Professional Documents
Culture Documents
DESCRIPTION
The GM6108A is a high power-factor, constant current driver IC for offline LED lamps. It can accept dual input voltage range of 90V to 130VAC, and 180V to 270VAC. It is based on a sinusoidal buck/forward topology and achieves very high power factor, typically 0.97 or better. It supports both non-isolated (buck) and isolated (forward) designs. The GM6108A has a start-up current of less than 80uA. A bias winding on the buck converters inductor or the forward converters transformer provides the VDD power to sustain circuit operation after start up. The GM6108A provides an adjustable switching frequency, up to 200kHz. It has cycle-by-cycle current limit. The GM6108A provides an accurate internal current limit reference of 450mV. The GM6108A provides on-chip over-temperature protection. It shuts down the switching when the o junction temperature exceeds 150 C. The GM6108A is available in MSOP-10 package. Note: GreenMark patents:.US 7,295,452 and US 7,750,616.
APPLICATIONS
General LED lighting A19, PAR30, PAR38 LED light bulbs LED light tubes Outdoor spotlights
TYPICAL APPLICATION
GM6108A
ABSOLUTE MAXIMUM RATINGS
Supply Voltage VDD, GATE to GND...-0.3V to 22V Power Outputs and Control VCC, ISEN, VSINE to GND.... -0.3V to 6.0V CT, FBK, CAL to GND ..........................-0.3V to 6.0V Operating Junction Temperature .40oC to 125oC Storage Temperature Range..65oC to 150oC Lead Temperature (Soldering, 10 sec.).300oC
Package Thermal Resistance TJA .. 150oC/W
PIN DESCRIPTION
PIN 1 2 3 4 5 NAME VCC CT FBK GND CAL FUNCTION 5V LDO output Sets Toff length and nominal switching frequency Feedback input (from an opto-coupler) Ground Calibration for high line input power PIN 10 9 8 7 6 NAME VDD GATE ISEN VSINE NC FUNCTION Chip supply voltage Gate drive output for external MOSFET Current sense voltage input Scaled sinusoidal ac input waveform
GM6108A
ELECTRICAL CHARACTERISTICS
(VDD = 12.0V. Typical values are at TA = +25oC)
Conditions
Min
7.0
Typ
12.0 2.3 60 18.5 12.0 6.0 5.5 150 100
Max
Units
V mA uA V V V V
o
Fsw =100kHz, Ciss = 1nF VDD = 9.0V 17.5 10.0 5.8 Vin from 7V to 16V Switching is turned off. Note 1. Switching is resumed Note 1. Fsw =100kHz, Ciss = 1nF Fsw =100kHz, Ciss = 1nF 400 Note 2 1.45 4.9
UVLO Section
Turn-on threshold voltage Turn-off threshold voltage
LDO Section
VCC output voltage
Protection Section
Internal OTP shutdown threshold Internal OTP shutdown reset C C
o
Oscillator Section
Toff length Note 1: The parameter is guaranteed by design. It is not tested in production. Note 2: The current sense level-shift reference is correlated to a 1.20V internal reference voltage through a voltage follower buffer. Note 3: The CT capacitance required for a target Toff is, CT = Toff / 12.2k
GM6108A
FUNCTIONAL BLOCK DIAGRAM
AC V+
R1 Cin
AC V-
R3 R2 C5 0.2u 6.8u
VCC
VDD
OVP
GATE
FBK
Qvh turns on at high line Qvh Level Shift 1.50V
ISEN
S Qb 0.45V Toff LEB
CAL
GM6108A
CT
GND
GM6108A
APPLICATION INFORMATION
The GM6108A is a high power-factor, constant current driver IC for offline LED lighting. It can accept dual input range of 90V to 130VAC, and 180V to 270VAC. It is based on a proprietary sinusoidal buck topology to achieve very high power factor, typically 0.97 or better. The GM6108A supports both non-isolated (buck topology) and isolated (forward topology) designs. It has a start-up current of less than 80uA. A bias winding on the buck converters inductor or the forward converters transformer provides the VDD power to sustain circuit operation after start up. So if we keep Toff constant, the switching frequency Fsw will be higher when Vin is high. For 220VAC input, most of input power happens when Vin is above 100V. If Vf = 45V, and Toff = 8.5us, Fsw will be 65kHz at Vin = 100V. Fsw increases to 100kHz at Vin = 300V. Notice GM6108A improves Fsw range by making Toff shorter for lower Vin. Its Fsw range is typically from 80kHz to 100kHz.
No Electrolytic Capacitors
A large electrolytic capacitor takes up circuit board space and volume. Furthermore, its limited operating life, usually less than several thousand hours, will seriously downgrade the usable life of an LED lighting fixture. The operating life of an electrolytic capacitor can be expressed as
GM6108A
Lop = Mv*Lb* 2 [(Tm-Ta)/10] where Lop is the expected operating life in hours. Mv is a voltage multiplier for voltage de-rating. Lb is the expected operating life in hours at full rated voltage and temperature. Tm is the maximum permitted capacitor internal temperature in oC. Ta is the actual capacitor internal temperature in oC. In other words, an electrolytic capacitors life will be cut in half for every 10oC of temperature rise. In fact, a major challenge in designing a reliable LED lighting fixture confirming to the conventional incandescent light bulb form factor such as MR16, A19, PAR30, or PAR38 is the thermal management. The LED driver circuit is enclosed inside of a completely sealed chamber with elevated temperature. It is common to measure internal temperature of 100oC or more. This harsh operating condition often takes a toll on electrolytic capacitors. Therefore, to achieve longlife in LED lighting, it is desirable to eliminate the need for any electrolytic capacitors. . The inductor uses an EE10 ferrite core. The primary winding has 175 turns with an inductance of 5.6mH. The bias winding has 58 turns. The free-wheeling diode, D2, will see a full Vin when the MOSFET, Q1, turns on. We recommend a 1.0A, 400V ultra-fast recovery diode (ES1G). The bias winding voltage is in proportion to Vf at MOSFET off time. For Vf = 45V, and VDD = 14.5V, the bias winding number of turns is 175*14.5V/45V = 56T. Notice the reverse voltage on D3 is Vin*(58/175), when Q1 is on. We recommend a 200V ultra-fast recovery diode. Two 1N4148 in series can be used as well. No inrush current Fig. 3 shows the start-up waveform of the GM6108A driver. When VDD reaches UVLO cut-in level, the GM6108A starts switching. The start up can trigger at any phase angle of a 120Hz cycle. But Isen always follows the sinusoidal Vin waveform. Even at cold startup, there is consistently no inrush current.
Switching Waveforms
Fig. 4 shows the key waveforms of Fig. 2 circuit over a half cycle of 60Hz line frequency.
Thermal Design
Notice the safety isolation in Fig. 2 circuit is provided by the insulation layer between the LED devices and their aluminum substrate. An adequate heat-sink design for an LED light bulb can keep its outside surface temperature below 60oC. This in general will keep the junction temperature of the LED devices below 85oC. However, the air sealed within the air-tight light bulb chamber will be heated up by the heat dissipation from the inductor, the free-wheeling diode, and the power MOSFET. In many un-suspecting designs, the air trapped inside may get as hot as 150oC whereas the heat sink surface temperature is only 60oC. This trapped hot air often leads to component and circuit failure, especially in those LED drivers using electrolytic capacitors.
GM6108A
This circuit board hot spot situation is due to the lack of heat conduction path from the converter circuit board to the inside wall of heat-sink. Uncirculated air around the circuit board has very little heat transfer capability. The heat dissipated from the circuit board simply accumulates within the chamber, elevating the circuit board and components temperature to ever higher level. In certain light bulb design, convection holes are added to provide tiny amount of air flow in order to cool off internal temperature. Although effective, adding convection holes has the drawback of condensed moisture and trapped dust inside the lamp fixture. We recommend to apply heat conducting, but electrically insulating glue between the power dissipating devices (mainly the transformer, the power MOSFET, and the free-wheeling diode) and the inside wall of heat sink. One key to achieve over 90% efficiency is use to use LED modules with higher VF. This is due to the freewheeling diode loss is about Vd/VF. For example, if if Vd = 1.2V, and VF= 20V, the diode loss is near 5.4%. If VF is increased to 48V, the diode loss will be reduced to about 2%. The 3.4% efficiency improvement is quite substantial.
GM6108A
RCD Snubber Design
In a forward transformer, it is necessary to reset the core flux after each turn-on cycle. The minimum reset voltage required is according to the following equation, Vrst = Vin*D/(1-D) However, the voltage across C4 is typically higher than the minimum reset voltage. The reset voltage level and the RCD snubber design are related to several factors. Heuristically, we found a transformer with a good coupling (lower leakage inductance) between the windings will reduce the RCD snubber loss and the reset voltage level. In Fig. 5 circuit, C4 is 1n, R4 is 200K. Higher R3 will reduce the snubber loss, but the reset voltage will increase too. It is important to keep the reset voltage to less than 150V if a 600V MOSFET is used. Line Regulation and Calibration For low-line input range of 90Vac to 130Vac, GM6108A provides good line regulation of +/-3%. For high-line input range of 180Vac to 270Vac, GM6108A also provides a good line regulation of +/- 3%. However, for universal input range of 90Vac to 270Vac, we need to place a resistor, Rcal, between CAL (Pin 5) and FBK (Pin 3) to achieve tight line regulation. The proper value for the calibration resistance is related to the lamp power rating and VF value. We recommend to start with a 20K value for Rcal. After actual measurement of high-line output power, increase Rcal if high-line power is lower than low-line power; reduce Rcal if high-line power is higher than low-line power. An 18W LED Tube Design Fig. 6 shows a reference design for an 18W LED tube driver. It also uses an EEL-16 transformer. N1 and N2 are 120 turns each. Switching Waveforms Fig. 7A shows Vds and Isen waveforms of Fig. 5 circuit at Vin = 110Vac over a half-cycle of 60Hz line frequency. Fig. 7B shows Vds and Isen waveforms of Fig. 5 circuit at Vin = 220Vac.
GM6108A
Conduction loss = 0.19A*0.19A*3.4*0.3 = 37mW Switching loss = 40P*270V*270V*100k =146mW.
AC V+
Cx 0.1u
AC V-
C1 0.1u 2.2mH
C2 0.1u
R1 1M R2 20k
R3 820k D3 D2 56T C4 3.3u 175T D2: ES1G Q1: FQD3N40 400V, 3.4 Coss = 40pF EE10 175T: 56T L1 = 5.6mH
90V ~ 270VAC
GATE 47
Q1
GM6108A
CT 680p
CAL
20k
GM6108A app buck
Top trace: Vds (100V/div); Mid trace: VDD (10V/div) Bottom trace: Isen (200mV/div); Time base: 10msec/div Fig. 3 Start-up waveform
GM6108A
Top Trace: Vds (100V/Div) at 120Hz cycle Second trace: Isen (0.2V/Div) at 120Hz cycle Third trace: Vds (100V/Div) zoom-in at Fourth trace: Isen (0.2V/Div) zoom-in at Fig. 4 6W Buck Waveforms at 110Vac input
10
GM6108A
Confidential
11
GM6108A
Top Trace: Vds (100V/Div) in 60Hz half-cycle Second trace: Isen (0.2V/Div) in 60Hz half-cycle Third trace: Vds (100V/Div) zoom-in at Fourth trace: Isen (0.2V/Div) zoom-in at Fig. 7A 6W Forward Waveforms at 110Vac Input
12
GM6108A
Top Trace: Vds (100V/Div) in 60Hz half-cycle Second trace: Isen (0.2V/Div) in 60Hz half-cycle Third trace: Vds (100V/Div) zoom-in at Fourth trace: Isen (0.2V/Div) zoom-in at Fig. 7B 6W Forward Waveforms at 220Vac Input
Confidential
13
GM6108A
PACKAGE DIMENSIONS
MSOP-10
14
Confidential