Professional Documents
Culture Documents
these moulds can be used only once, because the mould is destroyed after the metal has solidify. This will increase the cost of production. The sand mould can not maintain better tolerance and smooth surface finish In order to meet these requirements following casting methods may be used. Permanent mould Casting. Semi- Permanent mould casting. Slush Casting. Die Casting.
Centrifugal Casting.
Investment or lost wax casting Shell Moulding.
The use of sand core results in lower cost and allows cored operations of irregular shape or undercuts of such type where metal core will be too costly and difficult to handle on production basis.
Slush Casting:
Die Casting:
The die casting is that casting which uses the permanent mould (Die) and the molten metal is introduced into it by means of pressure. The casting produce is required little machining.
The dies are usually made in to two parts which must be locked before molten metal is forced into them under high pressure of 7 to 700MPa. The pressure may be obtained by the application of compressed air or by hydraulically operated piston.
The ferrous metals are not die-casted because of high pouring temperature. Two types of die casting machines used for die casting. 1. Hot chamber die casting Machine. 2. Cold Chamber die casting Machine.
In the second method the plunger acts inside cylinder formed at the end of the goose neck which is immersed in a pot of molten metal. A port is provided near the top of the cylinder to allow the entry of the molten metal. The downward stroke of the plunger pushes the molten metal through the goose neck into the die.
The hot chamber die casting machine is used for casting zinc, tin lead and other low melting alloys.
Cold Chamber Die Casting: In cold chamber die casting machine the melting unit is separate and molten metal is transferred to injection mechanism by ladle. The pressure is vary from 21 to 210MPa and in some cases may reach to 700MPa. More pressure is required for semi-molten alloys to compensate for reduced fluidity resulting from low temperature. This process is used for casting Aluminum, magnesium, copper base alloys. The machine consists of a pressure chamber of cylindrical shape fitted with piston or ram that is operated by hydraulic pressure. A measured quantity of molten metal is brought in to a ladle and forced in to the closed die sections by applying hydraulic pressure on piston. 1. The metal is loaded in the chamber. 2. The plunger forces the metal into the die cavity. 3. After the metal solidifies the die is opened. 4. The casting, together with slag of the excess metal, is ejected from the die.
6. The rapid cooling rate produces high strength and quality in many alloys.
7. The die retains its life for longer period.
Disadvantages of Die Casting: 1. The cost of equipments and die is high. 2. Limited range of non-ferrous alloys used for die casting. 3. The die casting are limited to size.
13 (12 Si)
300
150
2.5
Brass 858 (60 Cu) Magnesium AZ91B (9 Al 0.7 Zn) Zinc No. 3 (4 Al)
380
200
15
230 280
160 -
3 10
5 (4 Al 1 Cu)
320
Appliances, automotive components, electrical motor frames and housings, engine blocks. Complex shapes with thin walls, parts requiring strength at elevated temperatures Plumbing fixtures, lock hardware, bushings, ornamental castings Power tools, automotive parts, sporting goods Automotive parts, office equipment, household utensils, building hardware, toys Appliances, automotive parts, building hardware, business equipment
Centrifugal Casting: A casting processes in which molten metal is poured and allowed to solidify while mould revolving. The centrifugal casting are classified as
Advantages of True centrifugal casting: It is a quick and economical than other method. It eliminates the use of risers, feed heads, cores. The ferrous and non-ferrous metals can be casted by this process.
The castings produced by this process have dense and fined grained
structure with all impurities forced back to the centre where they can be frequently machined out.
Schematic illustration of the centrifugal casting process. Pipes, cylinder liners, and similarly shaped parts can be cast by this process.
Semi-centrifugal casting: This process is used for making large size castings which are symmetrical about their own axis such as pulleys. In this process the mould is rotated about its vertical axis, and the molten metal is poured into a central sprue from where it enters the hub. From the hub it is forced outward to the rim by centrifugal force. If a central hole is required in the casting, a dry sand central core may be used in center. The speed of rotation is less than that of true centrifugal casting. This is due to the large size casting and there is a tendency of the molten metal to flow out of the mould joint. Due to the lower speed the pouring pressure produced is low and thus the impurities are not effectively separated from the metal.
Centrifuging: The casting of irregular shape can produced and the large number of small size castings can be produced at one time. In this process a number of small cavities are made symmetrically around a common central sprue and the metal is fed to them by radial gates. The mould cavities are not rotated about their own axis but they are rotated about the central sprue which acts as the axis of rotation.
The pressure-casting process uses graphite molds for the production of steel railroad wheels.
Investment Casting:
The castings produced by this method are within vary close tolerances and do not requires subsequent machining.
The procedure for investment casting. 1. First of all a metal die for casting the wax patterns is made.
2. The wax pattern and gating systems are produced from the metal dies by injection. The wax is injected in to the mould at 50 0C to 80 0C and pressure of 3.5 to 7 MPa.
3. The wax assembly is dipped into a slurry of a refractory coating material. A typical slurry consists of silica flour suspended in ethyl silicate solution of suitable viscosity to produce uniform casting after drying. After dipping the assembly is coated by sprinkling it with silica sand and allowed to dry. 4. The coated wax assembly is now invested in the mould. This is done by inverting the wax assembly on a table, surrounding it with a paper-lined steel flask and pouring the investment moulding mixture consisting of either sand 95%, water 27 to 31% and 5% alumina cement or sand with 3% or more ethyl silicate or sodium silicate around the pattern. The mould material settles by gravity and completely surrounds the pattern as the work table is vibrated. The mould are then allowed to dry in air for 2 to 3 hours.
The procedure for investment casting. 5. The wax is melted out of the hardened mould by heating it in an inverted position at 90 0C to 150 0C. The melted wax may be collected and re-used. 6. The moulded is aging heated at the rate of 400C to 700C per hour from about 1500C to 10000C for ferrous alloys and 6500C to for aluminum alloys. The temperature is controlled so that the mould is at a temperature desirable for pouring the particular alloy. The investment moulds may be poured under simple gravitational force or under the force of applied air pressure or by centrifugal force.
Advantages of Investment Casting: The close tolerances ( 0.05 mm) are easily maintained. It produces extremely smooth surface. It eliminates most machining operations including thread cutting and gear tooth forming. It is adaptable to all metallic alloy.
Disadvantages of Investment Casting: The investment moulds as well as the materials from which they are made are single purpose, therefore they can not be reused. This increases the cost of production. The larger objects are impractical for investment casting due to equipment size limits.
Shell Moulding Process : The shell moulding process consists of making a mould that has two or more thin, shell like parts consisting of thermosetting resin bonded sand. It is mixed with sand as a powder form 3 to 10 % by weight. It may be applied as a liquid and then dried on the sand grains.
1. A metal pattern heated to about 1750C to 3500C is clamped over a box containing sand mixed with thermosetting resin 2. The box and pattern are inverted for a short time. The mixture when comes in contact with hot pattern, it causes an initial set and builds up a coherent sand shell next to the pattern. This takes 5 to 20 seconds only. The thickness of the shell is about 6mm to 18mm and is dependant on the pattern temperature, dwell time on the pattern and the sand mixture.
3. The box and pattern are brought in to its original position. The shell of resin bonded sand is retained on the pattern surface, while the unaffected sand falls into box. The shell still on the pattern is cured by heating it in an oven from 2500C to 3500C for 1 to 3 minutes. The time depends upon the type of resin and shell thickness. 4. The assembly is removed from the oven and the shell is stripped from the pattern by ejector pins. In order to obtain clean stripping a silicon parting agent may be sprayed on the pattern. 5. The shell halves are assembled with clamps and supported in flask with backing material. The shell mould is now ready for pouring.
Advantages of Shell Moulding: 1. The shell cast parts can be produced with dimensional tolerances of 0.2 mm. 2. A very smooth surface is obtained.
3. The dimensional accuracy and smooth surfaces reduces cleaning and machining cost.
Disadvantages of Shell Moulding: 1. The initial cost of the metal patterns and other specialised equipment is high. 2. The resin binder is more expensive than other binders.