Professional Documents
Culture Documents
Introduction
Objective
Define procedure to define Dual Cell procedures
Key Points
UARFCN F1 (10622), F2 (10597), F3 (10572) Preferred service F1 (R99), F2 (HSPA), F3 (HSPA) Preferred layer F1 (non-data card UE), F2 (data card UE) Local Cell Group F1 (1), F2 (2), F3 (2) Inter-frequency handover F2 to F1 and F3 to F1. Define co-site F1 ADJI on F2 and F3 cells. Define co-site ADJG on F2 and F3 RT FMCS on F2 and F3 to FMCS 11 (RSCP -70/-60, EcNo -10/-7)
Loh
WBTS Commissioning
Define procedure to define Dual Cell procedures at WBTS commissioning level
Loh
WBTS License
Loh
Loh
Loh
Details
Parameters RNC
HSDPAMobility (enabled) FRLCEnabled (enabled) DisablePowerInHSDPALayeringDecision (preferred to be disabled) MaxBitRateNRTmacdflow (65535 = no restriction) AMRLCmaximumBufferUE (configure accordingly) AMRLCRelatTXWindow (configure accordingly) HSDPADynamicResourceAllocation (enabled) DRRCForHSDPALayerServices (798) DCellVsMIMOPreference (DC preferred) MaxBitRateNRTMacdflow (no restriction) PDUSIzeCodeThreshold (10)
Parameters Iur
MaxIurNRTHSDSCHBitRate (default 9600) HSPAOverIur (enabled)
Parameters IuPS/CS
CNDomainVersion (5 = Rel7)
Loh
Details
Parameters WBTS
HSDPA14MbpsPerUser (enabled) NBAPCommMode (value 0 for FlexiBTS) BTSSupportForHSPACM (support)
Parameters HOPI
AdjiPriorityDCellCAHO (set priority) AdjiPriorityHSCAHO (set priority)
Parameters ADJI
AdjiNCHOHSPASupport (recommended to set to support, default is not support)
Loh
Details
Parameters WCEL (F2 & F3)
Tcell (Same value and different sector should have different cell group; 0,768,1536) SectorID (must be the same; PtxPrimaryCPICH) DCellHSDPAEnabled (activated in both cells) HSPDSCHCodeSet (code set 5, 8, 10, 12, 14, 15) HSUPAenabled (enabled) HSPAQoSEnabled (must be the same for both cells, default QoS prioritization is not in use for HS transport) DCellHSDPAFmcsId (must have a value. Follow HSDPA 43) MaxNumberHSDPAUsers (0 = no restriction) MaxNumberHSDSCHMACdFlows (0 = no restriction) MaxNumbHSDPAUsersS (0 = no restriction) MaxNumbHSDSCHMACdFS (0 = no restriction) DirectedRRCEnabled (enabled) DirectedRRCForHSDPAEnabled (enabled) DirectedRRCForHSDPALayerEnhanc (enabled) HSDPALayeringCommonChEnabled (enabled) CellWeightForHSDPALayering (F2 = 1, F3 = 0.5) HSDPALayerLoadShareThreshold (3) HSDPA64QAMallowed (1) MaxNbrOfHSSCCHCodes (1)
Loh
Details
Parameters WCEL (F2 & F3)
DCellHSDPACapaHO (3 periodical & event) HSCapabilityHOPeriod (5s) HSCapabilityHONumbUE (default 3) InterFreqMeasAveWindow (default 6) MaxNumberUECmSLHO (6) MaxNbrOfHSSCCHCodes (4, 1 for testing max TP) PWSMSDLimitDCHSDPA (default 5, need Power Saving Mode for BTS) PWSMAVLimitDCHSDPA (default 10, need Power Saving Mode for BTS) FDPCHEnabled (1 = enabled) HSPDSCHMarginSF128 (0)
Loh
Related Features
Loh
Features
Mandatory Features
RAN1906 Dual-Cell HSDPA 42Mbps (mandatory) RAN826 HSUPA (mandatory) RAN1638 Flexible RLC (mandatory) RAN1643 HSDPA 64QAM (mandatory) RAN852 HSDPA 15 Codes (mandatory) RAN1034 Shared HSDPA Scheduler for Baseband Efficiency (mandatory) RAN1258 HSDPA 14 Mbps per User (mandatory) RAN1011 HSPA Layering for UEs in Common Channels
Enhancement Features
RAN1201 F-DPCH RAN1848 Flexi BTS Multimode System Module RAN1226 HSPA Peak Rate Upgrade (Required for RNC196 and RNC450, current RNC is RNC2600) RAN1686 HSPA 72 Users Per Cell RAN1231 HSPA over Iur RAN1470 HSUPA 2ms TTI RAN981 HSUPA 5.8Mbps RAN1689 CS Voice Over HSPA RAN1762 Direct Resource Allocation for HSPA RAN2136 Fast L1 Synchronization RAN2136 Fast Dormancy RAN1022 24kbps Paging Channel RAN1596 HSPA Capability Based Handover
For internal use 12 Nokia Siemens Networks Loh
Loh
Layering Strategy
Carrier Layering
Layer F1 is set to non-HSPA layer (F1 is the preferred overall layer) Layer F2 is set to HSPA layer (F2 is the preferred HSPA layer) Layer F3 is set to HSPA layer
F3 - HSPA
F2 - HSPA
F1 R99
ADJI/ADJG
ADJI F3 to F1 and F2 to F1 (co-site, one way only) ADJG F3 to 2G and F2 to 2G (co-site, one way only)
For internal use 14 Nokia Siemens Networks
Loh