Professional Documents
Culture Documents
ML-1440
SERVICE
LASER PRINTER
Manual
CONTENTS
1. Precautions 2. Specifications 3. Disassembly and Reassembly 4. Troubleshooting 5. Exploded Views and Parts List 6. Block Diagram 7. Connection Diagram
This service manual is also provided on the web, the ITSELF system f Samsung Electronics Co., Ltd. http://itself.sec.samsung.co.kr
Samsung Electronics Co.,Ltd. JUNE 2002 Printed in Korea. VERSION NO. : 1.02 CODE : JC-0066A
Repair Manual
SAMSUNG LASER PRINTER
ML-1450Series
ML-1440
CONTENTS
1. Block Diagram 2. Connection Diagram 3. Schematic Diagrams
Electronics
SAMSUNG
This manual is made and described centering around circuit diagram and circuit description needed in the repair center in the form of appendix.
Samsung Electronics Digital Printing CS Group
Copyright (c) 2002. 1
SPGPe (KS32C61100)
Sys Cntl BUS Sys Addr BUS Sys Data BUS
PLL
POWER ON RESET
/CS,/RD ,/W R CPU DATA BUS CPU ADDR. BUS
1. Block Diagram
Samsung Electronics
SYSTEM DATA BUS SYSTEM ADDR. BUS MA MD RAS CAS EDO / FPM DRAM Control (4Bank) GEU
A/D Bu s
RCS RD WR
IOCS
G PIO
PANEL INTERCACE MOTOR CONTROL NV RAM INTERCACE I /O INTERFACE SENSORS INPUT SOLENOID CONTROL 74HC245*2EA FAN/PTL CONTROL 74LS273*3EA LSU INTERFACE HVPS CONTROL
Tone Generator
UA RT ( 3 CH)
DMAC (2 CH)
PARALLEL INTERFACE
VIS
JB IG
5V
BLOCK DIAGRAM
Repair Manual
SMPS
24V
1-1
CONNECTION DIAGRAM
2. Connection Diagram
HVPS
PTL
Ther mistor
T herm1 T herm2 DCU (For Sys t em Tes t ) 1234CN1 2 CN1 3 5V RXD TX D GND- 5V CN1 0 PT L Ct rl 5V CN3 CN1
1- 24V S
2- GN D _2 4
CN2
CN1 4 Solenoid
3- 5V
CN1
4- GND _5 V
5- T H V _PWM
MP Tray (Option)
CN2
10- PT L
11- N .C.
SMPS
CN5 1- Sav e 2- P_Nar r ow 3- Empt y 4- Feed 5- FA N 6- Clut ch 7- Fus er 8- MP_Clut c h 9- MP_Empt y 10- Mot or _PA 11- Mot or _PB 12- / Mot or _PA 13- / Mot or _PB 14- SCF_Cass ete 15- SCF_Mot or 16- SCF_Clut ch 17- SCF_Empt y 18- N.C. 19- T herm2 20- T herm1 21- 5V 22- EXT _Clo ck 23,2 4- 5V 25- 5V PS 26,2 7,28- GND_5 V
1- 5V
2- SC F_Sel C as set t e
12- N .C.
3- SCF_Mot or 4- SCF_CL UT CH
5- SC F_Empt y 6- 24V S
CN2
Exit Sensor
( For L SU 5 V S Cut )
1 - 5V 2 - Ex it _s ignal 3 - GND_5 1 - 5V 2 - 5V S 123456/ HSYNC 5V S GND_5 / LD_ON / VDO LSUPOWE R1 200 7- 24V S 8- GND_2 4 9- P_MOT OR 10- / LREA DY 11- EXT _CL K 123456785V GND_5 LED1 LED2 LED3 LED4 Key 1 Key 2
7,8- GND_5
SCF (Option)
Micro- Switch
CN1 1
Controller
CN6 CN3
CN3 CN8
1234-
Motor
Heat Lamp (Fuser)
LSU
CN5 02
CN5 01
Power Switch
CN5 03
DC FAN
Panel B'd
HOST
(PC)
CN5
CN4
28- A 15, 29 - D 19, 3 0- A 14, 31- D 18, 32- A13 , 33- D 17, 34 - A 12, 3 5- D 16, 36- A 11, 37- A6,
38- A 10, 39 - / RESET , 4 0- A 9, 4 1- / WA IT , 42 - A 8, 43- / IOCS3, 44 - A 7, 45 - / IOCS3, 4 6- N .C ., 47- N .C., 48- GN D5 , 49- A1 8, 50- / RD, 51- /WE, 5 2- GN D 5,
53- N .C., 54- N .C., 55 - / EIRQ1, 56- GN D 5, 5 7- N .C ., 58- 5V , 59 - 5V , 60 - 5V (60 pi n Connec t or)
2-1
SCHEMATIC DIAGRAMS
3. Schematic Diagrams
3-1 Main Circuit Diagram (1/6)
3-1
SCHEMATIC DIAGRAMS
3-2
SCHEMATIC DIAGRAMS
3-3
SCHEMATIC DIAGRAMS
3-4
SCHEMATIC DIAGRAMS
3-5
SCHEMATIC DIAGRAMS
3-6
SCHEMATIC DIAGRAMS
3-7
SCHEMATIC DIAGRAMS
3-8
SCHEMATIC DIAGRAMS
3-9
Block Diagram
6. Block Diagram
Controller
L D33C 3.3V Regulat or OSC. 53.0109277M H z FS781 Fr eq. A t t n. X- T A L 10M H z XC61FN 3112M R V olt age Det ect or L D25C 2.5V Regulat or K 4S641632D- T C75 SDRA M 64M bit 29F800- 70 Flash M em or y
Engine/ SM PS
N ar r ow Sensor M ain- Clut ch A 2918SWV M ot or Dr iv er
M otor
74H C4060 Ripple Count er L M 393 Com par at or Feed Sensor Em pt y Sensor
ASIC S3 C4 6 M 0 X 0 1
512K bit * 16bit L C245 3st at e T r ansceiv er 74A CT 245 3st at e T r ansceiv er
L CX273 Oc t al D- F/ F
PA CS1284 P1284 N et w or k
5V
93C66 EEPROM - 5V
SM PS
24V
H eat Lamp
IEEE1 2 84
U SB Ex it Sensor
PC
Panel
L SU
H V PS
Inlet Ass'y
Pow er Cord
Samsung Electronics
6-1
Block Diagram
6. Block Diagram
Controller
L D33C 3.3V Regulat or OSC. 53.0109277M H z FS781 Fr eq. A t t n. X- T A L 10M H z XC61FN 3112M R V olt age Det ect or L D25C 2.5V Regulat or K 4S641632D- T C75 SDRA M 64M bit 29F800- 70 Flash M em or y
Engine/ SM PS
N ar r ow Sensor M ain- Clut ch A 2918SWV M ot or Dr iv er
M otor
74H C4060 Ripple Count er L M 393 Com par at or Feed Sensor Em pt y Sensor
ASIC S3 C4 6 M 0 X 0 1
512K bit * 16bit L C245 3st at e T r ansceiv er 74A CT 245 3st at e T r ansceiv er
L CX273 Oc t al D- F/ F
PA CS1284 P1284 N et w or k
5V
93C66 EEPROM - 5V
SM PS
24V
H eat Lamp
IEEE1 2 84
U SB Ex it Sensor
PC
Panel
L SU
H V PS
Inlet Ass'y
Pow er Cord
Samsung Electronics
6-1
5-1 Main Assembly Exploded view ................................................................................................................ page(5-2) 5-2 Top Assembly Exploded view .................................................................................................................. page(5-4) 5-3 Frame Assembly Exploded view ............................................................................................................. page(5-6) 5-4 Exit Assembly Exploded view .................................................................................................................. page(5-9) 5-5 Fuser Assembly Exploded view ............................................................................................................. page(5-11) 5-6 Rack-MPF Assembly Exploded view .................................................................................................... page(5-13) 5-7 Drive Assembly Exploded view .............................................................................................................. page(5-15) 5-8 Pick-Up Assembly Exploded view ......................................................................................................... page(5-17) 5-9 Cassette Assembly Exploded view ....................................................................................................... page(5-19)
Samsung Electronics
5-1
16 2
19 15 3 4 20 9 5 22
22-1 22-1
18 7 14 13 8 17 25
21 12 11 26 10
26-5
SA MS UN G
26-4 26-7
26-2
23
24
5-2
Samsung Electronics
DESCRIPTION ELA HOU-COVER MAIN UNIT-LSU ELA UNIT-MOTOR 14 ELA UNIT-DEVE MEA RACK-MPF MEA UNIT-FEED CAT 270 CBF-HARNESS-MOTOR MEA UNIT-FEEDER CBF-HARNESS-ENG-SCF IPR-SHIELD PCU PCT-INSULATOR PCU PBA MAIN-ENGINE_V1(110V) PBA MAIN-ENGINE_V2(220V) ELA UNIT-FRAME BASE ELA UNIT-FRAME BASE PBA MAIN CTRL-LOW ELA UNIT-FUSER ELA UNIT-FUSER CBF HARNESS-LSU SMPS-HVPS MEA RACK-HOU EXIT PMO-DUCT FAN PMO-DUMMY FACE MAIN(L) PMO-DUMMY FACE MAIN(R) UNIT SENSOR MANUAL PMO-CAP SENSOR PBA SUB-MANUAL SENSOR ELA HOU-SCF MEA RACK-SCST, SCF PMO-COVER CONTROLLER MEA UNIT-MP TRAY PMO-COVER MP NPR-BADGE BRAND PMO-TRAY EXTENTION MP PMO-TRAY HOLDER MP IPR-GUIDE LATCH PMO-SIDE GUIDE MP PMO-TRAY LINK MP
SEC CODE See Page 5-5 JC59-00004A JC96-02058A * JC97-01345A JC97-01467A * JC97-01324A JC39-00154A JC70-00080A JC72-00334A JC92-01409A JC92-01410A JC96-01641M JC96-01641L JC92-01392A JC81-00395B JC81-00395A * JC44-00040A JC97-01338L JC72-00582A * * JC96-01814A * * * * JC72-00358A JC97-01325A * * * * * * *
QTY 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2
SA O O O X O O X O O O O O O O O O O O X O O O X X O X X X X O O X X X X X X X
REMARK
Optional Optional
Samsung Electronics
5-3
11
10 2
12 3 13 9 4
5 7 6 8
5-4
Samsung Electronics
NO 0 1 2 3 4 5 6 7 8 9 10 11 12 13 S1
DESCRIPTION ELA HOU-COVER MAIN PMO-COVER OPEN COVER-MAIN 1440 PMO-CAP REAR PMO-STOPPER HINGE OPEN PMO-LENS LED PMO-KEY BUTTON PMO-KEY SAVE MODE PBA SUB-PANEL_II PMO-SUPPORT MAIN PMO-STOPPER_EXIT,P PMO-COVER REAR PMO-STACKER REAR IPR-SPRING LOCKER REAR SCREW-TAPTITE
QTY 1 1 1 1 2 1 1 1 1 1 1 1 1 2 6
SA O X X X X X X X X X X X X X X
REMARK
Samsung Electronics
5-5
15-1 15-2
15 2
15-3
44
19-2
19
19-1
46 45
3
47 48 47
1
46
17 16
3 38 20
39
45
21
18-1 18-2
14 13 11
22-1
18 8 5
34
22-2
22
22-3 22-4
10 36 51 30
30-1
42 9 49
49-3 30-3 49-2 49-1
43 23
50 35 32
32-2 32-1 28-2 28-1
24-1 24-2
31-1
24 33 28 27 26
25-1 25-2
31
29-1 29-2
25 41
29-3
29-4
29 4
5-6
Samsung Electronics
NO 0 1 2 3 4 5 6 7 8 9 10 11 13 14 15 15-1 15-2 15-3 16 16-1 16-2 16-3 16-4 17 18 18-1 18-2 19 19-1 19-2 20 21 22 22-1 22-2 22-3 23 24 24-1 24-2 25 25-1
DESCRIPTION ELA UNIT-FRAME BASE ELA UNIT-FRAME BASE FAN-DC-HAWK PMO-GUIDE RIB CBF HARNESS-INLET ASSY PMO-HOLDER WIRE KEY DEVE GEAR-EXIT /U ID CBF-HARNESS_FUSER PBA SUB-EXIT SENSOR CBF-HARNESS-THERMISTOR JOINT CBF-HARNESS-MP_CLUTCH ENG PBA SUB-FUSER SW PMO-FRAME COVER IPR-TERMINAL FU ELA-UNIT-HOLDER TR L PMO-BUSHING TR SPRING TR L PMO-TRANSFER HOLDER ELA-UNIT-HOLDER TR R PMO-BUSHING TR SPRING TR R PMO-TRANSFER HOLDER IPR-PLATE TR GEAR-TR 29 ELA UNIT-GUIDE DEVE L PMO-GUIDE DEVE L SPRING GUIDE DEVE ELA UNIT-GUIDE DEVE R PMO-GUIDE DEVE R SPRING GUIDE DEVE ELA HOU-VARISTOR IPR-TERMINAL TR ELA UNIT-SENSOR DEVE PBA SUB-SWITCH PMO-HOLDER ACTUATOR PMO-ACTUATOR DEVE GROUND FU ELA UNIT-TERMINAL TR S ICT-SHAFT HV LARGE SPRING-HV LARGE ELA UNIT-TERMINAL TR L ICT-SHAFT HV LARGE
SEC CODE JC96-01641M JC96-01641L JC31-00004A * * * * * * * * * JC92-01261B * * JC96-01730A * * * JC96-01729A * * * * JC66-00039A * * * * * * JC96-01772A * * * * * * * * * * *
QTY 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 3 3 1 1
SA O O O X X X X X X X X X O X X O X X X O X X X X O X X X X X X O X X X X X X X X X X X 110V 220V
REMARK
Samsung Electronics
5-7
NO 25-2 26 27 28 28-1 28-2 29 29-1 29-2 29-3 29-4 30 30-1 30-2 30-3 31 31-1 31-2 31-3 32 32-1 32-2 33 34 35 36 37 38 39 41 42 43 44 45 46 47 48 49 49-1 49-2 49-3 50 51
DESCRIPTION SPRING-HV SMALL GROUND-HVPS IPR-REMOVE KEY ELA UNIT-ACTUATOR FEED PMO-ACTUATOR FEED PMO-HOLDER ACTUATOR ELA UNIT-GUIDE TRANSFER PMO-HADER SAW PLATE IPR-PLATE SAW IPR-GUIDE TRANSFER PMO-GUIDE RIB TR ELA UNIT-GUIDE FEED HAWK16 PMO-GUIDE OPTIC GUIDE FEED PMO-HOLDER G/PAPER ELA UNIT-PTL GUIDE PLATE FEED PMO-HOLDER PTL PBA SUB-PTL ELA UNIT-EMPTY ACT PMO-ACTUATOR EMPTY HAWK SPRING EMPTY PMO-HINGE GUIDE FEED IPR-GND ICU 2 PMO-CAP SENSOR GND MP GEAR P/UP DRV GROUND MOTOR IPR-GUIDE DUST IPR-OPC-HAWK CAP CONNECTOR L CAP CONNECTOR U MEC-ROLLER TRANSFER GEAR IDLE Z27 RING-CS WASHER-PLAIN IPR-WASHER SPRING SU ELA UNIT-ACTUATOR FEED HAWK14 PMO-ACTUATOR FEED PMO-HOLDER ACTUATOR SPRING ETC-FEED HAWK14 PMO-GUIDE_SKEW(12) IPR-TERMINAL TR HAWK
QTY 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1
SA X X O X X X X X X X X O X X X X X X X X X X O O X X O X X X X X O X X X X X X X X X X
REMARK
5-8
Samsung Electronics
S1
S1
16
13 14
S1
11 9 17
S1 10 4 3 7 8
6 2 5
Samsung Electronics
5-9
NO 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 S1
DESCRIPTION MEA RACK-HOU EXIT PMO-FRAME REAR GEAR-EXIT/U, ID RING-CS GEAR-IDLE 25 SPRING-F/DOWN PMO-HOLDER EXIT_F/DOWN PMO-ROLLER-EXIT, MAIN PMO-ROLLER-EXIT, FR MEC-BEARING, EXIT RING-C MEA UNIT-ROLL EXIT GEAR-EXIT MEC-BEARING, EXIT RING-C HOLDER LEVER LEVER STACKING GUIDE EXIT RING-C SCREW TAPTITE
QTY 1 1 1 2 1 4 4 4 4 2 1 1 2 2 2 1 2 4
SA O X X X X X X X X X X X X X X X X X
REMARK
5-10
Samsung Electronics
2 4 37 7
10 12 1 12 3
36
1 6
11
9 13
1 14 16 17 31 29 30 34 20 19 27 26 35 33 32 15
28
23 24 21 18
38 25 22
Samsung Electronics
5-11
NO 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
DESCRIPTION AS-FUSER ASSY AS-FUSER ASSY SCREW TAPTITE M3 x 8, BH+ SCREW TAPTITE M3 x 10, FH+ SCREW MACHINE M3 x 6 THERMISTOR-FUSER ELECTRODE FU R ELECTRODE FU M ELECTRODE FU L THERMOSTAT BRKT GEAR FUSER GEAR-IDLE 25 GEAR-IDLE 15 RING-CS COVER FUSER ROLLER EXIT_F/UP EXIT_F/UP (SPRING) SPRING-CLAW GUIDE-CLAW LAMP-HALOGEN LAMP-HALOGEN NEX-ROLLER-HEAT MEC-ROLLER PRESSURE FRAME FUSER PMO-GUIDE INPUT GEAR FUSER, Z32 BUSHING HR-L BUSHING HR-R SPRING-BEARING PR BUSHING PR GUIDE REAR SHAFT EXIT_F/UP BUSHING_TX GEAR-EXIT RUBBER EXIT RUBBER EXIT F/UP ACTUATOR EXIT SPRING-ACTUATOR HOLDER BRUSH BRUSH ANTISTATIC HOLDER SHAFT
QTY 1 1 10 1 2 1 1 1 1 1 1 1 1 2 1 3 3 4 4 1 1 1 1 1 1 1 1 1 2 2 1 1 3 1 3 1 1 1 1 1 1
SA O O X X X O X X X X X X X X X X X X X O O O O X x X X X X X X X X X X X X X X X X
110V 220V
5-12
Samsung Electronics
NO 0 1 2 3 4
QTY 1 1 1 1 1
SA O X X X X
REMARK
Samsung Electronics
5-13
2 16
11
10
12 4
15
16 14
13
5-14
Samsung Electronics
NO 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
DESCRIPTION ELA UNIT-MOTOR 14 MOTOR-STEP IPR-BRKT GEAR IPR-BRKT MOTOR GEAR-RDCN 145-70 GEAR-RDCN 90-24 GEAR-OPC DRV 135 GEAR-OPC DRIVE2 GEAR-FEED DRV GEAR-CLUTCH 56 GEAR-FUSER DRV23 PMO-CLUTCH LEVER SPRING-CLUTCH WASHER-PLAIN MPR-POLYWASHER 8 WASHER-PLAIN SCREW-MACHINE
QTY 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 5
SA O O X X X X X X X X X X X X X X X
REMARK
Samsung Electronics
5-15
0 8 2 5 11 24 25 7 2 5 9
21 26 6
2 14 23
12
18 2 13 5 15 3 19 10 1 15 22 4 20 17 16 10
5-16
Samsung Electronics
NO 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
DESCRIPTION MEA UNIT-FEEDER SCREW-TAPTITE WASHER-PLAIN SPRING-FEED(1) SPRING-FEED(2) BEARING-PICK UP GEAR-P/UP DRIVE GEAR-FEED GEAR-PICK UP(12) IPR-SHAFT FEED IPR-SHAFT FEED IDLER IPR-SHAFT PICK UP GROUND_FEED IPR-GUIDE_FEED PMO-HOUSING P/UP PMO-ROLLER FEED L PMO-ROLLER FEED S PMO-SUB HOLDER FEED PMO-FRAME_FEED PMO-HOLDER FEED(1) PMO-HOLDER FEED(2) PMO-IDLE PICK_UP PMO-ROLL_FEED, DRV 12 RMO-RUBBER PICK_UP RMO-LEVER PICK_UP SPRING PICK UP(12) RING-CS
QTY 1 1 4 1 1 4 1 1 1 1 3 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1
SA O X X X X X X X X X X X X X X X X X X X X X X X X X X
REMARK
Samsung Electronics
5-17
17 16 15 18 9 8
14 13 12 11 10
1 2 7 6 19 3 5 4
5-18
Samsung Electronics
NO 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
DESCRIPTION MEA UNIT-FEEDER CAT 270 PMO-FRAME CASSETTE PMO-GUIDE INNER,CAST PMO-GUIDE CASSETTE P PMO-HOLDER INDICATOR PMO-INDICATOR EMPTY PMO-LOCKER PLATE SPRING LOCKER PLATE PMO-FRAME LEGAL LABEL(R)-PLATE PMO-REAR GUIDE CST IPR-GUIDE PAPER LABEL(R)-HEIGHT IPR-FINGER PMO-SIDE GUIDE SPRING-KNOCK UP IPR-NOCK UP PLATE PAD KNOCK UP GUIDE-PLATE SCREW
QTY 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 2 2 1 1 3
SA O X X X X X X X X X X X X X X X X X X X
Samsung Electronics
5-19
Troubleshooting
4. Troubleshooting
4-1 How to use DCU 4-1-1 DCU Setup ......................................Page(4-2) 4-1-2 Code ................................................Page(4-2) 4-1-3 Self Diagnostic Mode......................Page(4-3) 4-1-4 Self Test Button ................................Page(4-4) 4-1-5 Paper Path Layout ...........................Page(4-4) 4-1-6 DCU Panel .......................................Page(4-5) 4-2 The cause and solution of Bad image 4-2-1 Vertical Black Line and Band ..........Page(4-6) 4-2-2 Vertical White Line ...........................Page(4-6) 4-2-3 Horizontal Black Band .....................Page(4-7) 4-2-4 Black/White Spot..............................Page(4-7) 4-2-5 Light Image.......................................Page(4-8) 4-2-6 Dark Image or a Black.....................Page(4-8) 4-2-7 Uneven Density................................Page(4-9) 4-2-8 Background ......................................Page(4-9) 4-2-9 Ghost (1)...........................................Page(4-10) 4-2-10 Ghost (2)..........................................Page(4-10) 4-2-11 Ghost (3) ..........................................Page(4-11) 4-2-12 Ghost (4) .........................................Page(4-11) 4-2-13 Satins on the Face of Page............Page(4-11) 4-2-14 Satins on Back of Page..................Page(4-12) 4-2-15 Blank Page Print out (1) .................Page(4-12) 4-2-16 Blank Page Print out (2) .................Page(4-12) 4-6 The cause and solutions of bad environment of the software 4-6-1 The printer is not working (1)...........Page(4-26) 4-3 The cause and solution of the bad discharge 4-3-1 Wrong Print Position .......................Page(4-13) 4-3-2 JAM 0...............................................Page(4-13) 4-3-3 JAM 1...............................................Page(4-14) 4-3-4 JAM 2...............................................Page(4-14) 4-3-5 Multi-Feeding...................................Page(4-15) 4-3-6 Paper rolled in the fuser .................Page(4-15) 4-3-7 OPC .................................................Page(4-16) 4-6-2 The printer is not working (2) .........Page(4-27) 4-6-3 Abnormal Printing.............................Page(4-28) 4-6-4 SPOOL Error ...................................Page(4-29) 4-5 Toner Cartridge Service 4-5-1 Precautions on Safe-keeping of Toner Cartridge ..........................................................Page(4-22) 4-5-2 Service for the Life of Toner Cartridge ..........................................................Page(4-22) 4-5-3 Service for Judgement of Inferior Expendables and the Standard of Guarantee .....Page(4-22) 4-5-4 Signs and Measures at Poor toner cartridge ..........................................................Page(4-23) 4-4 The cause and solution of the malfunction 4-4-1 All LEDs blinking (Fuser Error)........Page(4-17) 4-4-2 All LEDs blinking (SCAN ERROR) .Page(4-17) 4-4-3 Not function of the gear of the fuser due to melting away.....................................Page(4-18) 4-4-4 Paper Empty.....................................Page(4-18) 4-4-5 Paper Empty without indication.......Page(4-18) 4-4-6 Cover Open ......................................Page(4-19) 4-4-7 No lamp on when the cover is open ...........................................................Page(4-19) 4-4-8 Defective motor operation ...............Page(4-20) 4-4-9 No Power..........................................Page(4-20) 4-4-10 Vertical Line Getting Curved .........Page(4-21)
Samsung Electronics
4-1
Troubleshooting
4-1-2 Code
Connect DCU to the printer and turn the power on. It show 7 LED on the panel and each code tells the function of the printer.
Normal Code
While printing or warming up, it indicate the position of the paper 61 00-05 Warm up Ready(kind of paper) The printer is on, the cover is open or close. The printer is ready, the paper is detected when the first paper is printed. 00: Legal ,01: Letter ,02: A4 ,03: EXEC ,04: B5 ,05: Folio, 06: A5/A6 The engine controller received the print order from the video controller. 20: 1st, 21: MP, 22: SCF The paper is passing out of the Feed Sensor. The paper has passed out of the Feed Sensor. The paper has passed out of Exit Sensor. The fuser power turned off to minimize the power consumption.
20, 21, 22 Print Start 30 40 50 69 Feed Sensor On Feed Sensor off Paper Out Sleep Mode
Error Code
When detecting the malfunction, the printing is stopped to indicate error code. 60, 62, 68 Fuser Error The error in the fuser occurred. There is a short circuit in the thermistor and the thermostat while printing, Low Temperature Error occurs. 60: Open Fuser Error 62: Low Heat Error 68: Over Heat Error The Printer Cover is open. The Toner Cartridge not installed, No paper in the paper cassette. The front part of paper is jammed between pickup unit and Feed sensor. The front part of paper is jammed between the Discharge sensor and Feed sensor. The front part of paper is jammed just after passing through the discharge sensor. The Out bin is filled with paper. LSU Scanner Motor not ready or Hsync signal not output.
64 65 70 71 72 73 76 95
Cover Open CRU Error No Paper Paper Jam 0 Paper Jam 1 Paper Jam 2 Out Bin Full LSU Not Ready
4-2
Samsung Electronics
Troubleshooting
00 01 02 03 04
Main Motor Operating System Only the main motor is in operation. Main High Voltage On(THV-) -1400 voltage output by MHV terminal. Transfer High Voltage(-)On(THV-) -1000 voltage output by MHV terminal. Transfer High Voltage (+)Reference on (THV +) +800 voltage output by MHV terminal. Caution : High voltage probe should be used. DEV/supply High Voltage : DEV/Supply High Voltage Test. The left one of the three LEDs in the self-test panel is on when DEV high voltage Supply high voltage output by each HV terminal(-500V). Press the [Up] button to switch the voltage. The middle and right one of the three LEDs are on and -650 voltage output by DEV HV terminal. Caution : High voltage probe should be used. Caution : High voltage probe should be used. Caution : High voltage probe should be used.
05
LSU Operating System The scanning motor of LSU is in operation, the right LED of the three buttons on. Press the [Up] button to Check LD. LD is functioning and the middle button is on. If the LD is normal, all LEDs are on.
06 07
Pickup clutch on The Solenoid in the printer is in operation. To stop the operation, Press the button [shift] and [Enter] together. Paper Empty(1st, SCF, MF) Sensor Test : If activate the Actuator of the PEMPTY/PWIDTH Sensor, the left and right of the three LEDs are on. Paper Empty Sensor (1st) ON/OFF Paper Empty Sensor (SCF) ON/OFF Paper Empty Sensor (MP) ON/OFF Increment DCU Code No. (08, Sensor TEST) 1st LED ON/OFF 2nd LED ON/OFF 3rd LED ON/OFF
08 09 10
Feed & Exit Sensor Test Test the Feed sensor and Discharge sensor in the same way as '06'. Cover Open Sensor Test The same way as code '06'. Fuser Test If the [Enter] button pressed, the right LED is on and temperature of the fuser is up to READY Mode. If the [Up] button pressed, the middle LED is on and temperature of the fuser is up to Printing Mode. If you press the button once more, the left LED is on and temperature of the fuser is up to overheat Mode.
11
Hot Burn Test If the [enter] button pressed, the printer is continuously printing without detection. Turn the power off to stop operation.
12
Cleaning Mode Print Mode Print the paper to clean the OPC Drum in the Cartridge.
Samsung Electronics
4-3
Troubleshooting
13
THV(+) TRIGGER. ALL HV : All high voltage output by each HV terminal and LSU and the fan is in operation. In this mode, electronic resistance of transfer roller and high voltage is detected.
14 15 16
+7P Clutch Test : Same method of the code 06. Fan Test : Indicates the function of the fan, same method of the code 06. Paper size Sensor Test : Cassette Sensor 1 ON/OFF Cassette Sensor 2 ON/OFF Cassette Sensor 3 ON/OFF Increment DCU Code No. (00,MAIN MOTOR TEST) Decrement DCU Code No. (15, FAN TEST) 1st LED ON/OFF 2nd LED ON/OFF 3rd LED ON/OFF
17
SMD Test : This function is for a manufacturing process. You can test all diagnostic Codes(0~06). When you push the Enter button, the main motor runs (Diagnostic Code 00). If you push the up botton, the current diagnostic Code stops, and the next diagnostic Code starts.
FACE DOWN
FACE UP
FUSER
LSU
CARTRIDGE
PTL
H/R
EXIT1
CR
DR
FEED SEN
SR
OPC
Pr/R
IDLE
EXIT SEN
TR
FEED
PICK UP
EMPTY SEN
CASSETTE
SCF
4-4
Samsung Electronics
Troubleshooting
SELF TEST
STATUS DIAGNOSTIC
ON
OFF
DIAGNOSTIC CODE
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17
MAIN MOTOR OPERATION MAIN HIGH VOLTAGE ON TRNSFER HIGH VOLTAGE (-)ON THV(+) REFERANCE VOLTAGE DEV/SUPPLY VOLTAGE ON LSU OPERATING TEST PICKUP CLUTC ON PAPER EMPTY SENSOR TEST FEED & EXIT SENSOR TEST COVER OPEN SENSOR TEST FUSER TEST HOT BURN TEST CLEAN (MESSAGE)PRINT THV(+)TRIGGER &THV ON MP PICKUP ON FAN TEST PAPER SIZE SENSOR TEST SMD TEST
STATUS CODE
00 01 02 03 04 05 06 20 21 22 40 50
READY (REGAL) READY (LETTER) READY (A4) READY (EXECUTIVE) READY (B5) READY (FOLIO) READY (A5,A6) PRINT START (1st CASSETTE) PRINT START (MP) PRINT START (2nd CASSETTE) FEED SENSOR 2st ON PAPER OUT
DCU MODE
DOWN UP
SHIFT
STOP ENTER
O ENTER DIAGNOSTIC MODE, PUSH THREE BUTTONS SIMUL ANEOUSL THE PRINTER POWER ON.
Samsung Electronics
4-5
Troubleshooting
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
2. Scratched surface of the discharge roller in the developer. 3. Partly depression or deformation on the surface of the transfer roller.
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
Check and Cause 1. Foreign matter stuck onto the window of internal lenses of LSU mirror.
Solution 1. Foreign matter stuck onto the window : Clean the LSU window with recommended cleaner(IPA) Clean the window with a clean cotton swab. 2. Foreign matter in the LSU : Open the cover of LSU and clean with a cotton swab on the surface of the reflex mirror.
2. Foreign matter or toner particles between the developer roller and blade. (In case the life of the developer has been expired, white lines or light image occur in front of the image.) 3. It may occur when Burr and foreign substances are on the window of the developer frame. 4. If the fuser is defective, voids occur periodically at the top of a black image.
3. No 3. : Remove the foreign matter and burr of the exposure window. (Developer cartridge) 4. No. 4. : Open the front cover and check ribs that corresponds to the position of the voids. Remove if found. 5. If the problems are not solved, replace the developer cartridge.
4-6
Samsung Electronics
Troubleshooting
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
2. The rollers of developer may be stained. Charge roller = 38.5mm Supply roller = 51mm Develop roller = 50mm Transfer roller = 56.8mm
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
2. In case of 96 mm interval unremovable in 1, cleanly remove foreign substances stuck on the OPC location equivalent to black spots and white spots with a dry duster. 3. The transfer roller guarantees 125,000 sheets printing. If the roller's life is expired, replace it. 4. In case of 38.5 mm interval unremovable in 1, take measures as to replace the developer cartridge and try to print out. 5. Clean the inside of the set against the paper particles and foreign matter in order not to cause the trouble.
Samsung Electronics
4-7
Troubleshooting
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
Check and Cause 1. Develop roller is stained when the toner of developer cartridge is almost consumed. 2. Ambient temperature is below than 10C.
2. No 1 : Replace the developer cartridge and try to print out. 3. No 2 : Wait 30 minutes after printer is powered on before you start printing.
3. Bad contact caused by the toner stains between the high voltage terminal in the HVPS and the one in the set. 4. Abnormal output from the HVPS. (Run self-test and check 1~4)
5. Replace the HVPS if the problems are not solved by the above four directions.
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
Check and Cause 1. No charge voltage in the engine board. ( Perform DCU diagnostic code 01) 2. Charge voltage is not turned on due to the bad contacts between power supply in the side of the Developer and charge terminal of HVPS.
2. Check the state of the connector which connects the engine board and HVPS.
4-8
Samsung Electronics
Troubleshooting
Check and Cause 1. The pressure force on the left and right springs of the transfer roller is not even, the springs are damaged, the transfer roller is improperly installed, or the transfer roller bushing or holder is damaged. 2. The life of the Developer has expired.
2. Occur in the developer cartridge, replace the developer and try to print out.
3. The toner level is not even on the developer roller due to the bad blade.
4-2-8 Background
Description Light dark background appears in whole area of the printing.
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
3. The up-to-down movement of the transfer roller is swift? 4. The HVPS is normal? (Perform DCU diagnostic code 01~04)
Samsung Electronics
4-9
Troubleshooting
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
Check and Cause 1. Bad contacts caused by contamination from toner particles between high voltage terminal in the main body and the electrode of the Developer. 2. Bad contacts caused by contamination from toner particles between high voltage terminal in the main body and the one in the HVPS board. 3. The life of developer is expired.
96 mm 96 mm
2. Occur in the developer cartridge, replace the developer and try to print out.
3. Replace the engine board if not solved by the above directions 1-2.
4. If not solved by the direction 3, check the transfer roller lifetime and replace it.
5. Wait about 1 hour after power on before using printer. 6. Occur in the developer cartridge, replace the developer and try to print out.
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
4-10
Samsung Electronics
Troubleshooting
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
Solution 1. Occur in the developer cartridge, replace the developer and try to print out. 2. Check the approved voltage of the supply roller and contact of the terminal and adjust if necessary.
2. The abnormal voltage and bad contact of the terminal of the supply roller
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
Solution 1. Disassemble the fuser and remove the contaminated toner particles on the roller and clean the foreign matter between Thermistor and Heat roller. ( Caution: can be deformed)
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
Check and Cause 1. Toner leakage due to improperly sealed developer. 2. If the transfer roller is contaminated, satins on the face of page will occur.
2. If the transfer roller is contaminated, run PC Cleaning Mode Print 2 or 3 times. And perform Self-Test 2 or 3 times to remove contamination.
Samsung Electronics
4-11
Troubleshooting
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
Solution 1. Perform the OPC Cleaning Mode Print 2 or 3 times. Run Self-Test to remove the contamination of the transfer roller. 2. Replace the transfer roller if contaminated severely. 3. Disassemble the fuser and clean the H/R(Heat Roller) and P/R(Pressure roller). And check the area between H/R and Thermistor. If contaminated, clean the area not to be deformed.
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
Solution Remove contamination of the terminals of the developer and the unit.
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
Troubleshooting
Description
Check and Cause Wrong sense time caused by defective feed sensor actuator.
4-3-2 JAM 0
EXIT2
1. Paper is not exited from the cassette. 2. Jam-0 occurs if the paper feeds into the printer.
FEED SEN IDLE
FACE UP
FUSER
H/R
EXIT1
LSU
CARTRIDGE
Pr/R
TR
FEED
PICK UP
CASSETTE
JAM 0
4. If continuous clusters occur, check whether the assembly slot between shaft-pickup and housing-pickup become open or is broken away. 5. If the paper feeds into the printer rand Jam 0 occurs, perform DCU to check feed-sensor of the engine board.
Samsung Electronics
4-13
Troubleshooting
4-3-3
EXIT2
JAM 1
FACE DOWN
LSU
FACE UP
CARTRIDGE Description
FUSER
H/R
EXIT1
IDLE
1. Recording paper is jammed in front of or inside the fuser. 2. Recording paper is stuck in the discharge roller and in the fuser just after passing through the Actuator-Feed.
EMPTY SEN
Pr/R
TR
FEED
PICK UP
1. If the recording paper is jammed in front of or inside the fuser. (Perform DCU diagnostic code of)
CASSETTE
JAM 1
2. If the recording paper is stuck in the discharge roller and the fuser just after passing through the ActuatorFeed, Feed Actuator may be defective.
4-3-4 JAM 2
Description FACE DOWN
EXIT2
FACE UP
FUSER
H/R
EXIT1
LSU
1. Recording paper is jammed in front of or inside the fuser. 2. Recording paper is stuck in the discharge roller and in the fuser just after passing through the Actuator-Feed.
IDLE
CARTRIDGE
Pr/R
TR
FEED
Solution 1. Check if the exit sensor actuator is defective. Check if the actuator exit is unformed (Check if the lever part is unformed in shape). Check whether burrs occur in the assembly part of the actuator exit or not and if the actuator is smoothly operated. Check if foreign matters and wire get caught in the actuator exit's operation. 2. If the paper is stuck in the fuser : disassemble the fuser and remove the jammed paper, and clean the surface of the pressure roller with dry gauze.
PICK UP
CASSETTE
JAM 2
1. If the paper is completely fed out of the printer, but Jam 2 occurs : Exit sensor is defective. After the paper is completely discharged, actuator Exit should return to the original position to shut the photo-sensor. Sometimes it takes longer hour than it should and does not return.
2. If the paper is rolled in the Fuser Roller: This occurs when a Guide claw is broken away or transformed. It occurs when the Spring of a Guide claw is broken away or transformed. It occurs when the Heat-Roller or Pressure-Roller is seriously contaminated with the toner. 3. Paper is accordion in the fuser.
3. Remove the jammed paper after disassembling the fuser : Clean the surface of the pressure roller with dry gauze. Remove the toner particles stained on the rib. Check the assemblage and performance of the exit.
4-14
Samsung Electronics
Troubleshooting
4-3-5 Multi-Feeding
Description Multiple sheets of paper are fed at once.
Check and Cause 1. Solenoid malfunction(the solenoid does not work properly): Perform DCU mode : solenoid check 06. 2. Pad-Friction is contaminated with foreign matter.(oil...)
2. Clean the pad friction with soft clothe dampened with IPA(Isopropyl Alcohol). 3. Use the smooth paper.
Check and Cause 1. Contamination of the pressure roller. (Background, Hot off set)
Solution 1. Disassemble the fuser, clean the area between the Heat-roller and Thermistor and remove the foreign matter of the pressure roller. 2. If background appears badly in the printing, fix it by referring to the solutions for background. (See 4-2-8 Background)
Samsung Electronics
4-15
Troubleshooting
4-3-7
OPC
Paper is rolled up in the OPC.
Description
Check and Cause 1. Paper is too much thin. 2. The face of paper is curled.
Solution 1. Recommend to use normal paper. 2. How to remove the rolled paper in the OPC. Remove the paper while turning the OPC against the ongoing direction. Clean fingerprints on the OPC softly with soft cloth dampened with IPA(Isopropyl Alcohol) or tissue.
4-16
Samsung Electronics
Troubleshooting
3. Check if the heat lamp works properly. 4. Check if the overheat circuit works properly. 5. The fuser gear is defective due to melting away.
Check and Cause DCU Mode : Perform DCU diagnostic code 05. If the DCU error code 95 is displayed, replace LSU. Replace LSU.
Solution
If you cannot solve the problem after you replace LSU, replace the main board.
Samsung Electronics
4-17
Troubleshooting
4-4-3 Not function of the gear of the fuser due to melting away
Description The motor breaks away from its place due to gear melting away.
Check and Cause DCU Mode : Check if the Error States '60' '62' '68' occur. Check the operation of Fuser Erasing Lamp On/Off with the Error Code Check -10-. 1. Replace the Fuser.
Solution
Check and Cause 1. Bending or deformation of the actuator of the paper sensor. 2. The function of the engine board is defective Perform DCU mode: Perform DCU diagnostic code 8.
Check and Cause 1. Bending or deformation of the actuator of the paper sensor. 2. The function of the engine board is defective Perform. DCU mode : Perform DCU diagnostic code 8.
4-18
Samsung Electronics
Troubleshooting
Check and Cause 1. The Hook Lever in the top cover may be defective.
2. Check the connector (Engine BdHVPS) and circuit of the cover switch department in the Main Control board. Perform DCU mode : If Error state '64' occurs, Check the related codes of the Cover Open Error.
Hook Lever
Check and Cause 1. Check the connector(CN8) and circuit of the cover switch department in the Main Control board. Perform DCU mode : If Error state '64' occurs, Check the related codes of the Cover Open Error
Samsung Electronics
4-19
Troubleshooting
4-4-9 No Power
Description When system power is turned on, all lamps on the operator panel do not come on.
Check and Cause 1. Check if the power input and SMPS output are normal.
2. Check the inferiority of LED-Panel on the front-cover if the LED of Panel does not appear after normal warmingup.
4-20
Samsung Electronics
Troubleshooting
Check and Cause 1. If the supply of +24v is unstable in the Main Control board linking with LSU, check drive by DCU Mode: LSU Check -05- LSU Motor on. 1. Replace LSU.
Solution
Samsung Electronics
4-21
Troubleshooting
One-way Screw
One-way Screw
4-22
Samsung Electronics
Troubleshooting
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
1. If the image is light or unclean and untidy printed image Shake the developer and then recheck. Some part of the (1)NG: Check the weight of the image is not printdeveloper ed. (2)OK: Lack of toner, so the life is nearly closed. Periodically a noise 2. Some part of image is not as "tick tick" occurs. printed - Shake the developer and then recheck. (1)NG: Check the weight of the developer and clean the LSU window with a cotton swab, then recheck. (2)OK: Lack of toner, so the life is nearly closed. 3. Periodically a noise as "tick tick" occurs - Measure the cycle and the weight of the developer.
2. In case of 2If it becomes better after cleaning the LSU window, then the developer is normal. (Because of foreign substance on the LSU window, the image has not been printed partly.)
4. White vertical stripes on the whole screen or partly : Check the weight of the developer. Toner Contamination Toner is fallen on the papers periodically. Contaminated with toner on prints partly or over the whole surface. 1. Toner is fallen on the paper periodically. (1)Check the cycle of the falling of the toner. (2)Check the appearance of both ends of the developer OPC drum. 2.The center of the printed matter is contaminated with toner. (1)Check whether foreign substances or toner are stuck to the terminal (contact point) of the developer. (2)Check whether the state of the terminal assembly is normal.
3. In case of 3If the cycle of noise is about 2 seconds, the toner inside the developer has been nearly exhausted.( Purchase and replace with a new developer after using about 200 sheets at the point of occurrence) 4. In case of 3This is a phenomenon caused by lack of toner, so replace with a new developer. 1. If both ends of the OPC drum are contaminated with toner: Check the life of the developer.
Samsung Electronics
4-23
Troubleshooting
Solution 1. In case of 1 above Run OPC Cleaning Mode Print 4-5 times repeatedly to remove. Especially check foreign substance on the OPC surface, then remove them with a clean gauze moistened with IPA(Isopropyl Alcohol) not to damage OPC if necessary. Never use usual alcohol. 2. In case of 2 If they are not disappeared by running OPC Cleaning Mode Print 4-5 times. : at intervals of 38.5mm - Replace the developer. : at intervals of 96mm - Remove foreign substance. : Broken image - Replace the developer according to carelessness. 3. In case of 3 - Exchange the transfer roller because the life of the transfer roller in use has been expired. (Check the transfer voltage and readjust if different.)
Digital Printer Digital Printer Digital Printer Digital Printer Digital Printer
1. If light or dark periodical black dots occur, this is because the developer rollers are contaminated with foreign substance or paper particles. White spots occur in the image period- (1)38.5mm interval : Charged roller ically. (2)96mm interval : OPC cycle
2. If white spots occur in a black image at intervals of 96mm, or black spots occur elsewhere, the OPC drum is damaged or foreign substance is stuck to the surface.
3. If a black and white or graphic image is partially broken at irregular intervals, the transfer roller's life has been expired or the transfer voltage is abnormal. Recycled product Poor appearance of 1. Poor appearance of the develthe developer. oper. (1)Check the damage to label Unclean and rough and whether different materiprintouts. als are used. (2)Check the appearance of Bad background in parts of the developer, such the image. as frame, hopper.
1. In case of 1 (1)If there is an evidence of disassembling the developer. (2)If materials other than normal parts of the developer are added or substituted.
2. Unclean and rough printouts. (1)Check whether foreign substance or toner are stuck to the terminal (contact point) of the developer. (2)Check whether the state of the terminal assembly is normal.
2. In case of 2 - If there are any abnormals in connection with the situation of 1. (1)It occurs when the developer is recycled over 2 times. (2)If toner nearly being expired are collected to use, it is judged as the recycled developer.
4-24
Samsung Electronics
Troubleshooting
Signs The printed image is too light or dark, or partially contaminated black. Totally contaminatedblack. (Black image printed out) The density of printouts is too dark and ghost occurs.
Cause & Check 1. The printed image is too light or dark, or partially contaminated black. (1)Check whether foreign substance or toner are stuck to the terminal(point of contact) of the developer. (2)Check whether the terminal assembly is normal.
Solution 1. All of 1, 2, 3 above (1)Remove toner and foreign substances adhered to the contact point of the developer. (2)The contact point of the unit facing that of the developer also must be cleaned. (3)If the terminal assembly is unsafe: Fully stick the terminal to or reassemble it after disassembling. Disassemble the side plate and push the terminal to be stuck, then reassemble it. 2. In case of 2 It is a phenomenon when the OPC drum of the developer is not electrically charged. Clean the terminals of the charged roller, then recheck it.
2. Totally contaminated black. (Black image printed out) (1)Check whether foreign substances are stuck to the terminal(point of contact) of the developer and the state of assembly. (Especially check the charged roller terminal.)
3. The printed image is dark and ghost occurs. (1)Check foreign substance attached to the terminal (point of contact) of the developer and the state of assembly. (Especially check the developing roller terminal.)
3. In case of 3 It is a phenomenon as the developing bias voltage of the developer. Clean the terminals of the developing roller, then recheck it.
Samsung Electronics
4-25
Troubleshooting
Check and Cause 1. Run Self-Test Mode: Turn the power on while pressing the test printing button for 2 or 3 seconds before printing works.
Solution 1.Check the power of the printer and perform the SelfTest. If the test printing works, that means no problems in the printer itself. If the test printing does not work, that means bad functioning of the printer(not because of software). Perform DCU to check the Error Status. 2. Replace the printer cable. If the problems not solved even after the cable replaced, check the amount of the remaining tone. (refer to Toner Cartridge Service 4-5) 3. Check if the connection between PC and printer port is proper. If you use windows, check if the printer driver in the controller is set up. If the printer driver is properly set up, check in which program the printing is not working. The best way to find out is to open the memo pad to check the function of printing. If it is not working in a certain program, adjust the setup the program requires. Sometimes, the printout is normal within the Windows basic programs, but it's not working in a particular program. In such case, install the new driver again. If not working in the Windows basic program, Check the setup of the port of CMOS is on ECP. And check the address of IRQ 7 and 378
2. Check if the PC and the printer is properly connected and the toner cartridge installed.
4. If the scanner needs to be connected to the printer, first the remove the scanner from the PC to see if the printer is properly working alone.
4-26
Samsung Electronics
Troubleshooting
2. Printing error occurs even if there is enough space in the hard disk.
3. As a printer port, Select ECP or SPP among SPP(Normal), ECP, and EPP modes(increase printing speed) SPP normal mode support 8-bit data transfer, while ECP Mode transfer the 12-bit data.
4. If the regular font is not printing, the cable or the printer driver may be defective. Turn the PC and printer off, and reboot the system to print again. If not solved, double-click the printer in my computer If the regular fonts are not printed this time again. the cable must be defective so replace the cable with new one.
Samsung Electronics
4-27
Troubleshooting
Description
2. Check the printer in My Computer.(to see if the printer driver is compatible to the present driver or delete the old driver, if defective and reinstall the new driver)
3. Error message from insufficient memory. (The printing job sometimes stops or due to insufficient virtual memory, but it actually comes from the insufficient space of the hard disk.)
3. Delete the unnecessary files to secure enough space of the hard disk and start printing job again.
4-28
Samsung Electronics
Troubleshooting
Description
2. If there are some files with the extension name of ****.jnl, Delete them and Reboot the Windows to restart printing job.
3. Shut down all other programs except the current one, if possible.
5 After rebooting the computer, check for viruses, restore the damaged files and reinstall the program to do the printing job.
How to delete the data in the spool manager. In the spool manager, the installed drivers and the list of the documents waiting to be printed are shown. Select the document to be deleted and check the delete menu. If you intend to delete the current document being printed, the data being transferred to the printer will be put out and then the document is removed. Before choosing the document, the menu is still inactive. Or put the document out of the list and repeat the routine as in the above or finish the spool manager.
Samsung Electronics
4-29
Samsung Electronics
3-1
3-2
Samsung Electronics
Samsung Electronics
3-3
Push the solenoid if you have difficulty to remove the pickup assembly.
3-4
Samsung Electronics
2. Remove two screws at the back of the printer and unplug one connector from the board, then open the rear cover.
Note that the power switch and the power connecter are properly released when you remove the cover.
Samsung Electronics
3-5
4. If you want to remove the exit roller, sqeeze the bottom of the roller and take it out.
3-6
Samsung Electronics
3-8 LSU
1. Before you remove the LSU, you should remove: -Main Cover (see page 3-5) -Exit assembly (see page 3-7)
2. Remove four screws, and remove the LSU. Then unplug two connectors from the LSU.
Samsung Electronics
3-7
2. Remove six screws securing the drive assembly from the gear bracket and unplug one connector from the motor, and then take the drive assembly out.
3. If you want to remove the motor from the drive assembly, remove three gold screws securing the motor assembly to the gear bracket.
3-8
Samsung Electronics
3-11 Fan
1. Before you remove the fan, you should remove: -Main Cover (see page 3-5)
2. Remove two screws, and remove the fan. Then unplug one connector.
3-12 Solenoid
1. Before you remove the solenoid, you should remove: -Main Cover (see page 3-5)
2. Remove two screws, and remove the solenoid. Then unplug one connector.
Samsung Electronics
3-9
2. Remove four screws and unplug one connector, and then remove the fuser assembly.
To remove the halogen lamp from the fuser assembly : Remove two screws and take the halogen lamp out of the fuser assembly.
To remove the thermostat from the fuser assembly Remove two screws and take the thermostat out.
Note: When you reassemble the halogen lamp, make sure that it is inserted into the slot properly.
3-10
Samsung Electronics
To remove the heat roller from the fuser assembly : 1. Remove the halogen lamp. (see page 3-11)
2. Remove two CS-rings and two gears. Then remove two screws securing the BRKT gear fuser and take the gear fuser out.
CS-ring
pressure roller
4. Remove two screws and take the holder brush ant out.
Samsung Electronics
3-11
2. Release the latches on the PTL lamp from the MPF assy and unplug one connector, then remove the PTL lamp.
PTL lamp
3. Remove two screws and raise the guide feed in the direction of arrow.
3-12
Samsung Electronics
2. Remove nine screws securing the PCU shield and remove two screws securing the SCF connector, and then take the PCU shield out of the printer.
4. Unplug all connectors from the PCU shield, and remove the shield.
Samsung Electronics
3-13
To replace the exit board : Unplug one connector from the controller board and remove one screw securing the board. Then release the wire from two holders and take the board out.
To replace the Cap sensor : Remove two screws and take it out.
To replace the fuser sensor : Remove two screws and take it out.
To replace the actuator empty : Take the sensor out while you squeeze the both ends of the sensor.
Actuator empty
3-14
Samsung Electronics
To replace the actuator feed 1. Turn the mechanism back and push down the points as shown to unlatch the actuator feed.
To remove the transfer guide : Remove three screws and take the guide out.
2. Turn the unit over again, and remove the actuator feed.
Samsung Electronics
3-15
Specifications
2. Specifications
Engine Speed Resolution First Print Time Warm-Up Time Power Consump. Dimension(W * D * H) Weight Acoustic Noise Power Rating Controller Processor Memory RAM ROM EEPROM Emulation Interface OS Support N/W Paper Input Output Media Type Toner Periodic Replacing Parts User interface Type Life Pick up Roller Feed Roller Transfer Roller Fuser Key & LED LCD Toner Save Reprint Environment Operation Environment Temperature Humidity Storage Environment Temperature Humidity Cassette Face down Face up 15 PPM(Letter) , 14 PPM(A4) True 600 X 600 dpi Tray 1 : Less than 15 seconds Tray 2 : Less than 17 seconds Less than 40 seconds Print : 350 W, Power save mode : Less than 12 W 361 x 409 x 247 mm 11.2 Kg/ 24.7 lb (SET) Stand by : Less than 35 dB, Operating : Less than 48 dB AC 100~120 V , 50 Hz AC 220~240 V , 60 Hz Power PC (66 MHz) 8M (Not Expandable) 4 Mbyte (16M bit x 2 : Program) Flash Memory 512 bytes SPL(Samsung Printer Language) IEEE1284, USB Windows 95/98/2000/ME/NT/XP Linux(Redhat 6.0 ), iMac(Mac OS 8.0 ) Option 270 sheets (75g/m2) 250 sheets 100 sheets A4, Letter. Legal, Executive, B5, A5, Folio, 7 3/4(Monarch), #10, DL, C5, C6, B5 Single Cartridge 6,000 sheets (Set : 3,000 sheets) 75,000 sheets 75,000 sheets 75,000 sheets 75,000 sheets 3Key, 4LEDs No YES YES(Button) 10 ~32c (50F ~ 90F) 20 ~ 80 % RH -20 ~40c (4F ~ 104F) 10 ~90 % RH
Samsung Electronics
2-1
Precautions
1. Precautions
Please read the following carefully to prevent any accidents and not to damage the unit during service.
Especially mind the safety on the part with this mark. You must use regular parts described in specifications for the parts inflammable and where the current can be flown. Otherwise any hazard such as an electric shock or a fire could occur.
LASER STATEMENT (LASERTURVALLISUUS)
WARNING : NEVER OPERATE AND SERVICE THE PRINTER WITH THE PROTECTIVE COVER REMOVED FROM LASER/SCANNER ASSEMBLY. THE REFLECTIVE BEAM, ALTHOUGH INVISIBLE, CAN DAMAGE YOUR EYES.
Class 1 laser product Luokan 1 laserlaite Klass 1 laser apparat Allonpituus 770-795nm Teho 0.3mW0.03mW
CAUTION VORSICHT
INVISIBLE LASER RADIATION WHEN THIS COVER OPEN. DO NOT OPEN THIS COVER. UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG GEOFFNET. NIGHT DEM STRAHL AUSSETZEN.
ATTENTION
REYONNEMENT LASER INVISIBLE EN CAS DOUVERTURE. EXPOSITION DANGERUSE AU FAISCEAU. RADIAZIONE LASER INVISIBLE IN CASO DI APERTURA. EVITARE LESPOSIZONE LA FASCIO. REDIACION LASER INVISIBLE CUANDO SE ABRE. EVITAR EXPONERSE AL RAYO.
ATTENZIONE PRECAUCION
1-1
Precautions
1-2
Samsung Electronics
Precautions
Standard: Test equipment to diagnose the Laser printer supplied by Samsung Electronics.
Driver
Standard: "-" type, "+" type (M3 long, M3 short, M2 long, M2 short).
Pinset
Standard: For general home use, small type.
Cotton Swab
Standard: For general home use, for medical service.
7 3 Electronic Scale 8
Standard: Equipment to check the weight of consumables(toner cartridge) supplied by Samsung Electronics. (The gram unit can be measured.)
Note
Mind your hands not to be touched when you disassemble and reassemble PBA ASS'Y, such as the main board, SMPS, HVPS.
Samsung Electronics
1-3