Professional Documents
Culture Documents
MERE WAY, RUDDINGTON, NOTTINGHAM, NG11 6JZ, UK. TELEPHONE: 0115 936 6600 FACSIMILE: 0115 936 6702
NSK Corporation
3861 RESEARCH PARK DRIVE, PO BOX 1507, ANN ARBOR, MICHIGAN 48108, USA. TEL: 313-761-9500 FAX: 313-761-9510
INTRODUCTION
NSK-RHP is part of the International NSK Group who are one of the world's leading manufacturers of rolling bearings, automotive components and mechatronic products. The group has 36 manufacturing units around the world, employing over 24,000 people and is represented by sales offices, and authorised distributors almost everywhere. Our manufacturing programme includes bearings from 1mm bore to 5 metres, covering virtually all conceivable application areas.
Designation Systems 1/NRDS/E/12.97 Every care has been taken to ensure that the information in this publication is accurate but no liability can be accepted for any errors or omissions. Copyright NSK-RHP 1997 The contents of this publication are the copyright of the publishers
A member of the NSK Group
Designation Systems
Contents
NSK Standard Bearings
Pages 4 - 17
1 2 3 4 5 6 7
1
NSK Product
Manual Page No.
4 5 6 7 8 9 10 11 12 13 14 15 16 17 Metric series Radial Ball Bearings Inch series Radial Ball Bearings Metric series Single Row Angular Contact Ball Bearings Metric series Double Row Angular Contact Ball Bearings Metric series Four Point Contact Ball Bearings Metric series Cylindrical Roller Bearings Metric series Tapered Roller Bearings Inch series tapered roller bearings Metric series Double Row Spherical Roller Bearings Metric series Single and Double Direction Ball and Spherical Roller Thrust Bearings Angular Contact Thrust Ball Bearings Metric series Miniature Deep Groove Ball Bearings Special Metric series Miniature Deep Groove Ball Bearings Inch series Miniature Deep Groove Ball Bearings
Bearing Series
19 20 21 23 24 26 28 25 -
Designation Systems
2
RHP Product
Manual Page No.
19 20 21 22 23 24 25 26 27 28 29 30 Metric series Radial Ball Bearings Inch series Radial Ball Bearings Metric series Single Row Angular Contact Ball Bearings Inch series Single Row Angular Contact Ball Bearings Metric series Double Row Angular Contact Ball Bearings Metric and Inch series Four Point Contact Ball Bearings Metric and Inch series Single Direction Thrust Ball Bearings Metric series Cylindrical Roller Bearings Inch series Cylindrical Roller Bearings Metric series Double Row Spherical Roller Bearings Metric series Double Row Spherical Roller Bearings for use in vibratory equipment Externally Aligning Ball and Roller Bearings
Bearing Series
4 5 6 7 8 13 9 12 12 -
Section 1
6 6
2 10
TYPE
2 10
DIMENSION SERIES
BORE CODE
type) type) type) type) type) type) type) type) type) type) type)
For bore code 04 upwards, the general rule is to multiply by 5 to obtain bore size in mm. The exceptions to this are bearings with bore diameter of 22mm, 28mm, 32mm and 500mm and above. These are denoted by the type and ISO series (60, 62, 63), followed by / and the bore diameter in mm ie. 62/22, 63/32 etc.
Not usually included for pressed steel (J) type cage For others see list of CAGE TYPE CODES on Appendix 1 Page 32
ZZ K C2
K Tapered bore 1 : 12 K30 Tapered bore 1 : 30 E Notch or Lubricating groove in ring For other ring configurations see Appendix 2
INTERNAL CLEARANCE
C1 C2 CN C3 C4 C5 CM CG*
Radial clearance less than C2 Radial clearance less than Normal Normal grade of radial internal clearance - not marked Radial internal clearance greater than Normal Radial internal clearance greater than C3 Radial internal clearance greater than C4 Standard clearance for quiet electric motors Special radial internal clearance where * denotes mean figure in m
X26
SPECIAL SPECIFICATION
Dimensionally stabilised for operating temperature of 150C max. Dimensionally stabilised for operating temperature of 200C max. Dimensionally stabilised for operating temperature of 250C max.
Designation Systems
4
NSK
Nominal bore size expressed in 1/8" units. eg. Bore code 5 = 5 x 1/8" units = 5/8".
C1 C2 CN C3 C4 C5 CM CG*
Radial clearance less than C2 Radial clearance less than Normal Normal grade of radial internal clearance - not marked Radial internal clearance greater than Normal Radial internal clearance greater than C3 Radial internal clearance greater than C4 Standard clearance for quiet electric motors Special radial internal clearance where * denotes mean figure in m
Section 1
NSK
7 7 2 10 C T
2 10 C
DIMENSION SERIES
NSK 9 0
ISO 19 10
NSK 2 3
ISO 02 03
BORE CODE
00 01 02 03
CONTACT ANGLE
C A5
15 25
A B
30 40
DU
GROUPING
DB DF DT DU SU
Matched Pair - Back to Back configuration Matched Pair - Face to Face configuration Matched Pair - Tandem configuration Matched Pair - Universal mounting Single Bearing - Universally faced - Can be used DB or DF with 2, 3, 4 etc. rows G Any combination of 2 bearings can be used. Both sides ground for matching. For other possible grouping arrangements see Appendix 3 Page 35
L
PRELOAD
EL C7 or L C8 or M C9 or H CA* CP*
Extra Light Preload Light Preload Medium Preload Heavy Preload Special Axial Clearance Special Axial Preload
X26
SPECIAL SPECIFICATION
Dimensionally stabilised for operating temperature of 150C max. Dimensionally stabilised for operating temperature of 200C max. Dimensionally stabilised for operating temperature of 250C max.
Designation Systems
6
NSK
5 5 2 10
2 10 ZZ X26
TYPE
5 3 Double row angular contact ball bearing - 25 Contact angle Double row angular contact ball bearing - 32 Contact angle
DIMENSION SERIES
NSK 2 3
ISO 02 03
BORE CODE
00 01 02 03
Usually fitted with pressed steel cage with no suffix stated. If suffix is quoted see Appendix 1 Page 32
ZZ X26
Dimensionally stabilised for operating temperature of 150C max. Dimensionally stabilised for operating temperature of 200C max. Dimensionally stabilised for operating temperature of 250C max.
Section 1
NSK
QJ 2 06 X26 QJ 2 06
TYPE
QJ Single row duplex ball bearing - with split inner ring
DIMENSION SERIES
NSK 10 2 3
ISO 10 02 03
BORE CODE
00 01 02 03
Usually fitted with pressed steel cage with no suffix stated. If suffix is quoted see Appendix 1 Page 32
X26
SPECIAL SPECIFICATION
Dimensionally stabilised for operating temperature of 150C max. Dimensionally stabilised for operating temperature of 200C max. Dimensionally stabilised for operating temperature of 250C max.
Designation Systems
8
NSK
N N
2 16 E
K C3 X26
N NU NJ NF NH Single row cylindrical roller bearing - two ribs on inner ring Single row cylindrical roller bearing - two ribs on outer ring Single row cylindrical roller bearing - two ribs on outer ring - one rib on inner Single row cylindrical roller bearing - two ribs on inner ring - one rib on outer Single row cylindrical roller bearing - as NJ type but with additional L shaped thrust collar NUP Single row cylindrical roller bearing - two ribs on outer ring - one rib + one loose rib on inner NU2 Single row cylindrical roller bearing - two ribs on outer ring - Extra wide series NJ2 Single row cylindrical roller bearing - two ribs on outer ring - one rib on inner - Extra wide series NUP2 Single row cylindrical roller bearing - two ribs on outer ring - one rib + one loose rib on inner - Extra wide series NN Double row cylindrical roller bearing - three ribs on inner ring - Extra wide series NNU Double row cylindrical roller bearing - three ribs on outer ring - Extra wide series NSK 19 10 2 00 01 02 03 10mm 12mm 15mm 17mm ISO 19 10 02 NSK 3 4 ISO 03 04
TYPE
2 16 E T K C3
DIMENSION SERIES
BORE CODE
DESIGN FEATURE
CAGE CODES
RING CONFIGURATION
K K30 E1
INTERNAL CLEARANCE
C2 CN C3 C4 C5
Radial clearance less than Normal - marked 0 or C2 Normal grade of radial internal clearance - not marked Radial internal clearance greater than Normal - marked 000 or C3 Radial internal clearance greater than C3 - marked 0000 or C4 Radial internal clearance greater than C4 - marked 00000 or C5
X26
SPECIAL SPECIFICATION
Dimensionally stabilised for operating temperature of 150C max. Dimensionally stabilised for operating temperature of 200C max. Dimensionally stabilised for operating temperature of 250C max.
Section 1
NSK
Designation Format
HR 322 04 CJ
The first 3 digits represent the TYPE CODE and the DIMENSION SERIES.
BORE CODE
00 01 02 03 C D J X
DESIGN FEATURE
Medium angle tapered roller bearing Steep angle tapered roller bearing Outer ring raceway diameter and angle comply with ISO/R355 Dimension Series 20 and 29 - major dimensions comply with ISO/R355
Designation Format
045
T Symbol Representing Tapered Roller Bearing
T 7 F C 045
045
Designation Systems
10
NSK
Designation Format
LM 1 17 49
cone
LL L LM M HM H HH
/ LM 1 17 10
cup
Lighter than Light Light Light Medium Medium Heavy Medium Heavy Heavier than Heavy
LM
DUTY
INCLUDED ANGLE
1 2 3 4 5
6 7 8 9
17
BASIC SERIES
Series 00-19 20-99 000-029 039-129 130-189 190-239 240-289 290-339 340-389 390-429
Basic range in inches 0-1 1-2 1-2 2-3 3-4 4-5 5-6 6-7 7-8 8-9
49
SPECIAL FEATURE
11
Section 1
NSK
2 22 15 CA K E4 C2 S11 -VS 2 22
DIMENSION SERIES TYPE
Type Code 2 - Spherical roller bearing
NSK 30 40 31 41 39
ISO 30 40 31 41 39
NSK 22 32 13 23
ISO 22 32 13 23
15
BORE CODE
For bore code 04 upwards, the general rule is to multiply by 5 to obtain bore size in mm.
The exceptions to this are bearings with bore diameter of 500mm and above. These are denoted by the type and ISO series (230, 239), followed by / and the bore diameter (500mm, 630mm etc.) ie. 230/500, 239/630 etc.
CA
C CA CAM CD H T12
Design with C type pressed steel cage Designed with machined brass cage Designed with machined brass cage Designed with D type pressed steel cage Designed for increased capacity - glass fibre reinforced nylon cage Glass fibre reinforced cage
K E4 C2
RING CONFIGURATION
K K30
E4
Outer ring with oil holes and groove (For H type over 180mm O.D. and other types over 150mm O.D. oil holes and grooves are standard)
INTERNAL CLEARANCE
C1 C2 CN C3 C4 C5 CG*
Radial clearance less than C2 Radial clearance less than Normal Normal grade of radial internal clearance - not marked Radial internal clearance greater than Normal Radial internal clearance greater than C3 Radial internal clearance greater than C4 Special radial internal clearance where * denotes mean figure in m
S11 -VS
S11
-VS
Designation Systems
12
NSK
07
BORE CODE
(last 2 digits in basic number)
00 00 02 03
For bore code 04 upwards, the general rule is to multiply by 5 to obtain bore size in mm. The exception is spherical roller thrust bearings with 500mm bore diameter which are designated 292/500, 293/500 and 294/500. Note that for double direction thrust bearings this diameter is the bore diameter of the two outer washers. The bore diameter of the centre washer is smaller.
M X
CAGE
DESIGN FEATURE
X U P5
Denotes Modified Boundary Dimensions to I.S.O. Denotes with Aligning Seat Washer. Denotes Precision Class 5 (ABEC 5).
13
Section 1
Metric series single and double direction ball and spherical roller thrust bearings
NSK
There are two types of bearing listed under this category. ANGULAR CONTACT THRUST BALL BEARINGS FOR BALL SCREWS Bearings in this category are specially designed to support Precision Ball Screws. The contact angle is 60 and they are usually used in sets of two or more bearings in a preload condition. Bearings are fitted with moulded polyamide cages. A typical designation for this series would be:30TAC62B DF C10 PN7A For more details on this series refer to catalogue Pr. No. A124, Precision Rolling Bearings for Machine Tool Spindles and C912S, Super Precision Bearings - Equivalents Data.
DOUBLE DIRECTION ANGULAR CONTACT THRUST BALL BEARINGS Bearings in this category are specially designed high precision bearings for use in the main spindles of machine tools. Bearings in series 29 and 20 have the same bore and O.D. as the double row cylindrical roller bearings in series NN30 and NN49 respectively and are generally used in conjunction with these roller bearings. Bearings are generally fitted with machined brass cages. Typical designations for this series would be:100TAC20X PN7+L C6 or 140TAC20D PN7+L C6 For more details on this series refer to catalogue Pr. No. A124, Precision Rolling Bearings for Machine Tool Spindles.
Designation Systems
14
NSK
60 1X F 60 5 F 60 5 h J h
J ZZ MC2 P5
No symbol F
BEARING TYPE
BEARING SERIES
BORE DIAMETER
Bore diameter in mm. Bore diameter in mm. where X represents a part millimetre. i.e. 1.5mm.
MATERIAL CODE
No symbol h
J JL W T (Cage
Ribbon cage Ribbon cage (Light Clinched) Crown cage Synthetic resin cage symbols are occasionally omitted)
ZZ MC2
SEALING ARRANGEMENT
INTERNAL CLEARANCE
Radial clearance less than MC2 Radial clearance less than MC3 Normal radial internal clearance Radial internal clearance greater than MC3 Radial internal clearance greater than MC4 Radial internal clearance greater than MC5
P5
No symbol P6
P5 P4
No symbol L
Bearings are sorted into two groups depending on bore tolerance Bearings are sorted into two groups depending on O.D. tolerance Bearings are sorted into four groups depending on bore and O.D. tolerances Grease B32 Beacon 325 PS2 Multemp PS2 (Others available on request)
B32
LUBRICANT CODE
Oil AF2 Aeroshell Fluid 12 A4D Anderol L-401D (Others available on request)
15
Section 1
NSK
Special metric series miniature deep groove ball bearings UC1 B32
MATERIAL CODE
BEARING TYPE
SIZE NUMBER
J JL W T (Cage
Ribbon cage Ribbon cage (Light Clinched) Crown cage Synthetic resin cage symbols are occasionally omitted)
ZZ MC3
SEALING ARRANGMENT
INTERNAL CLEARANCE
Radial clearance less than MC2 Radial clearance less than MC3 Normal radial internal clearance Radial internal clearance greater than MC3 Radial internal clearance greater than MC4 Radial internal clearance greater than MC5
P5
No symbol P6
P5 P4
No symbol L
UC1 B32
Bearings are sorted into two groups depending on bore tolerance Bearings are sorted into two groups depending on O.D. tolerance Bearings are sorted into four groups depending on bore and O.D. tolerances Grease B32 Beacon 325 PS2 Multemp PS2 (Others available on request)
LUBRICANT CODE
Oil AF2 Aeroshell Fluid 12 A4D Anderol L-401D (Others available on request)
Designation Systems
16
NSK
ZZ MC3
No symbol S
B32
Bearing steel (SUJ2) Stainless steel (SUS440C)
MATERIAL CODE
BEARING TYPE
R Inch series deep groove ball bearing FR Inch series deep groove ball bearing with flanged O.D. RW Inch series deep groove ball with extended inner ring
SIZE NUMBER
J JL W T (Cage
Ribbon cage Ribbon cage (Light Clinched) Crown cage Synthetic resin cage symbols are occasionally omitted)
ZZS MC4
SEALING ARRANGEMENT
INTERNAL CLEARANCE
Radial clearance less than MC2 Radial clearance less than MC3 Normal radial internal clearance Radial internal clearance greater than MC3 Radial internal clearance greater than MC4 Radial internal clearance greater than MC5
7P L UC3 AF2
No symbol 3
ABEC 1 ABEC 3
5P 7P
ABEC 5P ABEC 7P
No symbol L
Bearings are sorted into two groups depending on bore tolerance Bearings are sorted into two groups depending on O.D. tolerance Bearings are sorted into four groups depending on bore and O.D. tolerances Grease B32 Beacon 325 PS2 Multemp PS2 (Others available on request)
LUBRICANT CODE
Oil AF2 Aeroshell Fluid 12 A4D Anderol L-401D (Others available on request)
17
Section 1
Designation Systems
18
6 6
2 10 K RS J C2 LOC P6 S*
6 16 98 E L M 4 1 2 NSK 18 19 0 3 4 5 7 6 7 8 9 10 12 13 15 17 20 3mm (Magneto 4mm (Magneto 5mm 7mm 6mm 7mm 8mm 9mm 10mm (Magneto 12mm (Magneto 13mm (Magneto 15mm (Magneto 17mm (Magneto 20mm (Magneto Single row radial ball bearing Single row radial ball bearing - narrow, extra light series Single row radial ball bearing - narrow light series Magneto bearings (For NSK brand see Radial Ball Bearings Page 4) Magneto bearings (For NSK brand see Radial Ball Bearings Page 4) Single row radial ball bearing - with filling slots and maximum load capacity Double row radial ball bearing Double row radial ball bearing - self-aligning Double row radial ball bearing - self-aligning; wide series ISO 18 19 10 type) type) NSK 2 3 4 00 01 02 03 10mm 12mm 15mm 17mm (except (except (except (except ISO 02 03 04 Magneto) Magneto) Magneto) Magneto)
TYPE
2 10
DIMENSION SERIES
BORE CODE
For bore code 04 upwards, the general rule is to multiply by 5 to obtain bore size in mm. type) type) type) type) type) type)
K RS J C2
SEALING ARRANGEMENT CAGE TYPE CODE
INTERNAL CLEARANCE
C2 CN C3 C4 C5 R*
Radial clearance less than Normal - marked 0 or C2 Normal grade of radial internal clearance - not marked Radial internal clearance greater than Normal - marked 000 or C3 Radial internal clearance greater than C3 marked 0000 or C4 Radial internal clearance greater than C4 marked 00000 or C5 Special radial internal clearance (* denotes mean figure in m)
LOC P6
SPECIAL FEATURE
LOC
PRECISION GRADE
Electric standard Precision grade dedicated to Inch series bearings ABEC1 tolerances Electric Motor Bearing tolerances (ISO Tolerance class 6) and special radial internal clearances Motor Traction Specification (PDS Q28) Operational temperature Up to 200C max. Up to 250C max. Up to 300C max. Up to 350C max.
S*
HEAT STABILISED
Where * gives the Specification number
Specification number 1 2 3 4
19
Section 2
RHP
LJ 4 LJ
TYPE
BORE CODE
4E
K RS J C2
INTERNAL CLEARANCE
C2 CN C3 C4 C5 R*
Radial clearance less than Normal - marked 0 or C2 Normal grade of radial internal clearance - not marked Radial internal clearance greater than Normal - marked 000 or C3 Radial internal clearance greater than C3 marked 0000 or C4 Radial internal clearance greater than C4 marked 00000 or C5 Special radial internal clearance (* denotes mean figure in m)
LOC EP
SPECIAL FEATURE
LOC
PRECISION GRADE
Electric standard Precision grade dedicated to Inch series bearings ABEC1 tolerances Electric Motor Bearing tolerances (ISO Tolerance class 6) and special radial internal clearances Motor Traction Specification (PDS Q28)
Designation Systems
20
RHP
7 7 2 10
2 10 B
DIMENSION SERIES
00 01 02 03
BORE CODE
For bore code 04 upwards, the general rule is to multiply by 5 to obtain bore size in mm.
B E TN DU
CONTACT ANGLE
New ref C G E
New ref A B
Old ref X4 X6
Angle 30 40
GROUPING
(Most used)
DB Matched Pair - Back to Back configuration DF Matched Pair - Face to Face configuration DT Matched Pair - Tandem configuration DU Matched Pair - Universal mounting SU Single Bearing - Universally faced For other possible grouping arrangements see Appendix 3 Page 35 F L M H S U UX A* P* ELEC EP EP1 P6E Flush Faced Light Preload Medium Preload Heavy Preload Standard Axial Clearance Universally faced Single Bearing to give Standard Axial Clearance when mounted in pairs Universally faced single bearing to give an Axial Clearance less than Standard Axial Clearance when mounted in pairs. Special Axial Clearance (*Denotes mean figure in m.) Special Axial Preload (*Denotes mean figure in m.) Electric standard Precision grade dedicated to Inch series bearings ABEC1 tolerances Electric Motor Bearing tolerances (ISO Tolerance class 6) and special radial internal clearances.
M
PRELOAD
P6
PRECISION GRADE
21
Section 2
RHP
LJT LJT 4
BORE CODE
4E
X2 M DU L
CONTACT ANGLE
X2 G X4
15 20 30
GROUPING
(Most used)
DB DF DT DU L M H S U UX A* P*
Back to Back configuration Face to Face configuration Tandem configuration Universal mounting
PRELOAD
Light Preload Medium Preload Heavy Preload Standard Axial Clearance Universally faced Single Bearing to give Standard Axial Clearance when mounted in pairs Universally faced single bearing to give an Axial Clearance less than Standard Axial Clearance when mounted in pairs. Special Axial Clearance eg. DBA138 (*Denotes mean figure in m.) Special Axial Preload eg. DBP18 (*Denotes mean figure in m.)
EP
PRECISION GRADE
G
Electric standard Precision grade dedicated to Inch series bearings ABEC1 tolerances Electric Motor Bearing tolerances (ISO Tolerance class 6) and special radial internal clearances.
Designation Systems
22
RHP
3 3
2 10 ZR J C2
3 3_B LDJK Double row angular contact ball - contact angles diverge - 32 Double row angular contact ball - contact angles diverge - 25 Double row angular contact ball - contact angles converge - 30 Double row angular contact ball - contact angles converge - 30 Double row angular contact ball - contact angles converge - 30 Double row angular contact ball - Light series - 30 Double row angular contact ball - Medium series - 30 bearing - filling slots bearing - no filling slots bearing - no filling slots bearing - no filling slots bearing - no filling slots bearing - with split outer ring bearing - with split outer ring
TYPE
2 10 ZR J C2
DIMENSION SERIES
RHP 10 2
ISO 10 02
RHP 3 4
ISO 03 04
BORE CODE
00 01 02 03
INTERNAL CLEARANCE
C2 CN C3 C4 A* P*
Radial clearance less than Normal - marked 0 or C2 Normal grade of radial internal clearance - not marked Radial internal clearance greater than Normal - marked 000 or C3 Radial internal clearance greater than C3 marked 0000 or C4 Special radial internal clearance (* denotes mean figure in m) Special axial preload. (* denotes mean figure in m)
23
Section 2
RHP
QJ 2 10 NR MB C3 LOC QJ 2 10
TYPE
QJ
DIMENSION SERIES
RHP 2 3
ISO 02 03
BORE CODE
00 01 02 03
QJL QJL 4
4 NR MB C3 LOC
TYPE
QJL QJM
BORE CODE
4E
The bore code shall be numeric and comprise the nominal bore as fractions and integers ie. 1/2; 2; 3.1/2 etc. E was used to denote inch series bearings with 4 inches bore and over. Now only used when there is no other distinguishing symbol within a bearing designation.
NR MB C3 LOC
C3 A*
Axial clearance greater than Normal - marked 000 or C3 Special axial clearance (* denotes mean figure in m)
LOC
Designation Systems
24
RHP
512 07 J 512 07
BORE CODE
(last 2 digits in basic number)
00 01 02 03
LT 1.1/2 B LT 1.1/2
J
FT XLT LT or MT
BORE CODE
The bore code shall be numeric and comprise the nominal bore as fractions and integers ie. 1/2; 2; 3.1/2 etc.
B E J
CAGE TYPE CODE
Used only with LT series bearings up to 1.7/8 inch bore. Refers to bearings with one large bore washer and one small bore washer.
Was used to denote inch series bearings with 4 inches bore and over. Now only used when there is no other distinguishing symbol within a bearing designation.
25
Section 2
RHP
N N
2 16 E
TYPE
2 16 E K NR M P6 C2
DIMENSION SERIES
BORE CODE
DESIGN FEATURE
Higher Radial Load Rating Higher Load Rating plus Improved internal design feature giving greater axial load carrying capability. Note: All standard products will be with interchangeable rings and P6 tolerances.
Tapered bore 1 : 12
P6
PRECISION GRADE
X T C2 CN C3 C4 C5 R*
ABEC 3 Tolerances or ISO Tolerance Class 6 (Used for some current production in conjunction with interchangeable rings) Same as for P6 above but only used for bearings with outside diameter greater than 110mm. Motor Traction Specification (PDS Q28) Radial clearance less than Normal - marked 0 or C2 Normal grade of radial internal clearance - not marked or marked CN Radial internal clearance greater than Normal - marked 000 or C3 Radial internal clearance greater than C3 - marked 0000 or C4 Radial internal clearance greater than C4 - marked 00000 or C5 Special radial internal clearance where * denotes mean figure in m
INTERNAL CLEARANCE
Designation Systems
26
RHP
LRJ 4 LRJ
TYPE
BORE CODE
4E
K NR M C2
Tapered bore 1 : 12
INTERNAL CLEARANCE
C2 CN C3 C4 C5 R*
Radial clearance less than Normal - marked 0 or C2 Normal grade of radial internal clearance - not marked or marked CN Radial internal clearance greater than Normal - marked 000 or C3 Radial internal clearance greater than C3 - marked 0000 or C4 Radial internal clearance greater than C4 - marked 00000 or C5 Special radial internal clearance (* denotes mean figure in m)
EP
PRECISION GRADE
"Electric" standard Precision grade dedicated to Inch series bearings ABEC1 tolerances Electric Motor Bearing tolerances (ISO Tolerance class 6) and special radial internal clearances Motor Traction Specification (PDS Q28)
27
Section 2
RHP
2 2 22
M W33 C3 U22 R*
Type Code 2 - Spherical roller bearing
DIMENSION SERIES
Digits 2 and 3 represent the ISO DIMENSION SERIES as described below. RHP ISO RHP ISO 30 30 22 22 40 40 32 32 31 31 13 13 41 41 23 23 Digits 4 and 5 combined represent the BORE CODE. The BORE CODE multiplied by 5 results in the bore size in mm. eg. Bore Code = 15; Bore Diameter = 15 x 5 = 75mm.
15 E X1 K M
X1 X2
Tapered bore 1 : 12
CAGE CODES
For E-type bearings No suffix - Two piece Polyamide cage - TN type M - 1-piece rolling element centred machined brass cage J - 2-piece rolling element centred pressed steel cage For non-E-type bearings J - 2-piece rolling pressed steel cage (1-piece pressed steel for 213 series) M - 2-piece rolling element centred brass cage M - 1-piece outer ring centred brass cage for 213 series MB - 2-piece or 1-piece inner ring centred brass cage MA - 2-piece outer ring centred brass cage W33 E5 E7 C2 CN C3 C4 C5 Lubrication holes and grooves in outer ring Lubrication holes and grooves in inner ring E5 + W33 Radial clearance less than Normal - marked C2 Normal grade of radial internal clearance - marked CN Radial internal clearance greater than Normal - marked C3 Radial internal clearance greater than C3 - marked C4 Radial internal clearance greater than C4 - marked C5 (Not used if R* or R*/ * is included to denote a special internal clearance)
W33 C3 U22 R*
Special radial internal clearance (* denotes mean figure in m) Not used if C2; CN etc. specifies a catalogue clearances) Note: R*/ * may appear on bearings already in use where */ * represent max. and min. values in m.
R*
Bearings with tapered bores can be supplied with adapter sleeve, locking nut and washer (designated H----). Typical designations for bearing with adapter sleeve would be 22212K + H312 or 22312K + H312.
Designation Systems
28
RHP
Metric series double row spherical roller bearings for use in vibratory equipment K VB C4
TYPE
Type Code 2 - Spherical roller bearing
2 23 26 E 2 23
DIMENSION SERIES
Digits 2 and 3 represent the ISO DIMENSION SERIES as described below. RHP ISO 21 21 22 22 23 23 Digits 4 and 5 combined represent the BORE CODE. The BORE CODE multiplied by 5 results in the bore size in mm. eg. Bore Code = 26; Bore Diameter = 26 x 5 = 130mm.
26 E K VB
BORE CODE
DESIGN FEATURE
TAPERED BORE
Tapered bore 1 : 12
CAPABILITY FEATURE
VB Vibratory application specification which covers these features: 1-piece rolling element centred machined brass cage Outer ring has lubricating holes with interconnecting groove on O.D. (as W33) C4 Radial internal clearance greater than C3 and with reduced tolerance band *Note: (C4 Radial internal clearance with reduced tolerance band supplied as standard) C4 If not CN C3 Standard - see Note above* Standard Normal grade of radial internal clearance with reduced tolerance band Radial internal clearance greater than Normal and with reduced tolerance band
C4
INTERNAL CLEARANCE
29
Section 2
RHP
Light series externally aligning ball bearing with seating ring. Medium series externally aligning ball bearing with seating ring. Light series externally aligning ball bearing in wide aligning housing with end covers. Medium series externally aligning ball bearing in wide aligning housing with end covers. Light series externally aligning ball bearing in wide aligning housing with end covers and tapered bore adapter sleeve. Medium series externally aligning ball bearing in wide aligning housing with end covers and tapered bore adapter sleeve.
RLSN
RLSN
Light series externally aligning roller bearing with seating ring. Two ribs on each ring. RLSN-E Light series externally aligning roller bearing with seating ring. Two ribs on outer and parallel inner ring. RMSN Medium series externally aligning roller bearing with seating ring. Two ribs on each ring. RMSN-E Medium series externally aligning roller bearing with seating ring. Two ribs on outer and parallel inner ring. RLSW Light series externally aligning roller bearing in wide aligning housing with end covers. RMSW Medium series externally aligning roller bearing in wide aligning housing with end covers. RLTW Light series externally aligning roller bearing in wide aligning housing with end covers and tapered bore adapter sleeve. RMTW Medium series externally aligning roller bearing in wide aligning housing with end covers and tapered bore adapter sleeve.
10 C2
BORE CODE
The bore code is simply a numeric sequence which is given as integers and fractions ie. 7; 12.1/2; 21 etc. The reference does not represent the bore size in either inch or metric size.
INTERNAL CLEARANCE
C2 Radial clearance less than Normal - marked 0 or C2 CN Normal grade of radial internal clearance - not marked or marked CN C3 Radial internal clearance greater than Normal - marked 000 or C3 C4 Radial internal clearance greater than C3 - marked 0000 or C4 Note: The standard RIC for ball bearings with cylindrical bore is CN. Ball bearings with tapered bore and all cylindrical roller bearings are supplied with C3 clearance. The bearing clearance grade is only marked on the bearing outer ring when fits differ from the above standard fits.
Note: The ball bearings are fitted with steel (J) cages up to 6" bore (Light series) and 5.1/2" bore size (Medium series). Above these sizes the standard ball bearing cages are machined brass. For all roller bearings the standard cages are machined brass (M or MB).
Designation Systems
30
Appendices
Manual Appendix Page No. Number
32 33 34 35 2 3 1
Sheet No.
1 2 1 1 Cage Type Codes for NSK and RHP Products Cage Type Codes for NSK and RHP Products Standard Variant Codes for NSK and RHP Products Mounting Configuration Codes for NSK and RHP Single Row Angular Contact Ball Bearings
31
Appendix 1 Sheet 1 of 2
NSK Suffix C, CD CAM F RHP Suffix Definition
F FA FAS FB FBS FNA FNB FP H H J JC JC JH JN JP JW L LA LAS LB LAB LNA LNB M MA MAS MB MB MBS MNA MNB MR T T T T TA TNA TB TNB TL TN TNH
J JB
JW
M MA
TNG TY T12 V
V VB VH VM VMP
W WS Y Y YC
Steel cage for Spherical Roller Bearings 1 - Piece Brass Cage for Spherical Roller Bearing 2 - Piece Machined Steel Cage 1 - Piece, or 2 - Piece Riveted, Rolling Element Centred Machined Steel Cage 1 - Piece Outer Ring Centred Machined Steel Cage 1 - Piece Outer Ring Centred Machined Steel Cage with Lubrication Groove in Locating Surface 1 - Piece Inner Ring Centred Machined Steel Cage 1 - Piece Inner Ring Centred Machined Steel Cage with Lubrication Groove in Locating Surface 2 - Piece Riveted Outer Ring Centred Machined Steel Cage 2 - Piece Riveted Inner ring Centred Machined Steel Cage 1 - Piece Rolling Element Centred Machined Steel Cage Polyamide Cage for Spherical Roller Bearings Pressed Steel Cage for Spherical Thrust Roller Bearing 1 - Piece, or 2 - Piece Riveted, Rolling Element Centred Pressed Steel Cage 1 - Piece Inner Ring Centred Pressed Steel Cage 2 - Piece Pressed Cage for Quiet Applications (Single Row Radial Ball Bearings) 2 - Piece Rolling Element Centred Pressed Steel Cleated (Claw) Cage 1 - Piece Rolling Element Centred Pressed Steel Snap-on Type Cage Multi Piece Rolling Element Centred Pressed Steel Cage with Spacer Segments 1 - Piece Rolling Element Centred Pressed Steel Window Type Cage 2 - Piece Rolling Element Centred Pressed Steel Welded Cage Machined Light Alloy Cage 1 - Piece Outer Ring Centred Machined Light Metal Alloy Cage 1 - Piece Outer Ring Centred Machined Light Metal Alloy Cage with Lubrication Groove in Locating Surface 1 - Piece Inner Ring Centred Machined Light Metal Alloy Cage 1 - Piece Inner Ring Centred Machined Light Metal Alloy Cage with Lubrication Groove in Locating Surface 2 - Piece Riveted Outer Ring Centred Machined Light Metal Alloy Cage 2 - Piece Riveted Inner Ring Centred Machined Light Metal Alloy Cage 1 - Piece, or 2 - Piece Riveted, Rolling Element Centred Machined Brass Cage Rivetless Brass Cage with Bent Tabs (Single Row Radial Roller Bearings) 1 - Piece Outer Ring Centred Machined Brass Cage 1 - Piece Outer Ring Centred Machined Brass Cage with Lubrication Groove in Locating Surface Split Crown Type Machined Brass Cage (Double Row Roller Bearings) 1 - Piece Inner Ring Centred Machined Brass Cage 1 - Piece Inner Ring Centred Machined Brass Cage with Lubrication Groove in Locating Surface 2 - Piece Riveted Outer Ring Centred Machined Brass Cage 2 - Piece Riveted Inner Ring Centred Machined Brass Cage 2 - Piece Roller Guided Brass Cage (Single Row Roller Bearings) Machined Laminated Phenolic Cage (Single Row Radial or A. C. Bearings) Glass Fibre Reinforced Nylon Cage (Radial Roller Bearings) 1 - Piece Outer Ring Centred Machined Laminated Phenolic Cage 2 - Piece Riveted Outer Ring Centred Machined Laminated Phenolic Cage 1 - Piece Inner Ring Centred Machined Laminated Phenolic cage 1 - Piece, or 2 - Piece Riveted, Inner Ring Centred Machined Laminated Phenolic Cage Self Lubricating Cage 1 - Piece Moulded Polyamide Cage 1 - Piece Rolling Element Centred Snap-on Type Moulded Polyamide Cage Polyamide Cage for Double Row Conrad Type Bearing Glass Fibre Reinforced Nylon Cage (Angular Contact Type Bearings) Glass Fibre Reinforced Nylon Cage (Ball Journal, Taper Roller and Spherical Roller Bearings) No Cage (Full Complement) 1 - Piece Rolling Element Centred Machined Brass Cage - Spherical Roller Bearing for Vibratory Equipment No Cage - Full Complement of Rollers Self Retained 2 - Piece Riveted Rolling Element Centred Machined Brass Cage 2 - Piece Rolling Element Centred Machined Brass Cage - Upset Cage Bar to Retain Cage Cap. High Complement Rolling Element One Piece Pressed Cage Pressed Steel Cage for E Type High Capacity Roller Bearing Pressed Brass Cage 1 - Piece Rolling Element Centred Snap-on Type Pressed Brass Cage 2 - Piece Rolling Element Centred Pressed Brass Cleated (Claw) Type Cage
Designation Systems
32
Appendix 1 Sheet 2 of 2
Omission of Cage Symbol Cage Type Ball Bearing
O Indicates when the Cage Ref. may be omitted (NSK products only) J O JW O W Y M O O O O O O O O*
Roller Bearing
Single row radial Single row angular contact Double row radial Double row angular contact Self aligning Thrust Magneto Tapered Cylindrical *But 02, 03, 04, 22 and 23 must carry M symbol
33
Appendix 2 Sheet 1 of 1
NSK Suffix N NX NR Z ZZ ZS ZZS ZN ZNR NZ NRZ RS/D/DU 2RS/DD/DDU DW DDW TS TTS V VV RHP Suffix N NR Z ZR -2Z Variant
-2ZR ZN ZRN ZNR ZRNR ZNB ZRNB ZNBR ZRNBR RS RSR -2RS
-2RSR RSN RSRN RSNR RSRNR RSNB RSRNB RSNBR RSRNBR RSZ RSRZ RSZN RSRZN RSZNR RSRZNR RSZNB RSRZNB RSZNBR RSRZNBR
Snap ring groove Special snap ring groove dimensions (i.e. NX1, NX2 etc for different special ring groove dimensions) Snap ring groove and snap ring Single shield Single shield - parallel O/dia. inner Doubled shielded Single shield (Retained by circlip in outer ring - usually for miniature ball bearings) Double shield (Retained by circlip in outer ring - usually for miniature ball bearings) Double shielded - parallel O/dia. inner Single shield with snap ring groove on opposite side to shield Single shield - parallel O/dia. inner ring - with snap ring groove on opposite side to shield Single shield with snap ring groove and snap ring on opposite side to shield Single shield - parallel O/dia. inner ring - with snap ring groove and snap ring on opposite side to shield Single shield with snap ring groove on same side as shield Single shield - parallel O/dia. inner ring - snap ring groove on same side as shield Single shield - snap ring groove and snap ring on same side as shield Single shield - parallel O/dia. inner ring - with snap ring groove and snap ring on same side as shield Single seal Single seal - parallel O/dia. inner ring Double sealed Single light contact seal - small bore metric radial ball bearings Double light contact seal - small bore metric radial ball bearings Single contact type Teflon seal - usually for miniature ball bearings Double contact type Teflon seal - usually for miniature ball bearings Single sealed with removable rubber non-contact type seal Double sealed with removable rubber non-contact type seal Double sealed - parallel O/dia. inner ring Single seal with snap ring groove on opposite side to seal Single seal - parallel O/dia. inner ring - with snap ring groove on opposite side to seal Single seal with snap ring groove and snap ring on opposite side to seal Single seal - parallel O/dia. inner ring - with snap ring groove and snap ring on opposite side to seal Single seal with snap ring groove on same side as seal Single seal - parallel O/dia. inner ring - with snap ring groove on same side as seal Single seal with snap ring groove and snap ring on same side as seal Single seal - parallel O/dia. inner ring - with snap ring groove and snap ring on same side as seal Single seal, single shield Single seal - parallel O/dia. inner ring - and single shield Single seal, single shield with snap ring groove on same side as shield Single seal - parallel O/dia. inner ring - single shield with snap ring groove on same side as shield Single seal, single shield with snap ring groove and snap ring on same side as shield Single seal - parallel O/dia. inner ring - single shield with snap ring groove and snap ring on same side as shield Single seal, single shield with snap ring groove on same side as seal Single seal - parallel O/dia. inner ring - single shield with snap ring groove on same side as seal Single seal, single shield with snap ring groove and snap ring on same side as seal Single seal - parallel O/dia. inner ring - single shield with snap ring groove and snap ring on same side as seal
DU* DDU V* VV* type seals (Where * represents a numeric suffix) Suffix Definition 2 DU type seal without air vent 5 DU and V type seals made from Buna N material 7 DU and V type Viton seal 8 DU and V type Polyacrylic seal 9 DU and V type seal made from Silicone rubber 28 DU type seal made from Acryl Ester rubber without air vents
Designation Systems
34
Appendix 3 Sheet 1 of 1
NSK Suffix DB DF DT DBD DFD DTD DBB DFF DTT DBT DFT SU DU G DR RHP Suffix DB DF DT 2TB 2TF 3T QB QF 4T 3TB 3TF SU DU U D Configuration
Mounting configurations for NSK and RHP single row angular contact ball bearings
Matched pair - Back to Back configuration Matched pair - Face to Face configuration Matched pair - Tandem configuration Matched set of 3 - Tandem pair mounted Back to Back with a Single bearing Matched set of 3 - Tandem pair mounted Face to Face with a Single bearing Matched set of 3 bearings mounted in Tandem configuration Matched set of 4 - Tandem pair mounted Back to Back with Tandem pair Matched set of 4 - Tandem pair mounted Face to Face with Tandem pair Matched set of 4 bearings mounted in Tandem configuration Matched set of 4 - 3 bearings in Tandem mounted Back to Back with a Single bearing Matched set of 4 - 3 bearings in Tandem mounted Face to Face with a Single bearing Single bearing Universally faced for use in multiple sets mounted in any configuration Universally faced pair of identical bearings for use in DB, DF or DT configuration Any combination of 2 bearings can be used. (Both sides are ground for matching) 2 bearings mounted side by side but with no face control
35
Designation Systems
36
DU M
P4
Normal range Small ball EXCEL range BETN range Flanged type range Double counterbore type
CONSTRUCTION
7 0 10
TYPE
DIMENSION SERIES
RHP 9 0 00 01 02 03 G R S C G E T/ET M L G A B SU DU, DB, DF, DT 3U, 3T, 2TB, 2TF 3TB, 3TF QB, QF, QU S - Slack F - Flush X - Extra light L - Light 10mm 12mm 15mm 17mm
ISO 19 10
RHP 2 3
ISO 02 03
BORE CODE
CONSTRUCTION
Normal type Reverse type Ceramic ball type 15 20 25 Phenolic resin Brass Aluminium A B 30 40
C T
CONTACT ANGLE
TN/TNH/ETN
Polyamide
CAGE MATERIAL
LOCATION
Outer ring guided Phenolic cages Outer ring guided cages except Phenolic Inner ring guided Single universal Paired unit Triple set Quad set Quad set M - Medium H - Heavy G** - Special Preload A** - Special axial clearance
DU M
GROUPING
K5
P4
PRECISION GRADE
RHP P0 P6 P5 P4 P3 P2
SPECIAL REQUIREMENTS
G **
Denotes mean figure in m
37
Section 3
RHP
6 6 0 10
0 10
CN P4
6 Single row radial ball bearing
DIMENSION SERIES
RHP 9 0
ISO 19 10
RHP 2 3
ISO 02 03
BORE CODE
00 01 02 03
G S
Single shield Double shield Single seal Double seal Phenolic resin Brass Aluminium Polyamide
T B CN
CAGE MATERIAL
LOCATION
A B BH Standard R.I.C.
Outer ring guided Inner ring guided Inner ring guided C1 CN C2 C3 C4 R** A**
INTERNAL CLEARANCE
Special R.I.C. Special Axial Clearance
P4
PRECISION GRADE
RHP P0 P6 P5 P4 P3 P2
SPECIAL REQUIREMENTS
G **
Denotes mean figure in m
Designation Systems
38
RHP
BSB BSB
DU
M
BSB BSCU BSPB
P3
Ballscrew support bearing Cartridge unit Pillow block unit
DIMENSION SERIES
ISO Non ISO 02 03 RHP INCH Nom size in 100ths of an inch e.g. 150 = 1.1/2 RHP INCH G
062 DU M
RHP METRIC Size in mm. (Except for I.S.O. Series) Housing diameter in mm. Base to bore centreline height in mm. SU DU, DB, DF, DT 3U, 3T, 2TB, 2TF 3TB, 3TF QB, QF, QU RHP L M H H G** Single universal Paired unit Triple set Quad set Quad set
GROUPING
PRELOAD
LEVEL Light - Metric series Medium - Metric series Heavy - Metric series Standard Preload - Inch Series Special Preload
SPECIAL PRECISION
K5
P3
PRECISION GRADE
G **
39
Section 3
RHP
N 10 16 M C1 P5 N 10 16 M
CAGE CODES TYPE
N NU Single row cylindrical roller bearing - two ribs on inner, plain outer - two ribs on outer, plain inner
DIMENSION SERIES
ISO 19 10
RHP 2 3
ISO 02 03
BORE CODE
M MA MB MNB J
Machined brass locate rolling elements Machined brass locate bore of outer ring Machined brass locate O.D. of inner ring Machined brass - 2 piece riveted - located on O.D. of inner ring Pressed steel located on rolling elements
C1
Standard R.I.C.
INTERNAL CLEARANCE
Special R.I.C.
C1 CN C2 C3 C4 R**
P5
PRECISION GRADE
**
Denotes mean figure in m
RHP P5
ISO Class 5
ABEC 5
Designation Systems
40
RHP
NN 30 10 K TN SP W33 C1 NN 30 10 K TN SP W33 C1
TYPE
Double row roller bearing
DIMENSION SERIES
RHP 30
ISO 30
BORE CODE
00 01 02 03
CONSTRUCTION FEATURE CAGE MATERIAL AND LOCATION PRECISION GRADE CONSTRUCTION FEATURE INTERNAL CLEARANCE
Tapered bore
SP UP
Standard R.I.C.
C1 C2
41
Section 3
Designation Systems
42
UC P UC P 2 09
HOUSING TYPE
P/IP/PH/PA/EP/LP - Cast Iron Pillow Block Units F/FC/FS/FL/FA/FK - Cast Iron Flanged Units PF/PFL/PP - Pressed Steel Housing T/C/RP/PPR/LF/EH/BF - Misc.
00 01 02 03
-26S
Imperial Bore Diameter 1/2" to 4" inclusive denoted in 1/16" units (e.g. Bore Code 26 = 26/16 = 1.625 = 1.5/8" Bore)
43
Section 4
THE LETTER R IS INCLUDED AFTER THE BORE CODE WHEN THE UNITS ARE MADE IN THE RHP FACTORIES (eg. UCP209R-26S)
NSK
UC 2 08 -24S UC 2 08
INSERT TYPE
UC/UB - Set Screw Lock EW/EN - Eccentric Collar Lock UK - Taper Sleeve Lock
00 01 02 03
NOTE - If metric bore then the information below is not applicable THE LETTER R IS INCLUDED AFTER THE BORE CODE WHEN THE UNITS ARE MADE IN THE RHP FACTORIES (eg. UCP208R-24S)
-24S
Imperial Bore Diameter 1/2" to 4" inclusive denoted in 1/16" units (e.g. Bore Code 24 = 24/16 = 1.50 = 1.1/2" Bore)
Designation Systems
44
J NP 45 DEC FS J NP
PREFIX CHARACTER
T J No Prefix - Standard Product - Triple Lip Seal - Reverse Outer Ring Assembly (ie. Outer Ring Grease Groove same side as Locking End of Inner Ring)
HOUSING TYPE
NP/SL/MP/CNP/SNP - Cast Iron Pillow Block Units SF/MSF/MSFT/LFTC/FC/MFC - Cast Iron Flanged Units ST/MST - Cast Iron Take Up Units BT/SLC/MSC/SCHB/SCH - Misc. Units SLFE/SLFT/SLFL/LPB/LPBR - Pressed Steel Housings
45 DEC FS
Metric Bore Diameter 12 to 100 inclusive denoted in mm. Imperial Bore Diameter 1/2" to 4" inclusive denoted in inches No character - Set Screw Lock - Long Inner Ring - Set Screw Lock - Short inner ring - Eccentric collar lock with long inner ring - Eccentric collar lock with short inner ring
A DEC EC
SUFFIX CHARACTERS
(Only the main ones listed)
J - METAL CAGE FITTED MS44 - High temperature insert (+ 150 C max.) - D4M marked on box MS33 - High temperature insert (-55 C min.) - D3M marked on box FS - FLINGER SEALS FITTED 2Z - SHIELDS FITTED L - Larger than normal unit fitted for the basic bore size R - Smaller than normal unit fitted for the basic bore size Note: A combination of suffix characters may apply (eg. 2ZFS)
45
Section 5
RHP
Standard Taper Lock Self-Lube bearing units with sleeve assembly fitted - 1.1/2 K
HOUSING TYPE
NP/MP - Cast Iron Pillow Block Units MSF/MSFT - Cast Iron Flanged Units
NP 10 45 NP 10 45 1.1/2 K
OUTER RING TYPE BASIC GROUP INDICATOR SEPARATING DIGIT NOMINAL BORE DIAMETER
(Imperial & Metric)
10 -
25 to 55 inclusive
Metric Bore Diameter 20 to 50 inclusive denoted in mm. Imperial Bore Diameter 3/4" to 2" inclusive denoted in inches
Designation Systems
46
RHP
NP 10 45 K NP 10 45 K
HOUSING TYPE
NP/MP - Cast Iron Pillow Block Units MSF/MSFT - Cast Iron Flanged Units
10
25 to 55 inclusive
Tapered bore 1 : 12
47
Section 5
RHP
T 10 45 T 10
J
No Prefix - Standard Product - Triple Lip Seal - Reverse Outer Ring Assembly (ie. Outer Ring Grease Groove same side as Locking End of Inner Ring)
10 to 16 inclusive (Even Numbers only) Light Series - Outer Ring Spherical O.D. 11 to 17 inclusive (Odd Numbers only) Light Series - Outer Ring Parallel O.D. 22 - Extra Light Type - Outer Ring Spherical O.D. 23 - Extra Light Type - Outer Ring Parallel O.D. 30 - Medium Series - Outer Ring Spherical O.D. 31 - Medium Series - Outer Ring Parallel O.D.
45 1.5/8 DEC G J
17 to 95 inclusive
Metric Bore Diameter 12 to 95 inclusive denoted in mm. Imperial Bore Diameter 1/2" to 4 inclusive denoted in inches
SHAFT LOCKING TYPE & INNER RING LENGTH INDICATOR LUBRICATION FACILITY
DEC EC
No character - Set Screw Lock - Eccentric collar lock with long inner ring - Eccentric collar lock with short inner ring
SUFFIX CHARACTERS
(Only the main ones listed)
J - Metal cage fitted MS44 - High temperature insert (+ 150 C max.) - D4M marked on box MS33 - High temperature insert (-55 C min.) - D3M marked on box FS - Flinger seals fitted 2Z - Shields fitted L - Larger than normal unit fitted for the basic bore size R - Smaller than normal unit fitted for the basic bore size Note: A combination of suffix characters may apply (eg. 2ZFS)
Designation Systems
48
RHP
10 25 10 25 20 K G
OUTER RING TYPE BASIC GROUP INDICATOR SEPARATING DIGIT NOMINAL BORE DIAMETER
(Imperial & Metric)
25 to 55 inclusive
Metric Bore Diameter 20 to 50 inclusive denoted in mm. Imperial Bore Diameter 3/4" to 2" inclusive denoted in inches
LUBRICATION FACILITY
49
Section 5
RHP
10 25 K G 10 25 K G
LUBRICATION FACILITY OUTER RING TYPE BASIC GROUP INDICATOR
10 11 - Light Series - Outer Ring Spherical O.D. - Light Series - Outer Ring Parallel O.D.
25 to 55 inclusive
Tapered bore 1 : 12
Designation Systems
50
RHP
25 P 25 P
BASIC GROUP INDICATOR
20 to 60 inclusive
Identifies Protection
51
Section 5
Designation Systems
52
P NP 25 CR P NP 25 CR
PREFIX CHARACTER HOUSING TYPE NOMINAL BORE DIAMETER
(Imperial & Metric)
P - Identifies Plastic Housing
NP - Pillow Block Units SF - Four Bolt Flanged Units SFT - Two Bolt Flanged Units
Metric Bore Diameter 20 to 35 inclusive denoted in mm. Imperial Bore Diameter 3/4" to 1.7/16" inclusive denoted in inches
SUFFIX CHARACTERS
53
Section 6
RHP
J 10 25 J 10 25 25 G CR
10 -
20 to 35 inclusive
Metric Bore Diameter 20 to 35 inclusive denoted in mm. Imperial Bore Diameter 3/4" to 1.7/16" inclusive denoted in inches
Designation Systems
54
RHP
P 25 P P 25 P
PREFIX CHARACTER BASIC GROUP INDICATOR SUFFIX CHARACTER
P - Identifies Plastic End Cover
20 to 35 inclusive
- Identifies Protection
55
Section 6
Designation Systems
56
PD NF 1 40 PD NF 1 40 1.1/2
OUTER RING WIDTH OUTER RING O.D. FORM INNER RING WIDTH BASIC GROUP INDICATOR SEPARATING DIGIT
NF F
1 2
40 to 55 inclusive
Separates Basic Group from Bore Size For Round Bores For Square Bores
1.3/16" to 2.3/16" inclusive 40mm. 45mm. and 50mm. 7/8" to 1.1/2" inclusive (Across Flats) denoted in 1/8" units (eg. 7/8" = 7) 30mm. and 40mm. (Across Flats) denoted as 9A and 12A Respectively
LUBRICATION FACILITY
57
Section 7
Notes
Designation Systems
58
Notes
59