Professional Documents
Culture Documents
Revision 3.0
Mar 2012
TECHNOLOGY
worlds rst electric bike computer come with data logging and live view via cell phone !
electrical parameters hassle free using their bluetooth enabled cell-phone, built-in android smart connected, location information is also be recorded.
1. 2. 3. 4. provides voltage, speed, temperature, current cut-off, current throttle and en15194 compliant ... support standard java midp 2.0 or below, and bluetooth access via btapi depended on cell-phone model (as tested with motorola slvr l7, the range is up to 80m) android smart phone with a-gps built-in
Functions
The ebike measures and records speed, current, voltage and temperature over
time, then use these measurements to calculate the maximum power (watt), battery consumption (mah). Real-time information as to live and peak current, live and used voltage, current and maximum power (watt), as well as existing and consumed capacity (mah) is transmitting using bluetooth technology. Biker can use their cell-phone to read these data in real-time for their pleasure or to fine-tune their power system.
Page - 01
function mode allows configurable function model through its on-board 4 i/o ports, in combining with governor features it can provide riders needs on both safety and system utilization. for instance, configure speedict ebike to measure pedal cadence rate, matching cadence rate for power delivery, redefine throttles highest and lowest point and even configure to compliant with en15194 standard. The ebike can save up to 12 hours of information. Bikers can download their logged data to their computer using a usb cable and manage the data and performance charts with the included pc software, or upload to the internet for store, review and share purpose. the ebike can be used in difference ways to enhance your electric-powered bike experience as follow : trip information recorder, charger and battery health monitor, road legal smart device, protect power system by current, voltage and temperature cut-off, system diagnostic and optimization equipment.
Benefits
new way to fine-tune the performance of their electrical powered bike for things such as : maximize trip time, maximize trip distance, controller and motor efficiencies through knowledge of current flow through controller and motor, improve battery life by monitoring battery health, charger performance and current put through, and discharge from a battery, eliminate potential risk of damaging components with peak current, reduce voltage sags that cause components to operate out of specification, feedback as to why power is lost during different trip conditions, effects of modifications, aging, and damage on many electrical system components, safe guard power system by govern speed, current, voltage and temperature cut-off transforms generic speed controller with smart features like 1:1 pas, cruise, utilize throttle range, current throttle, turn your electric bike to compliant with local regulation e.g. en15194 for european countries.
Page - 02
Features
measures and records current, voltage, speed and temperature over time real-time calculations capacity used (mah) of the maximum power (watt) and
displays real-time information on java enabled cell-phone or android powered smart-phone streamed via bluetooth measures and records current, voltage, speed and temperature over time real-time calculations of the maximum power (watt) and capacity used (mah) displays real-time information on java enabled cell-phone or android powered smart-phone streamed via bluetooth massive built-in memory enables continuos live data recording for up to 12 hours computer management of logged data, performance charts and gps map route information using a usb cable and the included pc suite software govern / safe guard power system with cut-off capabilities built-in bluetooth and usb support, no additional hardware is needed future proof user firmware upgradable accurate & precise 0.01 a current, 0.01 v voltage and 0.1 km/h or mph resolutions durable handles +/- 100 a peak at 80 v smallest and lightest in its class, fits right into your battery compartment precision and low resistant (.00025 ohms) circuitry that doesnt affect electric bikes performance powerful 8 mips micro-controller factory calibration stores constants in eeprom to compensate for component tolerances comes with one-year limited warranty
Page - 03
Specifications
PARAMETER
Voltage Current Power Capacity Speed Cadence Odometer Trip distance Trip time Trip capacity Temperature
RANGE
6-80 v 1-100 a 0-65535 w 0-65535 mah 0-99.9 kmh / mph 0-999 rpm 0-999999 km 0-9999 km 0-99 hours 0-65535 mAh 0-100 c / f
RESOLUTION
0.01 v 0.01 a 1 w 1 mah 0.1 kmh / mph 1 rpm 1 km 1 km 1 second 1 mah 1 c / f
Miscellaneous Specifications
PARAMETER
Internal memory Log / record time Speed measurement period Measurement update period In circuit resistance Operation current Dimensions Weight Nominal operation conditions Bluetooth operation range
DATA / FORMAT
8 mbit / 1 mbyte 12 hours Instant 340 ms 0.00025 ohm 60 mA (with bluetooth) 45 x 29 x 11 mm 13 g / 23.4 g (including wires)
Page - 04
Bluetooth Specifications
FEATURE
Bluetooth transmission Fully bluetooth qualified Operating range Frequency Max / Min transmit power Receive sensitivity Temperature range
IMPLEMENTATION
Class 2 v2.0 + edr Up to 80 m (free space) (depends on cell-phone) 2.4 ~ 2.5 ghz +6 / -25 dbm Better than -86db @ 25c Normal operation : -40c to +85c
Safety Precautions
Electric-powered power electrical dangers and it bike that of use may high pose systems
causing fire, damage to equipment and personal injury. Limitation of your equipment Ebike is designed to operate within the parameter limits as in noted in the product the specification. Use of ebike systems exceeding safety limit of 80 volts, carrying damage
note :
adding ebike to the system users to be any these responsibility familiar dangers and
take
necessary action to ensure safe use. Improper use of equipment whilst using or can explosions, ebike may short circuit a rechargeable battery battery that charger
Page - 05
pas mode
throttle mode
road legal 1
road legal 2
throttle output
speed controller.
Port 3
Port 4
5.
function mode and governor work on android device only, for java mobile phone, please stay on firmware 1.2
Page - 06
Connect Diagram
Speedict ebike ship with firmware version 1.2 for java based mobile phone with simple live view and logger features, for advantage features such as location service, function mode, offline data and governor can via firmware upgrade and connect with android smart device. When connect with java mobile phone, speedict ebike can be connected with speed sensor and sensors for simple live view and logger features.
temperature
ground
5v
signal
When android smart device is in used and with firmware 2.3 or above is upgraded, Speedict eBike can be configured for different model safe guard your power system and compliant with local regulation !
Page - 07
Speed Controller
Battery
Page - 08
Speedict eBike
Function Mode
33
Present
6
(km/h)
23
Avg
Speed
8
(km/h)
Function mode with congurable function model through its on-board 4 i/o ports to provide riders needs on both safety and system utilization. Current Mode selected : N/A
Speed (km/h)
Multi-Sense
Default mode support up to 2 Temperature and 1 Speed sensor mainly for system monitoring
Max
6.19
18.21
18.9
37.0
Simply Cut
Monitor and simulate ebrake signal, sending braking signal to speed controller whenever cut off is needed
23.8 km/h
PAS
Capture and measure pedal cadence rate, matching power delivery for better power utilization
Throttle
Re-dene throttles low and high point for linearize throttle range, provide current and speed throttle
Speedict eBike
Speedict eBike
PAS Magnet #
Governor Setting
Speedict Android Client
Version 2.3
ON
ON
Current (A)
Function Mode
eBike Setting
Next
System Settings Governor Setting
Save
Cancel
Page - 09
Workow of java cell phone connection to eBike device ! example based on Sony Ericsson K770i
Download and copy eBike mobile client to java enabled cell phone
Go to the folder where the eBike mobile client program is located e.g. Application
Exit
Press Search button to search for any available Bluetooth device, Exit button to quit
Search Error message Select bluetooth device eBike (which is the default name) from the drivers list
No
Yes
Page - 10
No
Yes
No
No
Passcode matched ?
Yes Communication channel is established via bluetooth, start sending information to the paired cell-phone
Exit
Yes
Page - 11
Press key 4 Green light off and red light flashing Display voltage and its minimum value
Out of range
Within range
is
Quit program
Press Exit
Press #
Wrap up current record & creating new record (new session feature especially useful when new peak value recording is needed), this feature creates a new recording session without the need of power reset on eBike, all is done by press a key on cell phone
Press key 8
Communication channel is established via bluetooth, start sending information to the paired cell-phone
Press key 1
Press key 2
Page - 12
Speedict PC Suite
Windows based pc suite provides management for logged data such as graph plotting, gps map route plotting, editing, saving and deleting. Device related settings like firmware upgrades, tire circumference, name and odometer battery though reset, the device can be bluetooth passcode
configured
single without
executable
program
installation.
Speedict PC Suite
submit comment
rmware upgrade
le management
device setting
import data
record list
open le
save le
data chart
edit
delete
map route
tire circumference
upload to internet
Page - 13
1.1
1.2
connect a usb cable to both ebike and pc usb port, windows will immediately prompt found new hardware
1.3
in the found new hardware wizard dialog box, select yes, this time only. windows will not ask for drivers next time when the ebike is connected
1.4
select install from a list or specific location, and press the next button to continue ...
1.5
select search for the best driver in these locations and check include this location in the search:, press the browse button to locate the downloaded driver
1.6
the speedict usb driver is installed. the pc suite software is ready to import and manage recorded data from ebike
1.1
1.2
connect a usb cable to both ebike and pc usb port, windows 7 will prompt device driver software was not successfully installed
1.3
1.4
under the hardware and sound setting, click to the device manager
Page - 14
1.5
check to see if any unknown device under other devices type, then right click on it and select update driver software ... from menu
1.6
when prompt for driver software location, click to the browse my computer for driver software
1.7
1.8
when prompt for verify the driver software, click to the install this driver software anyway
1.9
1.10
the speedict usb driver is installed. the pc suite software is ready to import and manage recorded data from ebike
2.1
with the usb cable is still connected to both pc and ebike, you can run the speedict pc suite application by double click the speedict-pc-suite.exe
2.2
pc suite will start import records from ebike immediately when device is detected (or manual import by select data import from menu), press ok button to continuous
2.3
when import is completed, you can either press keep my data button to leave the records inside ebike, or press erase button to erase all record inside ebike
2.4
imported record(s) will be listed with its record date and time, you can edit, delete and view both chart and map route
Page - 15
3.1
click on any record and select gps map from menu to view chart and location information
3.2
on gps map windows, both recorded route and measured information are shown on top and bottom window
3.3
move cursor on bottom chart window, its detail information is shown on the lower right corner
3.4
3.5
drag and move cursor to left or right for next available time frame, use mouses scroll wheel for zoom in and out
3.6
3.7
all speed (sensor), voltage, current, capacity, watt, speed (gps measured) and temperature information are shown corresponded on time
3.8
click to the remove pin icon to remove all drop pin (s) on route window
3.9
click to view data icon to view different data information such as current, voltage, watt etc.
3.10
click to the upload icon to upload the current record to the internet
3.11
enter both verify code and your email address, press the upload button to upload
3.12
write down the web log id for later retrieve the shared log, press view now button to view the uploaded chart
Page - 16
4.1
on the record list page, click on any record and select chart item from menu to view chart
4.2
4.3
4.4
or
5.1
to edit record, simply click on record and select edit from menu
5.2
fill-in date, title, description and tag and then press the update button to update
5.3
to delete record, simply click on record and select delete from menu
6.1
on speedict pc suite front page, click on bluetooth menu item from setting menu for ebikes bluetooth related setting
6.2
ebikes bluetooth device name and passkey can be configured device name is use to identify ebike, on searching, device name will appear to cell phone
Page - 17
6.3
click on ebike menu item from setting menu for ebikes setting
6.4
for
6.5
6.6
select either mph or kmh on speed unit for unit display on both map route and chart window
6.7
select either celsius or fahrenheit on temperature unit for unit display on both map route and chart window
6.8
6.9
6.10
select correct tire circumference value from tire size list box for speed sensor measurement
6.11
value
7.1
click to the check for new version icon on the home page to check for available upgrade
7.2
click to the download now button under speedict pc client section to download new version
Page - 18
7.3
7.4
8.1
click to the check for new version icon on the home page to check for new available upgrade
8.2
click to the download now button under firmware section to download new version
8.3
8.4
8.5
click on the upgrade firmware button on home page to install the downloaded firmware note : button appears when ebike is plugged in and detected
8.6
8.7
8.8
wait until the upgrade process is completed, do not disconnect power at this time
Page - 19
9.1
click to the check for new version icon on the home page to check for new available upgrades
9.2
click to the download now & install button under Firmware section to download new version and install
9.3
9.4
9.5
wait until the upgrade process is completed, do not disconnect power at this time
9.6
firmware completed
upgrade
is
Page - 20
Caring Instruction
require special care, just gentle wipe the eBike with a damp cloth if it gets dirty and it can be stored anywhere other than an extreme environment or under direct sunlight for a prolonged period of time.
Technical Support
Please
visit
out
site
www.speedict.com
or
us
at
support@speedict.com for more technical support if you are still having difficulties or have questions that arent covered in this manual.
Warranty
workmanship for a period of one (1) year starting from the date of your original purchase. Please refer to the Speedict product warranty page for detailed terms and conditions as well as procedures for warranty claims.
Changes
is subject to change
The material in this manual is for owners information only and without notice. While reasonable efforts have been made in the
preparation of this manual to ensure accuracy, Speedict assumes no liability resulting from errors or omissions in this manual or from the use of information contained herein. Speedict reserves the right to make changes in the product design without reservation and without notification to users. Please check out our website www.speedict.com frequently for the latest user manual.
Copyright
any form or by an means,
Copyright (c) 2012 by Speedict. All rights reserved. No part of analog, digital, electronic or mechanical, including imaging,
this manual may, without the written permission of Speedict be reproduced or transmitted in photocopying and recording, for any purpose other than the owners personal use.
Page - 21