Professional Documents
Culture Documents
2008-06
ISSUE 1.0
HUAWEI Confidential
www.huawei.com
HUAWEI Confidential
auxiliary equipment
Master the hardware structure of BTS3900A
auxiliary equipment
HUAWEI Confidential
HUAWEI Confidential
HUAWEI Confidential
HUAWEI Confidential
and the -48 V 100 AH. The batteries can be grouped into the following
combinations:
When
V
100 AH through connecting the upper and the lower battery groups in parallel.
When
HUAWEI Confidential
HUAWEI Confidential
Heating film
The
provide suitable working temperature for the batteries. When the working
temperature in the battery cabinet is lower than the temperature
specification for the battery, the battery capacity declines. So the heating
film is installed in the battery cabinet to provide the optimal working
temperature for the batteries.
The
HUAWEI Confidential
HUAWEI Confidential
board
AFMU
board
DCDU-03A module
Sensors
(2) DCDU
module
HUAWEI Confidential
(4) APMI
board
(4)
Fan
(6) AFMU
board
APMI Board
The
APMI board refers to APM Power Monitor unit Interface board. The
APMI board is located at the upper left corner of the APM30 cabinet,
and performs the following functions:
Transfers
HUAWEI Confidential
APMI Board
Port
on the panel
Port
Connector Type
Quantity
Function
RS422
RJ45 connector
TX+, TX-,
RX+, RX-
IN1-IN3
OUT1
HUAWEI Confidential
AFMU Board
The
AFMU board refers to APM Fan Monitor unit Interface Board. The
AFMU board is located at the upper right corner of the APM30 cabinet,
and performs the following functions:
Provides
power port
Supplies
DC power to the two fans at the top of the cabinet and reports the
through
the signal transfer cable and then is reported to the BBU.
HUAWEI Confidential
AFMU Board
Ports
Port
Function
ALM
DC
INPUT
LED
Silkscreen
Color
Status
Description
Operation
LED
RUN
Green
ON steady
Blinking for 1s ON
and 1s OFF
OFF steady
ON steady
An alarm is generated.
OFF steady
Red
HUAWEI Confidential
DCDU-03A Module
The
cables are front accessed. The DCDU-03A performs the following functions:
Supports
Supports
supports power to the fan unit; LOAD1 to LOAD8, with the maximum current of 4 A,
supports power to the transmission equipment.
Provides
the surge protection alarm reporting function through the built-in surge
protection board.
HUAWEI Confidential
Sensors
door status sensor is made up of two parts, the magnet part and the switch part.
HUAWEI Confidential
Sensors
Temperature Sensor
The
sensor, internal ambient temperature sensor, and the air outlet temperature sensor.
HUAWEI Confidential
HUAWEI Confidential
Introduction of EMUA
Technical Specifications
Dimensions: 483mm284mm44mm.
HUAWEI Confidential
Power Input
supports input voltage detection. The alarm threshold for the input voltage can be
configured on the BTS and delivered to the EMUA.
provides two power input ports, which are protected from inverse connections.
Environment Monitoring
provides four ports for monitoring analog signals. Voltage-type sensors and
current-type sensors can be used.
Communication Ports.
HUAWEI Confidential
EMUA2432
EMUA4832
18V DC 36V DC
18V DC 36V DC
36V DC 72V DC
16 ports
32 ports
32 ports
(S1+/S1 S16+/S16)
(S1+/S1 S32+/S32)
(S1+/S1
voltage input
Boolean signal
S32+/S32)
Boolean signal
port
32 ports
32 ports
invalid)
DIP switch
settings
SW24B.
SW24B.
default settings.
Serial port
Maximum current in
Maximum current in
Maximum current in
protection
differential mode: 3
differential mode: 3
mode: 5 kA
common mode: 5 kA
in common mode: 5 kA
HUAWEI Confidential
Temperature
Humidity
Boolean signal
Analog signal
Relay output
control
Communication
Measured Object
Specification
Measurement range
0V DC 100V DC
Measurement precision
1V
Measurement range
20 80
Measurement precision
Measurement range
0%RH 100%RH
Measurement precision
5%
Measurement range
<10s
Measurement range
4mA 20mA 0V 5V
Measurement precision
1%
<1s
capacity
RS232 RS485
9600bit/s
rate
HUAWEI Confidential
HUAWEI Confidential
HUAWEI Confidential
Function
Setting
SW_ADDR
Selection of the
communication protocol
SW_BKE
SW_THE
SW-AE
SW_AV
sensor settings
SW12A
Bits 1-8 of the DIP switch SW12A correspond to input signals 1-8.
SW12B,
signal input
Bits 1-8 of the DIP switch SW12B correspond to input signals 9-16.
SW24A
SW24B
Bits 1-8 of the DIP switch SW24A correspond to input signals 17-24.
Bits 1-8 of the DIP switch SW24B correspond to input signals 25-32.
ON-high-level alarms; OFF-low-level alarms or is not used.
HUAWEI Confidential
HUAWEI Confidential
Technical Specifications:
The 75-ohm transmission interface box and the 120-ohm transmission interface
box have the same dimensions: 420 mm (L) 378 mm (W) 125 mm (H).
HUAWEI Confidential
HUAWEI Confidential
Technical Specifications:
The dimensions of the power interface box are 420 mm x 378 mm x 125 mm
(length x width x height).
The weight of the power interface box is 9.8 kg by default before delivery.
HUAWEI Confidential
The 110 V AC power interface box and the 220 V AC power interface box
have the same components, but they are different in MCB specifications.
HUAWEI Confidential
HUAWEI Confidential
Internal DDF
The
the BTS and the transmission equipment. There are two types of DDFs
available by installation positions, external DDF and internal DDF. The
internal DDF is further divided into the coaxial DDF (75-ohm) and the
twisted pair DDF (120-ohm). It is placed in the subrack reserved for the
transmission equipment in the cabinet or in the slot reserved for the
transmission unit in the auxiliary equipment.
Coaxial DDF
The coaxial DDF provides the access for eight coaxial E1s. It is 1 U in height and does not
provide the lightning protection function.
HUAWEI Confidential
Internal DDF
Twisted
Pair DDF
The twisted pair DDF provides the access for eight twisted pair E1s. It is 1 U in height
and does not provide the lightning protection function.
HUAWEI Confidential
Thank You
www.huawei.com