Professional Documents
Culture Documents
Injection Molding
Plastics Processes
Plastics 001
Injection Molding
• Module Objectives
– By the end of this module, you should be able to:
– Understand the basic operation of each process.
– Understand the key processing parameters.
– Understand several Advantages of each process.
– Understand several Disadvantages of each
process.
– Understand how to identify parts made by each
process.
Plastics 001
Injection Molding
Injection Molding
Plastics 001
Injection Molding
• Introduction
– Injection Molding is one of the most popular and
most used processes in Plastics. The largest
variety of parts are made with Injection Molding.
• To Read
– Review Chapter 6.3 before beginning the lesson.
Plastics 001
Injection Molding
• To Do
– Assignment 11: See the Assignments folder in our
course Angel space for this assignment.
Remember, all assignments are due by midnight
on the date stated on your syllabus.
– Take Quiz 7 after this lesson and before beginning
Module 6 Lesson 3.
Plastics 001
Injection Molding
• Topics
– Injection Molding Process
– Variations in the Process
– Materials and Material Requirements
– Key Processing Parameters
– Advantages and Disadvantages
– Competing Processes
– Future Development
Plastics 001
Injection Molding
• Introduction
– It is a high-speed process that can make quite
large to very small, solid parts with simple or
highly intricate 3D geometries.
– Process can hold extremely high tolerances.
– Tooling costs are high, so the process is best suited
for high-volume applications.
Plastics 001
Injection Molding
• Introduction
– Can produce high-gloss parts with high depth of
image and a wide variety of special effects
requiring little or no post-mold finishing.
– Insert molding allows production of parts with
integral decorative surfaces (paint films, foils,
carpet, fabric).
Plastics 001
Injection Molding
• Introduction
– Moldable Range of Part Sizes: As small as the
head of a pin to as large as an Automobile Bumper
or Fascia
Plastics 001
Injection Molding
• Plastification Stage
• Plastification Stage
– The pressure that builds up, because of the
material being forced in front of the screw, starts
to push the screw towards the back of the
injection unit. When the screw is pushed back to
a pre-set distance, the screw stops rotating. The
amount of material in front of the screw is
referred as the shot size.
Plastics 001
Injection Molding
• Filling Stage
– When the mold closes, the screw is pushed
forward. This fills the mold to 98% full.
– This filling is done at high speed.
– If the mold was completely filled, the pressure
would be too great and would push the mold
open.
Plastics 001
Injection Molding
• Filling Stage
Plastics 001
Injection Molding
• Packing Stage
– The last 2% of the part is filled during the second
stage of the injection molding cycle.
– As the molten polymer starts to cool, it shrinks.
Compensation for this shrinkage is done in this
stage. Without this compensation, the part would
shrink away from the mold walls.
– This stage is complete when the gate solidifies and
no more compensation can occur in the part.
Plastics 001
Injection Molding
• Packing Stage
Plastics 001
Injection Molding
• Cooling Stage
– When the gate is solidified, the screw builds up
another shot.
– The part is kept in the mold to solidify and retain
shape.
Plastics 001
Injection Molding
• Ejection Stage
– When the mold opens, the part is pushed out of
the mold.
Plastics 001
Injection Molding
• Material Requirements
– Sufficiently low viscosity to flow through the melt
delivery system and fill the mold’s geometry.
– Only extremely high molecular weight materials
cannot be processed in injection molding.
Plastics 001
Injection Molding
• Process Advantages
– Provides high production rates – particularly
when using multi-cavity tools.
– Capable of holding highest tolerances of any
plastics processing method.
– Tools equipped with hot runners have low
scrap rates.
Plastics 001
Injection Molding
• Process Advantages
– Once process settings are finalized, process can
operate automatically with minimal human labor,
except for secondary finishing.
– Process is capable of extremely complex shapes,
although this must be balanced against higher
tooling costs and more complicated operation and
maintenance.
Plastics 001
Injection Molding
• Process Advantages
– Because of the high pressures involved, process is
capable of reproducing an excellent – even mirror
surface finish, depending on finish on tooling.
Plastics 001
Injection Molding
• Process Disadvantages
– Compared to other plastics processes, tooling
costs are high.
– Some part details, such as undercuts, are not
easy to construct in the mold.
– Parts with high levels of residual stresses can
continue to shrink or warp for several days
after molding.
Plastics 001
Injection Molding
• Process Disadvantages
– It can take a long time to build the molds
because of the tighter tolerances and making
sure that the mold can withstand the high
pressures that are needed for the process.
– It is hard to predict accurate shrinkage.
Depending on how the part is processed, the
shrinkage can be changed. The process has a
huge effect on the parts final dimensions.
Plastics 001
Injection Molding
• Competing Processes
– Except for large parts, hollow parts can be
assembled from several injection molded parts.
• The traditional hollow parts processes are Blow
Molding, Rotational Molding, and Twin-Sheet
Thermoforming.
– Injection molding can make equivalent parts at
higher tolerances, assuming volumes justify higher
tooling and extra assembly costs, and aesthetic
standards will allow a welded area around the
part.
Plastics 001
Injection Molding
• Competing Processes
– Any plastic process could be a competitor of
injection molding. These other process could be
less costly and offer some properties that injection
molding cannot (e.g. very low molded stresses).
– Injection molding would be able to create the
parts with higher tolerance but likely at higher
costs unless production volumes were also high.
Plastics 001
Injection Molding
• Future Development
– Injection molding is almost always the first
process examined when converting metal parts to
plastic because it is so well suited to parts
consolidation.
– Developments in injection molding, such as liquid
silicone molding and gas-assist, make it more
attractive than other competing polymer
processes for some current applications.
Plastics 001
Injection Molding
• Future Developments
– In addition, new mold making techniques are
being evaluated to replace traditional methods of
insert creation. These techniques involve a laser
that melts powdered metal to create mold inserts
directly from a computer model.
Plastics 001
Injection Molding
• Future Development
– Computer control of the injection molding process
would allow instant modification of the process
based on a parts attributes.
– The use of CAE design software to automatically
design molds is still in its infancy.
– Molding variations, such as Micro-Molding,
MuCell, Liquid Silicone Injection Molding, … are
starting to be used more.
Plastics 001
Injection Molding
• Future Development
– Although CAE analysis of the injection molding
process has been around for many years, it is still
struggling to gain wider acceptance. Although it is
being used more in the medical and automotive
industries, it is still only being used on about half
of the molds being made in the US.