Professional Documents
Culture Documents
Equipment Site :
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
1 INDEX
1 2
2.1 2.2 2.3
INDEX INTRODUCTION
Document Revision History Document Information Requirements
2 5
5 5 5
3
3.1
COMMUNICATION
Local Communication Verification 3.1.1 POWER-B LOCAL COMM. port 3.1.2 MGMT TILE LOCAL COMM. port Remote Communication Verification Remote Communication Parameters Settings 3.3.1 Communication Tests Engineering Comments
6
6 6 6 7 7 8
3.2 3.3
4
4.1
9
9 9 9 9 9 11 12
4.2
5
5.1
CARDS
Cards Status Verification 5.1.1 TL1 Commands Required 5.1.2 Report Table 5.1.3 Cards Status Engineering Comments
13
13 13 13 14
6
6.1
INPUT
Input Line Configuration 6.1.1 TL1 Commands Required
Page :
15
15 15
2 of 35
Author:
Document Title :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
6.2
6.3
6.1.2 Report Table 6.1.3 Input Line Configuration Engineering Comments Input Line test 6.2.1 Input Verification 6.2.2 Input Line Engineering Comments Holdover functional test 6.3.1 Verification of the Holdover mode 6.3.2 Holdover Engineering Comments
15 16 16 16 19 20 20 23
7
7.1 7.2
24
24 24 24 24 25 25 25 26
7.3
8
8.1
OUTPUT
Output configuration 8.1.1 TL1 Commands Required 8.1.2 Report table Output Port verification 8.2.1 Testing Method 8.2.2 Output Port Engineering Comments
27
27 27 27 28 28 29
8.2
9
9.1
POWER
Verification of POWER cards operation 9.1.1 POWER Cards Operation 9.1.2 Verification of POWER Cards Redundancy Operation 9.1.3 Power Engineering Comments D.C. Power, Ground/Earth potential Verification 9.2.1 POWER Test, POWER FUSE, DC SAFETY Engineering Comments
30
30 30 30 31 32 32
9.2
10
10.1
33
33 33 33 33
Page :
Minor Alarm (MN) 10.1.1 TL1 Commands Required 10.1.2 Verification of the MAC card state 10.2 Major Alarm (MJ)
Document Title :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
10.3
10.2.1 Verification of the MAC card state Critical Alarm (CR) 10.3.1 Verification of the MAC card state 10.3.2 Alarm Levels Engineering Comments
33 34 34 34
11
35
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
2 Introduction
2.1 Document Revision History
Rev 1.00 1.01 1.02 1.03 Date of Change 22 Jan. 07 28 Mar. 07 26 Aug. 08 25 Sep. 08 Description Creation Correction and improvements Some corrections Augmented for field use, North America Authorised BIGR BIGR NOIA RAJO
2.3 Requirements
The following tools are required to execute this commissioning document: Small Flat Blade Screwdriver [1mm slot] for System Card Front Panel Screws (card removal or insertion) A laptop or computer with at least the SyncTerminal installed. The Laptop should have both Ethernet and Serial port capability. As an option, the laptop can be provisioned with SyncView Plus Element Manager Software. A Null Modem RS-232C cable (DB9s DB9s, pins 2<>3, 3<>2 and 5<>5 connected) to communicate locally with the OSA 5548C SSU An oscilloscope with minimum 30MHz bandwidth, BNC cables, external 50 and 75 Ohm through-termination adapters (BNC<>CEI 1.0 adapting cables if so equipped on outputs) At least one input reference signal connected to the 5548C SSU, with a Phase Quality Level equal to, or higher than the quality of the THC cards installed in the 5548C SSU A Frequency reference source BNC-BNC cables less than 5 meters long, with 50 ohm impedance for any 2.048 MHz signals, and 75 ohm impedance for any 2.048 Mb/s signal source GPS Antenna, and Lightning Protection, installed and connected, if any GPS card installed Anti-Static Protection Wrist Strap for removal and insertion of cards if required, temporary Anti-Static mat or bag available for any cards removed Digital Multi-Meter (DMM) capable of measuring Voltage to 3.5 digits with < 1% error to 200 Volts Direct Current (D.C.) and Resistance Measurement to a resolution of 100 milliohms (0.1 ohms) {minimum}
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
3 Communication
3.1 Local Communication Verification
3.1.1 POWER-B LOCAL COMM. port
Connect a Null Modem Serial cable end to the front LOCAL COMM port located on the POWER-B card front panel and connect the other end to the serial port of your laptop or computer. Run the SyncTerminal and configure it to access the OSA 5548C via RS-232. Test topic Verify that the SyncTerminal show the following message once connected: Connecting to COM1/2 Connected Send the following TL1 command: RTRV-HDR:::CTAG; And check that the following answer has been responded: SID DATE TIME M CTAG COMPLD ; OK Partially Failed N/A
OK
Partially
Failed
N/A
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
M ;
eee.fff.ggg.hhh
N/A
255.255.255.000
N/A
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
SyncView Plus and SyncTerminal are both capable Commissioning Tools For Serial connections, use the right Null Serial DB9s DB9s cable, and set the COM port correctly. For Ethernet connections, ensure that the Laptop/CPU IP settings are in the same subnet segment as the 5548C under test. For 5548C IP connection, use port 8000/8023. If the Laptop can PING the 5548C successfully, SyncView+ and SyncTerminal will work correctly. The bottom pictures indicate locations of front and rear COM serial connections on the E200 model.
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
4.1.2.2 Reported Value (user setting) Shelf name (SID): site Date: Time: 12:00 Check Local UTC Offset 5548C ALARM HISTORY INITIALIZED
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
It is important to identify the components in the shelf at the time of commissioning for future reference. As shown in the example on the next page, each card is identified with part number, serial and revision number (shown as highlighted for INC-1-A). 4.2.1.2 Cards Inventory Report Paste the TL1 commands answer below.
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
Tiles Inventory
4.2.1.3 For 5548C SSU-E60 Slot Number A21 A22 A23 Tile Description POWER A TILE INPUT TILE OUTPUT TILE (GROUP 1)
A014124 o o o o o o o o o o o o A014448 CEI 1.0/2.3 ASYM: A014438 20x SUB-D SYM A014444 2x 20 pins IDC ribbon cable A014635 Blank A014166 CEI 1.0/2.3 ASYM: A014438 20x SUB-D SYM A014444 2x 20 pins IDC ribbon cable A014635 Blank A014166 CEI 1.0/2.3 ASYM: A014438 20x SUB-D SYM A014444 2x 20 pins IDC ribbon cable A014635 Blank A014166 A014594 A014125
A24
A25
A26 A27
Management Tile
A014594
A104
A105
A122
A123
Document Title : Document Type :
o o o o o o o o o
CEI 1.0/2.3 ASYM: 20x SUB-D SYM 2x 20 pins IDC ribbon cable Blank CEI 1.0/2.3 ASYM: 20x SUB-D SYM 2x 20 pins IDC ribbon cable Blank CEI 1.0/2.3 ASYM:
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
Slot Number
Tile Description
o o o o o o o o o o o o o o o o o o o 20x SUB-D SYM 2x 20 pins IDC ribbon cable Blank CEI 1.0/2.3 ASYM: 20x SUB-D SYM 2x 20 pins IDC ribbon cable Blank CEI 1.0/2.3 ASYM: 20x SUB-D SYM 2x 20 pins IDC ribbon cable Blank CEI 1.0/2.3 ASYM: 20x SUB-D SYM 2x 20 pins IDC ribbon cable Blank CEI 1.0/2.3 ASYM: 20x SUB-D SYM 2x 20 pins IDC ribbon cable Blank A014444 A014635 A014166 A014438 A014444 A014635 A014166 A014438 A014444 A014635 A014166 A014438 A014444 A014635 A014166 A014438 A014444 A014635 A014166
A124
A125
A126
A127
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
5 Cards
The STATUS of every card in the shelf will be recorded in this chapter.
NOTES: The GPS CARD STATUS LED may indicate RED if a GPS ANTENNA is not connected, or a faulty signal is received. This does not indicate that the GPS CARD is faulty. On GPS card STATUS RED indication, check the details of the number of satellites in view. Satellite Vehicles (SV) that indicate Signal/Noise Density levels of less than 30 dB should be considered too low to track. Five (5) or more SVs in view is acceptable for GPS operation. All other cards should indicate STATUS LEDs as GREEN. Investigate any alarms and correct all alarm conditions before proceeding. If input alarms are accepted and known, as for Inputs that are not yet connected, either disable those Input Lines, or note the condition in the Engineering Notes of this section. Use the selection of EMPTY for card slots that are not equipped. Use the selection OK for normal operation (STATUS=GREEN)
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
5.1.2.2 For 5548C SSU-E200 Card INC-1-A INC-1-B INC-2-A INC-2-B GPS-A GPS-B THC-A THC-B SGC-A SGC-B OUC-1-A OUC-1-B OUC-2-A OUC-2-B OUC-3-A OUC-3-B Status OK Compliant Card OUC-4-A OUC-4-B OUC-5-A OUC-5-B OUC-6-A OUC-6-B OUC-7-A OUC-7-B OUC-8-A OUC-8-B OUC-9-A OUC-9-B OUC-10-A OUC-10-B MAC-A MAC-B Status Compliant
Unavailable
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
6 Input
The Input Line Configuration of all INC cards in the shelf will be recorded in this chapter.
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
OK
Failed
N/A
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
6.2.1.2 Step 2 Manually remove all the input frequency reference sources from the Input Connectors and GPS antenna cable from GPS connectors. Test topic Observe/Confirm that STATUS LED is GREEN on INC-1-A Observe/Confirm that STATUS LED is GREEN on INC-1-B Observe/Confirm that STATUS LED is GREEN on INC-2-A (for SSU-E200) Observe/Confirm that STATUS LED is GREEN on INC-2-B (for SSU-E200) Observe/Confirm that STATUS LED is illuminated RED on GPS-A card Observe/Confirm that STATUS LED is illuminated in RED on GPS-B card Observe/Confirm that the LED related to the Input fed with Sync Frequency is illuminated RED SOLID on at least one input from IN1 to IN4 on the active INC card of the Group 1 Observe/Confirm that the LED related to the Input fed with Sync Frequency is illuminated RED SOLID on at least one input from IN5 to IN8 on the active INC card of the Group 2 (for SSU-E200) Observe/Confirm that the GPS LED is illuminated RED FLASHING on the GPS card(s), allowing enough time for the system to recover the GPS signal. OK Failed N/A
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
6.2.1.3 Step 3 Re-connect the frequency reference source to the Input Connectors and GPS antenna to the GPS connectors. Test topic Observe/Confirm that the LED related to the Input fed with Sync Frequency is illuminated GREEN SOLID on at least one input from IN1 to IN4 on the active INC cards of the Group 1 Observe/Confirm that the LED related to the Input fed with Sync Frequency is illuminated GREEN SOLID on at least one input from IN5 to IN8 on the active INC cards of the Group 2 (for SSU-E200) Observe/Confirm that the GPS LED is illuminated in GREEN on the GPS card(s), allowing enough time for the system to recover the GPS signal (aprox. 300 seconds) Observe/Confirm that ALL Related Alarms are cleared on the MAC card Verify that the Alarm is cleared with the software using the following command: RTRV-ALM::ALL:CTAG; Note: SyncView+ EVENT VIEWER can also be used to verify that the ALARM has CLEARED OK Failed N/A
Notes: Although only one Input Line is suggested for testing, all Inputs can be tested for functional status in the same way, by commissioning, enabling a test signal, removal of same test signal, and a reconnection of that test signal to test the Input STATES of the INC LEDs.
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
6.3.1.2 Step 2 RECOVERY OF HOLDOVER, INPUT RESTORAL Re-insert all INC and GPS cards and wait until at least one input line is recovered (after the WTR time expires). Completed Test topic When one line has recovered (after WTR time has elapsed, if applied) verify and observe that the THC active card indicates HOLDOVER LED FLASHING for approximately 1 minute and then extinguishes Verify that a line is reselected and that there is no - (dash) in the digital display, and that a number, or a letter g corresponding to the selected line is displayed on the THC digital display OK Partially Failed N/A
Note: On E200 models, valid THC digital Indications are 1,2,3,4,5,6,7,8,g or - . On E60 models, valid THC digital Indications are 1,2,3,4,g or - . The period indicator illuminates if there is one qualified input available if the current THC input is disqualified. 6.3.1.3 Step 3 THC PAIR SWITCHING ON THC FAILURE If two THC cards are installed in the shelf, remove the active one from its slot. If there is one THC in the shelf , skip to Step 7.1.1.3 Step 4. Completed One(1) THC/Not Applicable/skipped: Test topic Verify that the HOLDOVER LED is RED SOLID on the remaining THC for a short period; changing to RED FLASHING for approximately 1 minute on the remaining THC; and finally HOLDOVER LED extinguished (OFF) Verify that the previously selected line shown on the SELECTED INPUT display is the same as the first THC before it had been removed (i.e. if 1 was previously selected before THC removal, 1 should also be selected on the remaining THC after the locking process is completed) Verify that no effects are observed any of on the SGC card(s) LEDs during the manipulation Verify that no effects are observed on any of the OUC cards LEDs during the manipulation OK Partially Failed N/A
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
6.3.1.4 Step 4 SINGLE THC IN HOLDOVER Remove all INC cards and GPS from their slots. Only one THC in Holdover will feed the outputs. Completed: Test topic Verify that HOLDOVER LED on the remaining THC is ON permanently Verify that there is a - (dash) indicated in the SELECTED INPUT display on the active THC card Verify that the SGC cards remains with all their LEDs lit in GREEN permanently. Verify that the OUC cards remains with their two LEDs (E1 and/or f) and the STATUS LED lit in GREEN permanently OK Partially Failed N/A
6.3.1.5 Step 5 RESTORAL OF INPUT TO SINGLE THC IN HOLDOVER Re-insert all INC and GPS cards and wait until that at least one input line is recovered (i.e. after WTR time). Only one THC will recover to feed the outputs. Completed: Test topic Once that a line is recovered (after WTR time elapsed) verify that the THC active card get its HOLDOVER LED is ON, then blinking during approximately 1 minute and then getting extinguished. Verify that a line is reselected and that there is not a - (dash), but a number corresponding to the selected line displayed on the THC digital display OK Partially Failed N/A
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
6.3.1.6 Step 6 RESTORAL OF THC Re-insert the previously removed THC card in Step 3. If there is one single THC provisioned in the Completed shelf, skip to the next step. One (1) THC/Not Applicable/skipped: Test topic Verify that the newly inserted THC card is observed with OSCILLATOR LED RED/SOLID state, extinguishing after a warming and stabilization period, followed by a period with the HOLDOVER LED as RED SOLID, and changing to a FLASH status during approximately the last one (1) minute
Note that the OSC LED period is dependant upon module temperature at restart and the type of THC module.
OK
Partially
Failed
N/A
Verify that upon/following insertion of the THC card that no effects are observed on the other THC card LEDs Verify that upon/following insertion of the THC card that no effects are observed on any SGC card LEDs Verify that upon/following insertion of the THC card that no effects are observed on any OUC card LEDs
THC restoral after removal does require a period of stabilization and warmup.
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
For E200 models, continue testing below. Test topic Disable the priority 5 input and verify that the selected input is now the priority 6 as per shown on the active THC card SELETED INPUT display Disable the priority 6 input and verify that the selected input is now the priority 7 as per shown on the active THC card SELETED INPUT display Disable the priority 7 input and verify that the selected input is now the priority 8 as per shown on the active THC card SELETED INPUT display Disable the priority 8 input and verify that the selected input is now the priority 9 as per shown on the active THC card SELETED INPUT display On completion of the testing, reactivate all input fed to the OSA 5548C. Verify that all inputs are re-qualified.
OK
Partially
Failed
N/A
Notes; To Simplify this test, configure the SSU-E60 to use one E1 or Frequency Input, and then configure all virtual Input Lines to the one physical Input (i.e. FREQ1 or E1_1). For the SSU-E200 model, two physical inputs are required. Reset the priority to run in numerical order similar to the IL line numbers, with 5 steps for SSU-E60, and 9 steps for SSU-E200. Set the GPS as the last priority input in both cases. Observe that for every input rearrangement where that input is locked on the THC, there is a brief two~ minute period where the THC goes into protective Holdover mode, followed by Fast-Holdover recovery (signalled by Holdover LED flashing for 1 minute). During this interim period, the THC is testing the new Input selection for validity.
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
8 Output
8.1 Output configuration
8.1.1 TL1 Commands Required
Purpose TL1 Command / TL1 Answer Retrieving output group configuration, one RTRV-EQPT-OG::1-1..10-2:CTAG; after the other. RTRV-EQPT-OUC::1..10:CTAG; Retrieving Shorted Alarm detection state for each OUC, one after the other.
1-10 11-20 1-10 OUC-2 11-20 1-10 OUC-3 11-20 E200 models have 10 output groups 1-10 OUC-4 11-20 1-10 OUC-5 11-20 1-10 OUC-6 11-20 1-10 OUC-7 11-20 1-10 OUC-8 11-20 1-10 OUC-9 11-20 1-10 OUC-10 11-20
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
Port #
OUC 1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
9 Power
9.1 Verification of POWER cards operation
This test is designed to check the correct operation of both A and B POWER cards of the 5548C. Verify that power is fed to both POWER A & POWER B connectors.
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
OK
Failed
MEASUREMENT VOLTS
Correct Polarity
VOLTS
Correct Polarity
OHMS (averaged)
Observe the Installation of DC power and feed cables. Ask for the main breaker details , Bay numbers and proper Fuse Ratings. To maintain safety, 5548C models should always be fed from 10A breakers, and maintain proper distribution for the Main DC feed, and for the Relay Rack or Cabinet in which the Equipment is mounted. The Ground from the Rack or Cabinet (copper) bar should be no more than 1.0 Ohms and no longer than 2 meters in length.
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/
Attachments; INVENTORY PRINT OF SITE SHELF, ALL CARDS GPS ANTENNA SITE PICTURES LIGHTNING PROTECTION AND CABLE TRANSIT PICTURES PHASE TEST RESULTS , (optional) if applicable
Document Title :
Page :
Commissioning Document
1.04 2008
OSCILLOQUARTZ S.A. [NORTH AMERICA], 14 Inverness Drive East, Suite F-240, Englewood Colorado 80112-5640 +303-790-0771 / Fax +303-790-1911 E-mail : osaus@oscilloquartz.com / World Wide Web : http://www.oscilloquartz.com/