mounted on standoffs).
Installation
1. Install the new board with the four screws or four cable ties. 2. Connect all cables to the board. 3. Turn ON the machine AC power and close the door.
20 Jan 2006
19
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
3. Disconnect the handle solenoid and handle switch which are attached to the mounting bracket. 4. Use a -inch hex driver to remove the socket head screw and washer securing the handle to the handle mechanism shaft. 5. Pull the handle and the plastic hubcap from the handle mechanism shaft. 6. Use a 3/8-inch nut driver to remove the four lock nuts securing the handle mechanism to the cabinet. 7. Pull the handle mechanism from the cabinet.
20 Jan 2006
20
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Installation
1. Place the handle mechanism in the cabinet so that the mounting stud slots and holes slide over the cabinet studs. 2. Use a 3/8-inch nut driver to tighten the four lock nuts. A nut is not used on the lower rear stud. 3. Slide the plastic hubcap over the handle shaft so that the handle hole is aligned with the hole on the shaft. 4. Insert the handle into the hole on the mechanism shaft so that the flat guide on the handle aligns with the flat area in the hole on the mechanism shaft. 5. Insert the socket head screw and washer into the hole on the hub cap and tighten it with a inch hex drive. 6. Reconnect the handle solenoid and handle switch which are attached to the mounting bracket. 7. Reinstall the reels previous removed and ensure they are replaced in the correct locations. 8. Turn ON the machine AC power and close the main door. 9. Access the Operator Menu and access the HANDLE MECH option from the MACHINE TEST menu. Pull the handle and verify that it releases and latches correctly.
20 Jan 2006
21
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Sound Board
The sound board is located on the lower left side of the cabinet.
Removal
1. 2. 3. 4. Open the main door and turn OFF the AC power. Disconnect the three cables from the sound board. Remove the four mounting screws securing the sound board to the cabinet. Remove the four chips in sockets U3, U4, U5, and U6 with a chip puller and set aside.
Installation
1. Insert the four chips in sockets U3, U4, U5, and U6 ensuring that the chips are in the correct sockets. 2. Align the mounting holes on the sound board over the mounting holes on the cabinet. 3. Install and tighten the four mounting screws. 4. Connect the three cables to the sound board. 5. Turn ON the machine AC power and close the door.
20 Jan 2006
22
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
To ensure proper operation and bulb life, replace the starter each time the fluorescent bulb is replaced.
To ensure proper operation and bulb life, replace the starter each time the fluorescent bulb is replaced.
20 Jan 2006
23
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
1. Unlock and open the main door, turn OFF the AC power and close the main door; unlock and open the belly glass door as described in the Operations section of this manual.
2. Disconnect the fluorescent lamp power cable at the inline connectors and remove the four lock nuts securing the fluorescent lamp assembly to the belly glass doorframe. 3. Lift the fluorescent lamp assembly away from the frame and place it in a protected area to prevent breaking the lamp. 4. If the belly glass was not broken, gently push upward on the front side to release it from the foam lining on the frame. 5. Using care to not catch the bottom edge of the glass under the magnetic door switch, remove the glass from the frame and place it in a protected area to prevent breakage. 6. Carefully place the new glass on the frame ensuring that the rubber strip on the frame is not disturbed. 7. Place the fluorescent lamp assembly onto the four mounting studs and secure the fluorescent lamp assembly with the four original lock nuts. 8. Reconnect the fluorescent lamp power previously disconnected. 9. Close and latch the belly glass door, open the main door and turn ON the machine AC power; close and lock the main door.
20 Jan 2006
24
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Deck Buttons
Refer to the illustration below when replacing the deck button assemblies or bulbs.
20 Jan 2006
25
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
3. Use a small screwdriver or small knife blade to lift up on the socket switch-retaining tab.
NOTE: Use caution to prevent cuts in the event of tool slippage.
4. Pull the switch off the retaining pins on the socket and then slide it out of the base of the socket. Note the position of the switch button as shown above. 5. Lift the switch-retaining tab while sliding the new switch onto the retaining pins. Verify the switch button is aligned in the same position as the switch that was removed. 6. Install the wires onto the new micro-switch. 7. Turn ON the machine AC power and close the main door.
20 Jan 2006
26
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
1. Use a sharp object, such as a small screwdriver blade, to pry the cap from the deck button, being careful not to scratch it.
NOTE: Use caution to prevent cuts in the event of tool slippage.
2. Pry the legend (label) insert from the deck button cap, being careful not to scratch the clear plastic cap. 3. Press the new legend (label) insert into the deck button cap. 4. Press the diffuser into the cap with the smooth side toward the legend. This positions the inset ridge of the diffuser toward the switch body. 5. Align the cap with the deck button housing, and then push into the cap. It will click when seated.
20 Jan 2006
27
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Troubleshooting
The troubleshooting section is provided to help diagnose problems encountered with the machine.
Power Supplies
Five red LED indicators located on the lower left corner of the backplane board are provided for quick verification of the machine power supply operation. The following table provides information regarding the various modules within the machine powered by the machine supplies.
NOTE:
These indicators do not provide status of the auxiliary power supplies located in the top compartment of various games.
Table 5 Power Supplies and Associated Components
Power Supply +5 VDC +5 VDC ISO +12 VDC +24 VDC ISO +3 VDC
Modules Supplied Card reader, displays, logic board, keypad, and sound board Handle mechanism, reel drivers, and logic board Card reader, displays, and sound board Coin acceptor, handle mechanism, reel drivers, logic board, and sound board CPU power supply
The DC power supplies are powered from the AC fuses mounted on the reel shelf. The following illustration shows which power supplies are assigned to these fuses:
20 Jan 2006
28
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Serial communications between the machine logic board and internal devices, such as ticket printer and bill validator Serial communications between the machine logic board and external devices/systems, such as slot accounting and player tracking systems, and multi-site progressive systems Logic board logic activity Power supply operation
These indicators are located along the right front edge of the logic board and can be viewed by removing the logic door.
Figure 23 VIG-520 LED Key Table 6 LED Descriptions LED DS1 DS2 DS3 DS4 DS5 DS6 DS7 DS8 DS9 DS10 DS11 DS12 DS13 Port 24 VDC 5 VDC 5 VDC 3 VCD Watchdog Status IDE Port 1 TX Port 1 RX Port 2 TX Port 2 RX Port 3 TX Port 3 RX Not used Not used Accounting Touch screen (not used) GDD (not used) Description Isolated supply Isolated supply Logic supply CPU supply LED DS14 DS15 DS16 DS17 DS18 DS19 DS20 DS21 DS22 DS23 DS24 DS25 Port Port 4 TX Port 4 RX Port 5 TX Port 5 RX Port 6 TX Port 6 RX Port 7 TX Port 7 RX Port 8 TX Port 8 RX Port 9 TX Port 9 RX Ticket printer Smart reel driver (not used) RS-485 Communications (MSP) Terminal port Host port Description Bill validator
20 Jan 2006
29
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Jumper #1
Setting = TTL (e.g. JCM WBA-13 bill validator) Setting = RS-232 (e.g. Mars bill validator)
Jumper #2 Switches the Auxiliary 485 port (J16 and J22) between half duplex and full duplex
Setting = ON
Jumper #4 Enables 512K SRAM chip
Setting = ON
20 Jan 2006
30
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Backplane Connections
20 Jan 2006
31
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Table 7 Backplane Connectors Conn J1 J2 J3 J6 J7 J10 J15 J16 J17 J18 J19 J20 J21 J23 J25 J26 J27 J28 J29 Function Lamp Selects Lamp Drivers Terminal Port Aux Power Port 1 Accounting Port 4 Bill Validator Lamp Returns Lamp Returns Port 5 Host Port 6 Aux Terminal Port 7 In MSP Port 10 RBP ProgresHard Meters 1 Port 9 Ticket Printer Port 7 Out MSP Bill Validator Power Lamp Returns Lamp Returns Hard Meters 2 Conn J30 J31 J32 J33 J34 J35 J36 J37 J38 J39 J40 J41 J42 J45 J46 J47 J48 J49 J50 Function Direct Outputs Sound Board Multiplexed Inputs 1 Multiplexed Inputs 2 Handle Mech Coin Acceptor Multiplexed Inputs 3 Multiplexed Inputs 4 Hopper Bonus LED Meter Slot Display Main Power Aux Power Reel 1 Driver Reel 2 Driver Reel 3 Driver Reel 4 Driver Reel 5 Driver Reel 6 Driver
20 Jan 2006
32
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Troubleshooting Techniques
Problem: Bill Validator Errors
1. Verify that the bill stacker is installed correctly inside the bill validator. 2. Verify that the bill validator head is seated firmly in the validator housing. 3. Verify that the proper bill validator EPROM is installed.
From the Operator Menu, select MACHINE TEST and then the VALIDATOR TEST option. If the bill validator has been enabled, the IDLE message appears on the game alphanumeric display. If it is disabled, the message OFF-LINE is displayed. If the OFF-LINE message appears, select the CONFIGURATION and then BILL VALIDATOR options from the Operator Menu. A value of 0 on the Winner Paid meter indicates that the validator is not enabled. Press SPIN REELS, or the appropriate button, to toggle the value to 1 to enable it.
NOTE:
On-screen button labels change depending upon selections chosen during the Birth procedure. Active buttons appear illuminated or flashing. Refer to the appropriate EPROM Description Sheet (EDS) for proper Game and Key Panel type settings.
Press BET ONE to view the status of each of the following options on the Winner Paid meter (0 = disabled, 1 = enabled).
4. From the Operator Menu, select MACHINE TEST and then the VALIDATOR TEST option to test the bill validator. Insert bills of various denominations into the validator. Good bills are drawn in and Escrow appears briefly on the alphanumeric display. Bad bills are rejected and the reason for rejection is displayed. 5. Verify that the main wire harness is plugged into connectors J10 and J26 on the backplane board. 6. Verify that the main wire harness is plugged into the connector on the back of the bill validator. 7. Substitute a known good bill validator head.
20 Jan 2006
33
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
20 Jan 2006
34
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
20 Jan 2006
35
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Appendix A
Parts Lists* and Exploded View Drawings
20 Jan 2006
36
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Cabinet 1
Figure 27 Cabinet 1 Power Supply, Hopper and Bracket Installations Table 8 Part Number List for Hopper and Power Supply Item 1 2 3 Part Number Description 09-12094 SCX Cabinet 07-41103 Two-Plex Electrical Box 07-41051 Hopper, UV19U32TS $1.00 07-41080 Hopper, UV19U32TS $0.50 07-41050 Hopper, UV19U32TS $0.25 MD Bowl 07-41049 Hopper, UV19U32TS $0.05 Contact ATI Sales Representative for denomination conversion parts. 4 1 04-12009 Hopper Bracket 5 1 O4-12011 Switch Bracket 6 1 07-10106 Sound Board *7 1 07-40162 Meter Assembly* 8 1 06-20074 Power Supply, 5V, 12V, 24V *Part numbers and availability subject to change. Qty 1 1 1
20 Jan 2006
37
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Table 9 *Meter Assembly (07-40162) Parts Breakdown Item 4 1 5 1 8 2 1 Qty Part Number 01-80064 Meters, 7-Digit, 24VDC 02-10116 Connector, Closed End, 16-10 AWG 02-50002 Pin, Male .062, Molex 02-50035 Conn, 9-PIN .062, Plug, Free-Hanging 03-11001 Screw, PH PM, SEM, 4-40x1/4 03-20022 Nut, K-LOC 6-32 03-71005 Label, UR, Meter, Coin Drop 03-70164 Laminate, 6 Mil Scuf 03-72029 Adhesive, TT-400 1 03-71006 Label, UR, Meter, Coin In 03-70164 Laminate, 6 Mil Scuf 03-72029 Adhesive, TT-400 1 03-71007 Label, UR, Meter, Coin Out 03-70164 Laminate, 6 Mil Scuf 03-72029 Adhesive, TT-400 1 03-71065 Label, Meter, Jackpot 03-70164 Laminate, 6 Mil Scuf 03-72029 Adhesive, TT-400 1 04-12010 Bracket, Center Meter, US32TS *Part numbers and availability subject to change.
20 Jan 2006
38
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Cabinet 2
Figure 28 Cabinet 2 Handle Mechanism and WBA Bill Validator Components Table 10 Handle and Bill Validator Part Numbers Item Qty Part Number 1 1 09-12094 2 1 09-12016 3 1 03-70118 4 1 04-41075 5 1 07-41115 6 1 07-40155 7 1 04-41030 8 1 09-12046 9 1 04-12081 *Part numbers and availability subject to change. Description SCX Cabinet Pull Handle Cover Pull Handle with Knob Coin Chute Handle Mech. WBA Bill Validator (WBA13) WBA Bill Validator Bezel Bill Stacker Door Bill Validator Housing
20 Jan 2006
39
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Figure 29 Reel Shelf Assembly Exploded View Table 11 Reel Shelf Assembly Parts List Item 1 2 3 Qty Part Number 1 09-12094 1 07-10106 1 07-41422 1 02-60001 2 04-40029 4 1 07-10167 5 1 09-12029 6 1 07-41423 2 01-80013 1 01-80032 1 01-80042 1 01-80049 2 01-80170 1 02-70015 1 04-13906 1 07-20558 1 09-12072 7 1 04-13915 *8 5 07-41421 9 1 07-10168 *Part numbers and availability subject to change. Description SCX Cabinet Sound Board Assembly, CPU Cage Switch, Cherry E79-30A Guide, CPU Board PCB VIG-520 Main Door CPU Assembly, Reel Shelf Fuse Holder,5mm x 20mm Fuse Holder,L/F# 3453LF2 Receptacle,A/C 689-4086 Fuse,6 AMP,3AG,L/F#312006 Fuse,2.5A,GMA Switch, ON/OFF Shelf, Main Reel Harn,US0320TS,AC Cover,UV/B19/D,Wire,Shelf BRKT, 5 Reel Adapter ATI ASSY, Reel Mech 2 Back Lit Board, Backplane VIG-520
20 Jan 2006
40
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Table 12 *5-Reel Assembly (07-41421) Parts Breakdown Item Qty Part Number 1 1 01-80063 2 3 01-70038 3 3 03-11024 4 4 03-11087 5 4 03-11088 6 1 03-30034 7 4 03-41059 8 2 03-50003 9 1 03-50012 10 4 03-60015 11 1 03-70093 12 1 04-12075 13 1 04-31048 14 1 04-13918 15 1 04-40380 16 1 04-31048 17 1 07-10153 18 1 07-20567 19 1 07-20992 *Part numbers and availability subject to change. Description Motor, 24V LED, Reel Back Lite Screw, FH 4-40x3/8 Screw, PH M3x8MM NYL Screw, PH M4x12MM Washer, Reel Mech Spacer, 5/16x5/16 NYL Cable Tie, 4-inch Cable Tie Mount O-Ring, Reel Mech Clip, E Retaining Bracket, Reel Mech Shadow Box, Starpoint Bracket, Shadow Box Mount Reel Plastic, Starpoint 2-inch Window, Starpoint Shadow Box PCB, Reel Driver Harness, Meter Sensor Harness, Back Lite
20 Jan 2006
41
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Figure 30 Reel Assembly - Exploded view Table 13 Reel Assembly Parts List Item 1 2 3 Qty Part Number 1 01-80063 1 04-12075 1 04-31048 3 01-70038 4 1 04-13918 5 1 04-40380 6 1 07-10153 7 1 07-20567 8 1 07-20992 *Part numbers and availability subject to change. Description Motor, 24V Bracket, Reel Mech Shadow Box, Starpoint LED, Reel Back Lite Bracket, Shadow Box Mount Reel Plastic, Starpoint 2-inch PCB, Reel Driver Harness, Meter Sensor Harness, Back Lite
20 Jan 2006
42
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Figure 31 Main Door Assembly Table 14 Main Door Parts List Glass and Lights Item 1 2 Qty Part Number 1 07-41424 1 (game specific) 1 07-20730 3 1 07-20729 4* 1 07-41062 5 1 09-12040 6 1 04-13862 1 04-40392 7 1 01-80047 8 1 07-10246 9 1 04-22027 10 1 04-21282 11 1 07-10245 *Part numbers and availability subject to change. Description Main Door Assembly Reel Glass Lanyard Chain Main Door, 15-inch Lanyard Chain Belly Door, 12-inch Assembly, UV19/032 LMP.LWR Belly Door, UV19/S/D BL BX ACC. Bracket, USO32TS Upper Glass Fluorescent Lamp Filter Bulb, Fluores F15T8/CW18 7 Segment Display Bracket, LED Counter/Meter Gasket Horizontal LED PCB
20 Jan 2006
43
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Figure 32 Door Hardware Exploded View Table 15 Main Door Parts List Brackets and Backplates Item 1 Qty Part Number 1 07-41424 1 04-21013 1 04-21035 2 1 04-21071 1 04-21003 1 04-21041 3 1 04-31009 4 1 09-12052 5 1 04-12032 6 1 04-12031 7 1 09-12034 8 1 04-12045 9 1 04-40108 10 1 03-80123 11 1 03-70027 *Part numbers and availability subject to change. Description Main Door Backplate, Coin Head $.05 Backplate, Coin Head $.25 Backplate, Coin Head $.50 Backplate, Coin Head $1.00 Backplate Token Head Coin Head, SLT/US32/UB20, 20 DEG Cover, Coin Exit Bracket, Solenoid Bracket, U19/U20/U32 Diverter Diverter, UV19/UB20/US Bracket, UV19/UB20 Coin Mech. Guide, Coin US/UV19/UB20 Lockbar, Main Door SCX TS Hinge, SCX Main Door
20 Jan 2006
44
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Figure 33 Main Door Brackets, Buttons, Bezels, and Bushing Table 16 Main Door Assembly Parts List Brackets, Buttons, Bezels, and Bushing Item 1 2 3 Qty Part Number 1 09-11225 1 04-12040 1 03-70086 2 01-80151 4 2 04-12113 5 1 03-70085 6 1 02-70064 7 1 03-80102 8 1 03-70081 9 1 04-40109 10 1 04-12043 11 1 Reference *Part numbers and availability subject to change. Description Main Door Weldment Bracket, Slide, Access Door Spring, Extension, Access Door Speaker, 8 OHM, 6 WATT Bracket, SPKR.MNT.Door Ring, Retainer Button, Push, Access Door Bushing, Push Button Hinge, Access Door Guide, Bezel, Main Door Bracket, Lamp Door, Belly, Assembly
20 Jan 2006
45
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Figure 34 Main Door Belly Components Table 17 Main Door Belly Parts List Item 1 2 3 Qty Part Number 1 07-41424 1 04-41013 2 01-80037 2 01-80036 4 2 01-80043 5 1 04-12048 6 1 04-41031 7 1 04-41033 *Part numbers and availability subject to change. Description Main Door Reject Chute Ballasts, Lamp, -22W, 120V Starters Lamp, FS-2 Socket, Starter, #596 Bracket, UV19, Belly Coin Handling Coin Hopper Chute Drop Chute
20 Jan 2006
46
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Belly Door
Figure 35 Belly Glass Assembly Table 18 Belly Parts List Item Qty Part Number 1 1 XX-XXXX 2 1 09-12160 3 1 04-12039 4 1 01-80047 *Part numbers and availability subject to change. Description Game specific, contact ATI Sales Dept. Door, Belly Bracket, Lamp, Glass Bill AC DR Lamp, Fluorescent F15T8/CW
20 Jan 2006
47
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Buttons
Figure 36 Deck Buttons Table 19 6-Button Deck Panel Parts List Item Qty Legend Part Number 1 1 04-40190 02-70121 2 1 04-40188 02-70140 3 1 04-40189 02-70121 4 1 04-40221 02-70131 5 1 04-40268 02-70120 6 1 04-40222 02-70120 *Part numbers and availability subject to change. Description S/S Collect Change Bet One Bonus Spin Spin Reels (Vert. Rectangle.) Max Bet (Vert. Rectangle)
20 Jan 2006
48
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Figure 37 10-Button Deck Table 20 10-Button Panel Assembly Parts List (07-41427) Item 1 Qty Part Number 1 565078-1 1 15545 1 51713 2 1 02-70140 3 1 02-70121 4 1 02-70121 5 1 02-70121 6 1 02-70121 7 1 02-70121 8 1 02-70121 9 1 02-70121 10 1 02-70121 11 1 02-70121 *Part numbers and availability subject to change. Description Button Blank Channel Fixing M5 Nut Button 1 - Change Button 2 - Collect Button 4 - Game Specific Legend Button 5 - Game Specific Legend Button 6 - Game Specific Legend Button 9 - Game Specific Legend Button 10 - Game Specific Legend Button 11 - Game Specific Legend Button 14 - Game Specific Legend Button 15 - Game Specific Legend
20 Jan 2006
49
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Figure 38 11-Button Deck Table 21 11-Button Deck Parts List Item Qty Part Number 1 1 02-70121 2 1 02-70140 3 1 02-70121 4 1 02-70121 5 1 02-70121 6 1 02-70121 7 1 02-70121 8 1 02-70121 9 1 02-70121 10 1 02-70121 11 1 02-70121 *Part numbers and availability subject to change. Description Button 0 Collect Button 1 Change Button 2 - Game Specific Legend Button 4 - Game Specific Legend Button 5 - Game Specific Legend Button 6 - Game Specific Legend Button 9 - Game Specific Legend Button 10 - Game Specific Legend Button 11 - Game Specific Legend Button 14 - Game Specific Legend Button 15 - Game Specific Legend
20 Jan 2006
50
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
Coin Acceptor
Figure 39 Coin Acceptor Mounting Table 22 Coin Acceptor Mounting Parts List Item Qty Part Number 1 01-80031 1 1 04-12032 2 1 04-12031 1 04-12045 3 2 03-70110 4 1 (property specific) 5 1 09-12034 6 1 03-80011 7 1 03-70025 *Part numbers and availability subject to change. Description Solenoid, Diverter #11DC, 24V Bracket, UV19/UB20 Solenoid Bracket, UV19/UB20/US32 Diverter Bracket, UV19/UB20 Coin Mech. Spring Coin Diverter #LE0118C-4 Coin Acceptor Diverter, UV19/UB20/US Roll Pin, Diverter 3/32X5/8 Spring, Solenoid, N#55084-00
20 Jan 2006
51
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
1. Open the main door. 2. Turn OFF the AC power. 3. Lift up on the bottom edge of the reader/keypad/display bracket or blank panel at the notches provided on the top edge of the doorframe as shown below.
4. When the card reader/keypad/display bracket or blank panel is free of the groove in the doorframe, pull the bracket and tray forward until the cable connectors on the keypad, card reader, and display are accessible. 5. Unplug the power supply. 6. Disconnect the cables from the bracket components, and then remove the bracket and tray.
To remove glass once the PMM tray is opened:
1. Lift the glass up and swing the bottom of the glass free of the glass tabs. 2. Pull glass down toward the PMM tray until the top is free of the channel and carefully remove the glass.
20 Jan 2006
52
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
20 Jan 2006
53
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.
User Response
Errors, omissions, or suggestions for improvement to this manual should be reported to: Aristocrat Technologies, Inc. 7230 Amigo Street Las Vegas, Nevada 89119 Attn: Technical Publications Department Tel: (800) 748-4156 Fax: (702) 270-1136 Please rate this manual: Excellent Adequate Needs Improvement Suggestions for improvement:
20 Jan 2006
54
This document contains confidential information that is proprietary to ATI. It may not be copied or disclosed to unauthorized parties. 2006 Aristocrat Technologies, Inc. All rights reserved.